CUES Solid FX Bedienungsanleitung
Rev Date ECN Description
-06/07/2021 -Initial Release
Document Number:
SF973-INST
Description:
SolidFX Mud Master Kit
Instruction Sheet
Signature CHKR: ____________________
Signature ENGR: ___________________
Signature MFG: ____________________
1
SF973-INST
Tony Winiewicz
7/6/21
7/19/21
Ludwig Hupe
RELEASED TO PRODUCTION - DATE: 7/19/2021
2
NOTES –UNLESS OTHERWISE SPECIFIED
1. Applying blue threadlocker (440061) to all threaded fasteners is
recommended.
2. Where brown threadsealant (445091) is specified, Teflon tape (440350)
may be used as an alternative. Pressurizing the system and leak
checking all hoses, PTC fittings, and NPT fittings is recommended.
3. Applying DeoxIT to electrical connections is recommended.
4. Dust caps should be applied to all receptacles that are not in use.
5. When plugging in cables/connectors, make sure to match the notch
positions of the cable and receptacle before plugging in. Do not force
cables into receptacles. Install connectors by threading them then
pushing the connector in. Repeat until connections are snug.
SF973-INST
•Unplug the electric lift and
the transmission.
•Unplug all of the lights.
•Remove the rear cover and
cut the zip tie to remove
the TM356 cable.
•Reinstall the rear cover and
apply dust caps and dummy
plugs to the TM356 cable.
•Hardware:
•160553
•EC431
•EC3465
•MS398
•The cables shown will not
be needed in this
configuration and should be
kept for normal Mud
Master operation.
3
SF973-INST
•Remove the electric lift
from the Mud Master
Chassis.
•The electric lift will not be
needed in this
configuration. Retain
hardware for future
installation.
•Install SF750 onto the Mud
Master chassis as shown.
•Mounting hardware:
•4X – 101022
•4x – 101740
4
SF973-INST
5
•The Rear View Camera (SF385) will now be mounted to the Light Array
(SF380). Installation of the LiDAR (SF362) will also be covered.
•Remove the two screws
shown RVC.
•Repeat for the 2 screws on
the other side.
•Set these 4 screws aside for
reassembly.
•RVC subassembly should
now be removed from the
mounting plate.
SF973-INST
•Remove the 3 screws shown (left) and set aside for reassembly.
•Install the LiDAR onto the RVC (right) using the four M3 screws provided
with the LiDAR. Hardware: 4X –HW952
•Reinstall the intake/blower portion of the assembly using the three screws
that were previously removed (left). Install the mounting plate to SF380 using
the five screws that were bagged and tagged with SF385 (right).
6
SF973-INST
7
•Note: When installing the
LiDAR/RVC assembly, make
sure to route the LiDAR
cable as seen below.
•Reinstall the RVC/blower
subassembly to the
mounting plate using the 4
screws that were previously
removed.
•The light array will now be mounted to the top half of the manual lift
(SF749). This will allow for the remaining components to be mounted
and cables and tubing to be routed.
SF973-INST
8
•Flip over both, the SF380
(with SF385 mounted) and
SF749.
•Align SF749 as shown.
•Note: It may be necessary
to loosen the mounting
tabs on SF380.
•Fix the SF749 to the light array using the four button head screws
provided with SF380.
SF973-INST
9
•Assemble the regulator and fittings in the orientation shown below. All
fittings should be tightly fastened. Use brown threadsealant (PN 445091) on
all mating threads. Brown threadsealant has a 24 hour cure time and
should be fully cured before supplying pressure through the fittings.
•Using brown threadsealant,
install the set screw
provided with SF239 as
shown (left).
•Rotate the valve on SF252
counterclockwise until it is
all the way “Closed”.
•Screw the SF225 pressure
tank into SF252.
•Note: DO NOT open valve
until threadsealant has
cured.
•Once brown threadsealant
has cured, turn valve SF252
clockwise until it is all the
way open and set SF239
regulator to 60 psi.
SF973-INST
SF252
HW2989
HW258
HW793
SF239
SF752
HW2979
Flow Direction
Set Screw
Note: Teflon tape (PN 440350) can
be used in place of brown
threadsealant.
•Note orientation of SF791.
•Next SF251 will be
mounted to SF791.
•Mount SF251 to SF791.
•Mounting Hardware:
•2X – 101024
•2X - 101736
10
SF973-INST
Andere CUES Analytisches Instrument Handbücher
