Culligan Medallist Plus Series Bedienungsanleitung

Culligan

Medallist®

& Medallist

Plus Series®

Automatic

Water Filter

Owners Guide

Thank You

And Welcome To Your New World Of Better

Living With Culligan Water.

The Culligan Medallist Plus Series®with Cullar®ﬁlter has been tested and

certiﬁed by WQA against WQA S-200 for the effective reduction of aesthetic

Chlorine Taste and Odor up to 180,000 gallons as veriﬁed and substantiated

by test data.

The Culligan Medallist Plus Series with Cullneu®ﬁlter has been tested and

certiﬁed by WQA against WQA S-200 for neutralization up to 21,750 gallons

as veriﬁed and substantiated by test data.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate

disinfection before or after the system.

For installations in Massachusetts, the Commonwealth of Massachusetts Plumbing

Code 248 CMR shall be adhered to. Consult your licensed plumber for installation

of the system. This system and its installation must comply with state and local

regulations. The use of saddle valves are not permitted.

If this is your ﬁrst experience having ﬁltered, conditioned water in your home, you’ll be amazed at the

marvelous difference it makes. We promise that you’ll never want to be without it again.

Congratulations, too, on selecting one of the “ﬁrst family” of water ﬁlters in the prestigious Culligan

Medallist Series. With Culligan’s many years of knowledge and experience in water treatment, you

can be conﬁdent that the model you selected has been designed and engineered to provide years of

service with a minimum of care and attention.

Products manufactured and marketed by Culligan International Company (Culligan) and its afﬁliates

are protected by patents issued or pending in the United States and other countries. Culligan reserves

the right to change the speciﬁcations referred to in this literature at any time, without prior notice.

Culligan, Culligan Medallist Series, Cullar, Filtr-Cleer, Cullneu, Accusoft, Culligan Man and www.

culligan.com are trademarks of Culligan International Company or its afﬁliates.

Table of

Contents

Performance Data Sheets are included in this manual for various Culligan Medallist Series®Softener

models. Refer to the Performance Data Sheet for your speciﬁc softener, as there are slight differences

between the models. The softener warranty is located on page 19 of this Owner’s Guide.

Speciﬁcations.......................................................4

Introduction.........................................................5

Familarization.......................................................6

Programming .......................................................7

Things to Check Before You Call for Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

CareandCleaningofyourWaterFilter....................................11

Recommended Preventative Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

WhenandHowtoBypassyourWaterFilter.................................12

Culligan Medallist Plus Series® CullneuFilterPDS ............................13

Culligan Medallist Plus Series®CullarFilterPDS ..............................14

Culligan Medallist Plus Series® 8” and 10” Cullneu Filter PDS. . . . . . . . . . . . . . . . . . . . . 15

Culligan Medallist Plus Series®8” and 10” Cullar Filter PDS. . . . . . . . . . . . . . . . . . . . . . 16

Culligan Medallist Plus Series®8” and 10” Filtr-Cleer Filter PDS . . . . . . . . . . . . . . . . . . . 17

RecordsandData...................................................18

Warranty.........................................................19

Medallist 8“ Medallist 10” Medallist Plus 10”

General

Mineral Tank Size18 x 44 in. 10 x 54 in. 10 x 54 in.

Control 3/4” Power Valve 3/4” Power Valve 1” Power Valve

Timer Electronic Electronic Electronic

Temperature Limits 33-120°F 33-120°F 33-120°F

Water Pressure Limits 20-120 psi 20-120 psi 20-120 psi

Water Pressure Limits (Canada) 20-90 psi 20-90 psi 20-90 psi

Electrical Requirements 24V/60 Hz 24V/60 Hz 24V/60 Hz

Electrical Power Consumption, Min./Max. 3 Watts/35 Watts 3 Watts/35 Watts 3 Watts/35 Watts

Filtr-Cleer®

Rated Service Flow 7.8 gpm 8.9 gpm 12.0 gpm

@ Initial Pressure Drop @ 15 psi @ 15 psi @ 15 psi

Minimum Practical Filtration Size 10 microns 10 microns 10 microns

Maximum Particulate Matter 150 NTU 150 NTU 150 NTU

Maximum Suspended Solids 150 mg/L 150 mg/L 150 mg/L

Drain Flow, Maximum34.5 gpm 7.0 gpm 7.0 gpm

pH Limitation 6.0 - 9.5 6.0 - 9.5 6.0 - 9.5

Recharge Time480 min. 80 min. 30 min.

Recharge Water Consumption, Av.5100 gal. 115 gal. 140 gal.

Freeboard210.5 ± 1 inches 11.5 ± 1 inches 19 ± 1.5 inches

Height Overall 51 in. 63 in. 60 in.

Cullar®

Rated Service Flow 4.0 gpm 4.0 gpm 6.0 gpm

@ Pressure Drop @ 5.0 psi @ 5.0 psi @ 6.0 psi

Drain Flow, Maximum32 gpm 6.0 gpm 6.0 gpm

pH Limitation 5.0 - 11.0 5.0 - 11.0 5.0 - 11.0

Recharge Time480 min. 80 min. 30 min.

Recharge Water Consumption, Av.553 gal. 83 gal. 110 gal.

Cullar Media Volume 0.75 cu. ft. 1.0 cu. ft. 1.5 cu. ft.

Cullsan®Underbedding Media Amount 10 lbs. (.1 ft3) 20 lbs. (.2 ft3) 20 lbs. (.2 ft3)

Freeboard214 ± 1 inches 24 ± 1 inches 24 ± 1.5 inches

Height Overall 51 in. 63 in. 60 in.

Rated Capacity 100,000 gallons 130,000 gallons 180,000 gallons

Cullneu®

Rated Service Flow 2.7 gpm 4.0 gpm 6.0 gpm

@ Pressure Drop @ 3.0 psi @ 4.0 psi @ 5.0 psi

Drain Flow, Maximum33.5 gpm 6.0 gpm 6.0 gpm

pH Limitation* 5.8 - 6.2 5.8 - 6.2 5.2 - 6.8

Recharge Time480 min. 80 min. 30 min.

Recharge Water Consumption, Av.553 gal. 83 gal. 110 gal.

Cullneu Media Volume 1.0 cu. ft. 1.5 cu. ft. 1.6 cu. ft.

Freeboard211 ± 1 inches 21 ± 1 inches 18 ± 1.5 inches

Height Overall 51 in. 63 in. 60 in.

1 Bottom of tank to top of tank ﬁttings.

2 Backwash at 120 psi line pressure.

3 Backwash at 120 psi line pressure.

4 Factory setting.

5 At factory setting and 120 psi line pressure.

6 Top of media to back top edge of port openings.

* Under dynamic conditions, it may be necessary to mix ﬁve parts Cullneu with one part Cullneu C to effectively

raise the pH. The combination of Cullneu and Cullneu C is not certiﬁed by WQA.

Specifications

Filtr-Cleer®

The Filtr-Cleer Automatic Water Filter is capable of reducing particulate matter down to 10 microns

particle size. It will not remove color, organics, colloidal turbidity or dissolved solids. Some

applications follow:

• Reduction of suspended matters in any water system.

• Reduction of particulate matter, such as clay, mud, etc.

• Preﬁltration of oxidized iron ahead of an automatic or manual softener.

• Reduction of light sand.

NOTE: If sands cannot be reduced from the Filtr-Cleer tank during backwashing, a sand trap

should be installed.

• After the retention tank when a Cul-Cleer®system is used to correct hydrogen sulﬁde or colloidal

suspension problems.

The quality and number of gallons ﬁltered water between backwashes will depend upon the amount,

type, and size of the particulate matter being ﬁltered. If a water sample is sent to our laboratory,

where application of a Filtr-Cleer unit is contemplated, write “Filtr-Cleer Analysis” on the sample

tag. Send an additional sample of water for a standard water analysis. The laboratory will test for

Nephelometric Turbidity Units (NTU) and suspended solids (mg/L). The sample will also be ﬁltered

through 10 micron ﬁlter paper and NTU run on a ﬁltered sample. If the NTU of the raw water exceeds

150, suspended solids exceed 150 mg/L or the ﬁltered water through the 10 micron ﬁlter paper is of

an unacceptable quality, a Filtr-Cleer ﬁlter may not be applicable. As a guide, the U.S. Public Health

Drinking Water standards states the turbidity should not exceed 1 NTU. The exact number of gallons

ﬁltered between backwashes cannot be given because of many variables.

Cullar®Filter

Medallist Water Filter with Cullar Media will reduce chlorine taste and odor and other common bad

tastes and odors, and will also reduce most objectional organic colors. It will not remove hydrogen

sulﬁde. It is important to note that whenever the cause of an objectionable taste or odor has not been

established, Health Authorities should determine if water is safe to drink. If bacterial contamination is

present, a Cul-Cleer system is indicated. Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after the system.

Cullneu®Filter

Medallist Water Filter with Cullneu Media will neutralize slightly acid water (pH of 5.8 - 6.2) and thus

help to prevent unsightly brown or green stains due to corrosion of household plumbing. If the pH is

from 5 to 6, one part of Cullneu C media should be mixed with 5 parts of Cullneu media to provide

additional neutralizing capability. If the water to be treated has a pH less than 5, a high hardness, or

a high carbon dioxide level, Cullneu may not be applicable; a solution feeder should be used. Since

Cullneu adds hardness, it should be used prior to a softener.

In order to size and apply the equipment correctly, a complete analysis of the water supply should be

obtained. This can best be accomplished by contacting your local Culligan dealer, who will be able

to test the water supply right at the site, or arrange to have one or more water samples sent to the

Culligan laboratory for a more detailed analysis.

Introduction

Power Loss

The AccuSoft®circuit board is equipped with a Hi-Cap Capacitor and EEPROM memory chip. The

capacitor is capable of maintaining the time, for at least two days, in the event of a power outage.

The EEPROM ensures that the individual programming parameters of your ﬁlter are not lost.

If the power outage lasts long enough to drain the Hi-Cap Capacitor, the control will ﬂash “12:00 PM”

when power is returned to the control. The unit will continue to keep time from the moment power is

restored, and will initiate a full regeneration at the preset regeneration time. The time of day will need

to be reset in order to return the regeneration to its preset time.

If you live in an area where power outages occur with a regular frequency, a battery backup option

is available for ensuring that the time of day is properly maintained. Contact your Culligan Dealer for

more information.

Regeneration

To initiate a regeneration at the preset time, press the “REGEN” button. The “REG” light will light. To

initiate an immediate regeneration, press and hold the “REGEN” button for at least ﬁve seconds. The

“REG” will light and blink. An immediate regeneration will also occur if a power outage has lasted

for more than three hours and the Immediate Regeneration option is chosen. Ask your Culligan Dealer

about this feature.

A regeneration at the Time of Regeneration will occur if so signaled by the Soft-Minder meter. The

“REG” enunciator on the display will also be lit.

Service

The Culligan Medallist Series® water ﬁlter is equipped with a self diagnostic program to insure

optimal operation of your water ﬁlter. Should service become necessary, a phone icon will appear

in the display. If this condition occurs, call your local Culligan Dealer for assistance. The phone icon

and error code will be the only items displayed when service is required on the control.

Familiarization

Programming

The timer uses four buttons:

Button Description

Set-up / Enter Key (Status) Advance timer through display options

Regeneration Key (REGEN) Initiate a regeneration

Toggle Down Key (“-”) Decrease the setting

Toggle Up Key (“+”) Increase the setting

Time of Day

This setting is used to program the current time

of day. When in this step the display will rst

show “tod” for two seconds.

After “tod” is displayed, “12:00 PM” will display

(or the current set time if already programmed)

and the minutes will ash.

• The minutes are adjusted with the

“+” or “-” key until the correct value is

displayed.

• Press the “Regen” key to ash the

hours. Adjust with the “+” or “-” key

until the correct time is displayed.

Pressing the “Status” key will move to the next

programming step. Pressing “Regen” will move

back to the minutes adjust.

Time of Regeneration

This setting is used to program the time at

which a regeneration is to occur in the delay

mode, or in immediate mode with time clock

backup on. The display will rst show “tor” for

two seconds.

After “tor” is shown the display will then

show the default of 2:00 AM (or the current

programmed time of regeneration if already

set). The time can be adjusted in 30 minute

increments by pressing the “+” or “-” keys.

Pressing the “Status” key will save the setting

and move to the next programming step.

Backwash Time

This setting is used to program the cycle 1 time that

is usually backwash. The time of the cycle is kept in

minutes. The display will show “buu” in the display

for two seconds and then the cycle time in the right

most digits. Adjust the value with the “+” or “-” keys.

Pressing the “Status” key will save the setting and

move to the next programming step.

Settline Time

This setting is used to set the time in minutes for cycle

2. This cycle is a settling time for lters. The display will

show “br” in the left most digits and the cycle time in the

right most digits. Adjust the value with the “+” or “-” keys.

Pressing the “Status” key will save the setting and move

to the next programming step.

Fast Rinse Time

This setting is used to set the time in minutes for cycle 3.

The display will show “Fr” in the left most digits and then

the cycle time in the right most digits. Adjust the value

with the “+” or “-” keys. Pressing the “Status” key will save

the setting and move to the next programming step.

Regeneration Interval

This setting is used to set the days between

regeneration in time clock mode. The display will

show “REG” icon and “dAY” for two seconds and then

display the numbers to change. Adjust the value with

the “+” or “-” keys.

Pressing the “Status” key will save the setting and

move to the next programming step.

Blank Display

After the last programming menu is displayed (menu will vary depending on mode of

operation), pressing status will move to a blank display screen.

From the ‘blank display’, pressing the “+” key from the blank display will enter the diagnostics menu.

From the ‘blank display’, pressing the “-” key will enter the statistics menu.

From the ‘blank display’, pressing the “Status” key will exit programming mode and return to the

service mode time display.

The “regen” key is ignored while in the ‘blank display’.

Hidden Programming Menu

Programming

(cont.)

Programming

(cont.)

The Culligan Medallist Series Filter is equipped with an advanced error detection system. During

all operating modes the ﬁlter’s electronics are performing self-diagnostics to ensure that the unit is

operating correctly. There may be times, however, when something may occur that could cause the

unit to improperly operate. In those instances the microprocessor will identify the exact problem and

alert the user with a telephone handset symbol in the upper left corner of the display and the error

code will be shown. Shown below is codes that would appear if an error is detected.

Display Error Description Response

E1 Motor will not stop turning Call Culligan service technician

E2 Motor stuck Call Culligan service technician

E3 Wrong position Call Culligan service technician

If an error code appears that requires an authorized service technician please contact your local

Culligan Dealer.

For any additional troubleshooting or service needs please contact your local Culligan Dealer.

If you unexpectedly experience problem water, make these simple checks before calling your Culligan

dealer. One of the following conditions may be the reason for your interruption of service.

Important

If any of the following conditions is found, the water ﬁlter should be manually recharged according to

instructions on page 6 after you have corrected the problem.

Power Supply

Check your power supply cord. Is it plugged fully into the electric outlet? Be certain that the outlet is

not controlled by a wall switch which has been turned off. Reset conditioner to proper time of day and

then plug in.

Blown Fuse

Check the house fuse or circuit breaker panel. Replace a blown-out fuse or reset an open circuit

breaker.

Power Failure

Any interruption in your power supply or time changes - such as daylight savings - will disrupt your

ﬁlter’s recharge schedule by causing the timer to run off-schedule. Reset timer to proper time of day.

Bypass Valves

Check to see if they are in the proper position. Cul-Flo-Valv®Bypass, if used, should be in the “Service”

(handle stem screwed out) position. If hand valves are used, see that inlet and outlet valve are opened

and that the bypass valve is closed.

No Water

If you aren’t getting any water ﬂow at all, make sure your water supply is working. Open a tap

ahead of the ﬁlter (outside tap) to see if you have any water pressure. If you have water pressure,

check the bypass valve. If it is in the Service position, put it into the bypass and call your Culligan

dealer for service.

Increased Usage

Guests, family additions, new water-using appliances, etc., all will result in more water usage and will

require more capacity from your ﬁlter. You can reprogram your recharging schedule by following the

directions on pages 7 and 8. Call your Culligan dealer for advice and save a service call.

Things to

Check Before

You Call For

Service

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Culligan Wasserfiltersystem Handbücher

Culligan

Culligan US-600A Bedienungsanleitung

Culligan

Culligan WH-HD200-C Bedienungsanleitung

Culligan

Culligan SILVER SERIES Bedienungsanleitung

Culligan

Culligan RVF-10 Bedienungsanleitung

Culligan

Culligan Mark 100 Bedienungsanleitung

Culligan

Culligan Drinking Water System Bedienungsanleitung

Culligan

Culligan Aqua-Cleer Bedienungsanleitung

Culligan

Culligan Iron-Cleer Bedienungsanleitung

Culligan

Culligan RV-EZ Bedienungsanleitung

Culligan

Culligan 9" Bedienungsanleitung

Culligan

Culligan FM-25 Bedienungsanleitung

Culligan

Culligan 9" Handbuch

Culligan

Culligan AQUA-CLEER BXL Series Bedienungsanleitung

Culligan

Culligan AC-30 Premier Bedienungsanleitung

Culligan

Culligan Iron-Cleer Bedienungsanleitung

Culligan

Culligan US-DC1 Bedienungsanleitung

Culligan

Culligan Mark 59 Bedienungsanleitung

Culligan

Culligan Iron-Cleer Datenblatt

Culligan

Culligan Smart Controller HE DF 12 Bedienungsanleitung

Culligan

Culligan FM-5 Bedienungsanleitung

Culligan

Culligan FM 15 Bedienungsanleitung

Culligan

Culligan GOLD SERIES Bedienungsanleitung

Culligan

Culligan Medallist Plus Sulfur-OX3 Bedienungsanleitung

Culligan

Culligan FM-15A Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung