CTA ADD-PARAFS Bedienungsanleitung

x1 x1

INSTALLATION:

1A. Align the holes of the body (A) to the

base plates (B) as illustrated. Rotate in

(4) screws (G) using provided tool (J)

until securely tightened.

1. Mounting Base to Body

PACKAGE CONTENTS:

x4 x1

2. Setting up Cable Routing

2A. Using the provided weighted pendant, route the cable through the stand. You must first remove the VESA adapter

using provided allen tool to unscrew. Using the pendant tool (C), affix/tie the cable first, then fish it through the large hole

at the top, drop it through the body and fish the cable through until it has come out the backside hole as illustrated. After,

reattach the VESA adapter with screws (G) and provided tool. Make sure to pull cable through hole before you reattach

as illustrated above.

**Cable for device for

illustration and not

included

3. Adjusting VESA Adaptor

3A. Using provided tool (F),

rotate clockwise to lock

VESA adapter in place.

Rotate counterclocwise to

loosen and flex the adapter

for flexibility when VESA

compatible item is installed.

CTA Digital Floor Stand Component

For Kitting

ADD-PARAFS / ADD-PARAFSW / ADD-PARAFSS

INSTRUCTION - MANUAL

4. Setting up VESA Compatible Items

x4 **Enclosure and cable

for illustration and not

included

4A. Align the VESA holes of the body (A)

to the holes of your VESA compatible

device as illustrated. Rotate in (4) screws

(H) using provided tool (J) until securely

tightened.

5. Anchoring Base (Optional)

5A. Pre-drill holes into the surface aligning with

floorstand drill holes using drill (not included). Insert

anchors first into holes (E), and drill in screws from

top until securely fastened. If not screwing into

surface, using fillers (D) to plug into holes for a

seamless finish.

**Tablet for illustration

and not included

6. Removing VESA Adaptor for Monitor Setup

6A. Located the endcap piece on the side of VESA adaptor as illustrated and

remove with fingers. Using provided tool (F), loosen sides as shown. Remove the X

VESA center component

7. Attaching Monitor and Reassembling

7A. Align the now removed X VESA component with the VESA holes on

the back of your monitor. Rotate in the screws (I) using provided allen

key tool until securely tightened.

7B. WITH the X VESA attached to the monitor, place the entire setup

back onto the floor stand body. Align the VESA joint with the original hole

as shown above. Then using the provided tool, tighten the now

connected VESA joint. Place in the fillers for a seamless look afterwards.

**Monitor for

illustration and not

included

**Monitor for

illustration and not

included

Dieses Handbuch passt für folgende Modelle

Andere CTA Rack & Stand Handbücher

CTA

CTA PAD-SWM Bedienungsanleitung

CTA

CTA PAD-HSKSB Bedienungsanleitung

CTA

CTA PAD-HGTSB Bedienungsanleitung

CTA

CTA PAD-MSPC10 Series Bedienungsanleitung

CTA

CTA PAD-SWM Bedienungsanleitung

CTA

CTA PAD-TAM Bedienungsanleitung

CTA

CTA PAD-VPOS1W Bedienungsanleitung

CTA

CTA PAD-DSGK Bedienungsanleitung

CTA

CTA PAD-TAM Bedienungsanleitung

CTA

CTA PAD-CHKBM10 Bedienungsanleitung

CTA

CTA PAD-SCGS Bedienungsanleitung

CTA

CTA PAD-PARAF1 Bedienungsanleitung

CTA

CTA PAD-ASKM6 Bedienungsanleitung

CTA

CTA PAD-KMS Bedienungsanleitung

CTA

CTA PAD-CHKB Bedienungsanleitung

CTA

CTA PAD-ASKB10 Bedienungsanleitung

CTA

CTA PAD-PF1ICC Bedienungsanleitung

CTA

CTA PAD-WDM Bedienungsanleitung

CTA

CTA PAD-UGT Bedienungsanleitung

CTA

CTA PAD-2VDMWA Bedienungsanleitung

CTA

CTA PAD-HSKSBAE Bedienungsanleitung

CTA

CTA ADD-USGTWP Bedienungsanleitung

CTA

CTA PAD-PARAFPE Bedienungsanleitung

CTA

CTA PAD-PARAF1GT Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung