CTC Union INJ-IG60-24 Bedienungsanleitung

CTC Union Technologies Co., Ltd.

Far Eastern Vienna Technology Center

(Neihu Technology Park)

8F, No. 60 Zhouzi St., Neihu District, Taipei 114

Taiwan

T+886-2-26591021

F+886-2-26590237

E[email protected]

All trademarks are the property of their respective owners.

Technical information in this document is subject to change without notice.

Introduction

INJ-IG60-(E)24 is an industrial grade, single port, gigabit

Ethernet PoE (Power over Ethernet) injector. PoE technology

describes a system to pass electrical power safely, along with data,

on Ethernet cabling. The original IEEE 802.3af-2003 PoE standard

provides up to 15.4W of DC power to each device. The updated

IEEE 802.3at-2009 PoE standard also known as PoE+ or PoE plus,

provides up to 30W of power. Additionally, INJ-IG60-(E)24 can

provide up to 60W/72W through the non-standard use of all 4

pairs of category 5e cable. Housed in a rugged DIN rail or wall

mountable enclosure, this product is designed for harsh

environments, such as industrial networking, intelligent

transportation systems (ITS) and is also suitable for many military

and utility market applications where environmental conditions

exceed commercial product specifications. Standard operating

temperature range models (-10°C to 60°C) and wide operating

temperature range models (-40°C to 75°C) fulfill the special needs

of industrial automation applications.

Features

Provide one port IEEE 802.3af/at PoE

Provide power up to 36W (2 pair mode) and 72W (4 pair mode)

Function settings via DIP switch for easy installation

24/48VDC (20VDC~57VDC) redundant dual input power and

built-in very high efficient power booster

Constant and regulated PoE voltage at 55VDC

Alarm relay output for power failure

Smart LED indication

Support auto detection and classification for PoE application

Support short-circuit and current-overloading protection for

PoE application

Industrial grade EMS, EMI, EN50121-4, EN61000-6-2,

EN61000-6-4

Wide operating temperature range -40°C~75°C (INJ-IG60-E24)

IP30 rugged metal housing

Specifications

Ethernet Interface

Data input: Cat. 5e (above) RJ-45 (shielded) 10/100/1000M x 1

Data + PoE output: Cat. 5e (above) RJ-45 (shielded)

10/100/1000M x 1

Standards: IEEE 802.3, 802.3u, 802.3ab

PoE Standards: IEEE 802.3af, IEEE 802.3at

Quick Installation Guide

INJ-IG60-24 (V1.2)

INJ-IG60-E24 (V1.2)

Industrial Grade Gigabit Ethernet PoE Injector

Specifications (cont.)

Power

24/48VDC (20VDC~57VDC) redundant dual input power

Reverse polarity protection: Yes

Overload protection: Yes

Connector: terminal block

PoE Power Output: Ultra High Power 60W/72W PoE output

IEEE 802.3at 30W PoE output

IEEE 802.3af 15.4W PoE output

Consumption: Max. 31.5W@24VDC (30W for PoE output)

Max. 61.8W@24VDC (60W for PoE output)

Mechanical

Water & Dust Proof: IP30 Protection

Dimensions: 106 mm (D) x 39 mm (W) x 142 mm (H)

Mounting: DIN-Rail, Wall Mount (kits included)

Weight: 425 g

Environmental

Operating Temperature: -10°C ~60°C (INJ-IG60-24)

-40°C~75°C (INJ-IG60-E24)

Storage Temperature: -40°C~85°C

Humidity: 5%~95% (Non-condensing)

Certifications

EMC: CE

EMI (Electromagnetic Interference): FCC, FCC Part 15 Subpart

B Class A, CE EN55022 Class A

Railway Traffic: EN50121-4

Immunity for Heavy Industrial Environment: EN61000-6-2

Emission for Heavy Industrial Environment: EN61000-6-4

EMS (Electromagnetic Susceptibility) Protection Level:

EN61000-4-2 (ESD) Level 3, Criteria B

EN61000-4-3 (RS) Level 3, Criteria A

EN61000-4-4 (Burst) Level 3, Criteria A

EN61000-4-5 (Surge) Level 3, Criteria B

EN61000-4-6 (CS) Level 3, Criteria A

EN61000-4-8 (PFMF, Magnetic Field) Field Length:

300A/m, Criteria A

Safety: UL60950-1 (Pending)

Shock: EN60068-2-27

Freefall: EN60068-2-32

Vibration: EN60068-2-6

MTBF (MIL-HDBK-217): 763,725 hours

[email protected]

V1.2

- 2 -

- 1 -

To download this QIG or a more complete user manual, please visit

http://www.ctcu.com/Industrial/

www.ctcu.com

Connectors

Figure 1. Front Panel

INJ-IG60-(E)24 has two standard shielded RJ-45 connectors for

Ethernet cable connections. The connector labeled GbE (Data

input) will connect to Ethernet switch, while the connector

labeled GbE+PoE (Data + PoE output) will connect to PoE PD

device such as IP Camera, Access Point, IP Phone, Digital Signage

or any other PoE power device. The PoE mode is selected via a 4-

pole DIP switch. Please see the next page for the settings of the

PoE operation modes.

RJ-45 Ethernet Port Pinouts

Figure 2. RJ-45 Ethernet Port Pinouts

RJ-45 Ethernet & PoE Pin Assignments

No.

RJ-45 Ethernet

PoE Output

100Base-TX

1000Base-T

2 Pair/

Alt A

2 Pair/

Alt B

4 Pair

RX+

TRD 0+

V+

RX-

TRD 0-

V+

TX+

TRD 1+

V-

TRD 2+

V+

TRD 2-

V+

TX-

TRD 1-

V-

TRD 3+

V-

TRD 3-

V-

NOTE: For 2 Pair (Alt A & Alt B)/4 Pair DIP switch settings, please refer to page 4.

Power & Alarm Relay

Figure 4. Terminal Block Figure 5. Alarm

Relay Circuit

A removable terminal block provides both power and alarm

(Normally Closed) connections. Power can be provided through

the dual inputs from separate sources. The alarm relay contact

can be wired into an alarm circuit which senses an alarm

condition when the contact is broken. The alarm relay is normally

closed when there is no alarm condition (both PWR1 and PWR2

have source power). If either or both PWR have no power input,

the alarm relay will "open". Please note that the alarm relay

contact can only support 1A current at 24VDC. Do not apply

voltage and current that exceed these specifications.

LED Indicators

LED

Color

Description

PWR1

PWR2

Green

Lit if power is connected and active at the

PWR1or PWR2 input terminal connection.

Off

PWR1 or PWR2 is not connected.

Fault

Amber

Lit if either one power input is connected.

Off

Both PWR1 and PWR2 have source power.

Alt A/PoE

Alt B/PoE

Green

Lit when a PD device is connected to the

GbE+PoE RJ-45 connector and the Injector

is feeding power in Alt A or B mode.

Blinking

One of the Injector faults (overload, short

circuit or over-temperature) occurs.

NOTE: If both Alt A and Alt B LED indicator are lit in Green, this indicates that the

Injector operates in 4 Pair high power application.

DIP Switch Function Descriptions

Figure 3. DIP Switch

DIP

No.

Status

Setting

Function Description

OFF *

Alt A

Feeding power on the 1&2, 3&6 wire pairs.

Also see DIP Switch 2.

Alt B

Feeding power on the 4&5, 7&8 wire pairs.

Also see DIP Switch 2.

OFF *

STD

The injector provides PoE output 15.4W for

IEEE 802.3af or 30W for IEEE 802.3at. Also

see DIP Switch 1.

High

The injector provides PoE output up to 36W

for IEEE 802.3at. Also see DIP Switch 1.

OFF *

2 Pair

Feeding power via data pair (Alt A) or spare

pair (Alt B). Also see DIP Switch 1 and 2.

4 Pair

Feeding power via both data pair (Alt A) and

spare pair (Alt B). Also see DIP Switch 4.

OFF *

PD-A

This mode is compatible with the general

PD devices at either 2 pair mode (DIP No. 3

OFF) or 4 pair mode (DIP No. 3 ON). Also see

NOTE 2.

PD-B

This mode is compatible with particular PD

devices at high-power 4 pair mode (DIP No.

3 ON) installation such as AXIS®Q60 series.

NOTE 1: By default, all DIP switches are set to OFF (marked with *).

NOTE 2: For 2 Pair mode, DIP Switch 4 must be set to OFF.

NOTE 3: After changing the DIP switch setting, you must restart the device to

activate the setting.

PoE Power & DIP Switch Settings

DIP

No.

Alt A

15.4W/30W

Alt B

15.4W/30W

Alt A

36W

Alt B

36W

4 Pair

PD-A

60W

4 Pair

PD-B

60W

4 Pair

PD-A

72W

4 Pair

PD-B

72W

OFF

Installation

The injector comes with both wall mount and DIN rail hardware

brackets. When installing the DIN rail bracket, be sure to correctly

align the orientation pin.

Figure 6. DIN Rail Figure 7. Wall Mounting

The injector with DIN Rail bracket has a steel spring in the

upper rail of the bracket. This spring is compressed for mounting

and un-mounting by applying downward force.

Figure 8. Mounting Figure 9. Un-mounting

Application

Figure 10. INJ-IG60-(E)24 Injector Application

- 3 -

Normally Closed

(NC)

Fault

- 5 -

www.ctcu.com

- 6 -

- 4 -

Non-PoE Ethernet Switches

Up to 330 feet or 100 meters

INJ-IG60-(E)24

PoE PD Device

(ex. AXIS®Q60 series

in 60W mode)

Data

Data +

15.4W/30W, 36W,

60W or 72W PoE

Dieses Handbuch passt für folgende Modelle

Andere CTC Union Laborausrüstung Handbücher

CTC Union

CTC Union INJ-IG02-PH Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung