RIDGID SeeSnake Compact Bedienungsanleitung

Centering Guides

Installing the SeeSnake®

Star-Type Centering Guides

Centering guides can improve the picture by bringing the

camera closer to the pipe’s center, allowing the camera

to see an equal amount of the pipe wall in all direc-

tions. Centering guides also help by raising the camera

out of sludge that is often found below the water line. This

helps keep the lens cleaner, longer, reduces wear and

tear on the LED Ring (

Figure 18).

We recommend using centering guides whenever pos-

sible, but if you are having trouble pushing the camera in

a particular pipe, try it without the guides.

Figure 18 – Centering Guides improve vision by allow-

ing the camera to see an equal amount of

pipe wall in all directions and by raising the

camera out of sludge. They also reduce wear

on the LED ring.

Whether or not you use guides, how many you use,

and where you place them on the spring causes the

camera to behave differently. The best advice is to ex-

periment and decide what’s best for the given job.

One centering guide near the front end of the camera

may bias the camera head upward. This could be bene-

ficial if you need to see the top of the pipe during your

inspection.

Move the guide back a little and the camera head may

bias downward when you push and upward as you pull

back. This could help you see the top and bottom of

larger pipes more easily.

Two centering guides will tend to keep the camera head

aimed toward the center of the pipe, allowing you to

see more of the pipe at once.

Centering guides should be pre-stressed prior to use for

increased flexibility. To do this, slowly bend the spikes

back and forth from the tip (not the base) a few times be-

fore use (

Figure 19)

Figure 19 – Pre-stress tabs by placing your finger at the

top of the spike and slowly pushing the spike

90 degrees. Repeat in the other direction.

Star-type centering guide assembly consists of two parts -

two steel c-ring and the plastic centering guide

(Figure 20).

Figure 20 – Star-Type Centering Guide Components. You

may use from one to three guides.

SeeSnake®Compact and Color Compact

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

SeeSnake®Compact and Color Compact

Installing Star-Type Centering Guides

1. Position a centering guide and two c-rings over the

spring, with the centering guide between the c-rings

(Figure 21).

Figure 21 – Guide and C-Rings Positioned On Spring

Assembly.

2. Position the opening in the centering guide 180 de-

grees opposite the opening in the c-rings (

Fi-

gure 22).

3. Press the c-rings into the grooves on each side of

the centering guide until the c-rings snap into place.

It’s easiest if you place the closed portion of the c-

ring into the groove and work toward the open end

(Figure 22).

Figure 22 – Press the c-rings into the grooves on the

centering guide. Make sure the openings in

the c-rings are 180 degrees opposite the

opening in the pipe guide.

Removing Star-Type Centering Guides

1. Pry off each c-ring with the tip of a flat blade screw-

driver inserted near the open end of the ring and

the base of the spikes

(Figure 23).

Figure 23 – Place flat tip of screwdriver between c-ring

and base of spike and pry c-ring out of

groove.

2. Slide the c-rings and centering guide over the camera

head.

Installing the SeeSnake®Compact, and

FlatPack Ball-Type Centering Guides

Ball-type centering guides consists of two halves that are

pre-assembled at the factory, and two steel clips that

hold the guide in place on the spring.

Figure 24 – Centering guides improve vision by allow-

ing the camera to see an equal amount of

pipe wall in all directions and by raising the

camera out of sludge. They also reduce

wear on the LED window.

Figure 25 – Retaining Rings in Locked Position

Retaining Rings

Locked

Open Side of Guide

Closed Side

of Rings

C-Rings

Figure 26 – Unlock Retaining Rings by pulling them up

with a flat-bladed screwdriver.

Figure 27 – Slide Ball Guide over spring and push Retain-

ing Rings down to lock the guides in place.

SeeSnake®Compact and Color Compact

Retaining Rings

Unlocked

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

FAX 781.665.0780 - TestEquipmentDepot.com

Andere Handbücher für SeeSnake Compact

Dieses Handbuch passt für folgende Modelle

Andere RIDGID Analytisches Instrument Handbücher

RIDGID

RIDGID SeeSnake Compact Bedienungsanleitung

RIDGID

RIDGID micro CA-100 Bedienungsanleitung

RIDGID

RIDGID micro LM-400 Bedienungsanleitung

RIDGID

RIDGID micro CA-350 Bedienungsanleitung

RIDGID

RIDGID micro CA-330 Bedienungsanleitung

RIDGID

RIDGID SEESNAKE CS6X Bedienungsanleitung

RIDGID

RIDGID micro CA-25 Bedienungsanleitung

RIDGID

RIDGID SeeSnake STANDARD Bedienungsanleitung

RIDGID

RIDGID SeeSnake Micro Bedienungsanleitung

RIDGID

RIDGID SeeSnake microReel Bedienungsanleitung

RIDGID

RIDGID SeeSnake Micro Bedienungsanleitung

RIDGID

RIDGID micro LM-400 Bedienungsanleitung

RIDGID

RIDGID micro CA-300 Bedienungsanleitung

RIDGID

RIDGID micro CA-150 Bedienungsanleitung

RIDGID

RIDGID SeeSnake NanoReel Bedienungsanleitung

RIDGID

RIDGID SeeSnake microReel Bedienungsanleitung

RIDGID

RIDGID SeeSnake Micro Bedienungsanleitung

RIDGID

RIDGID seeSnake DVD Pak Bedienungsanleitung

RIDGID

RIDGID micro CA-100 Bedienungsanleitung

RIDGID

RIDGID micro CA-25 Bedienungsanleitung

RIDGID

RIDGID SeeSnake Compact C40 Bedienungsanleitung

RIDGID

RIDGID SeeSnake DVDPak2 Bedienungsanleitung

RIDGID

RIDGID SeeSnake Mini Bedienungsanleitung

RIDGID

RIDGID micro CA-350x Bedienungsanleitung

Beliebte Analytisches Instrument Handbücher anderer Marken

Cocraft

Cocraft NLT04 Bedienungsanleitung

M&C

M&C GENTWO PMA1000 Bedienungsanleitung

MICRO-EPSILON

MICRO-EPSILON optoncdt 1700 Bedienungsanleitung

CONDTROL

CONDTROL XP4 PRO Bedienungsanleitung

Extech Instruments

Extech Instruments BR200 Bedienungsanleitung

Dewetron

Dewetron DEWE-30-16 Produkthandbuch

EXTOL PREMIUM

EXTOL PREMIUM 8820043 Montage- und Bedienungsanleitung

Teledyne

Teledyne 3000PA Bedienungsanleitung

YDLIDAR

YDLIDAR TIA Bedienungsanleitung

Olympus

Olympus IPLEX FX Series Bedienungsanleitung

Bosch

Bosch GLM 50 C Professional Bedienungsanleitung

Reflecta

Reflecta DigiEndoscope Bedienungsanleitung

Chinavision

Chinavision CVACZ-G696 Montageanleitung

Fuji Electric

Fuji Electric ZKMA Bedienungsanleitung

Teledyne

Teledyne 3300TA Bedienungsanleitung

VOLTCRAFT

VOLTCRAFT IC-100HD Bedienungsanleitung

Würth

Würth MASTERVISION MINI REC Bedienungsanleitung

AMI

AMI 2001LC Bedienungsanleitung