CYP CMSDI-1616S Bedienungsanleitung

CMSDI-1616S

16×16 3G-SDI Hybrid Modular Matrix

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

Never spill liquid of any kind on or into this product.

Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts inside

the unit.

Do not attach the power supply cabling to building surfaces.

Use only the supplied power supply unit (PSU). Do not use the PSU if it is

damaged.

Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

VR0 21/01/13 Preliminary Release

VS1 11/03/13 Updated format/diagrams

CONTENTS

1. Introduction............................................ 1

2. Applications........................................... 1

3. Package Contents ................................ 1

4. System Requirements............................ 1

5. Features.................................................. 2

6. Operation Controls and Functions....... 3

6.1 Front Panel ........................................3

6.2 Rear Panel.........................................5

6.3. Remote Control...............................6

6.4 RS-232 Protocols ...............................7

6.5 Assign IP Address..............................7

6.6 RS-232/Telnet Commands...............8

6.7 Telnet Control ...................................9

6.8 Web GUI Control ............................11

7. Specications ...................................... 12

8. Connection Diagram .......................... 15

9. Acronyms ............................................. 17

1. INTRODUCTION

This 16×16 3G-SDI Hybrid Modular Matrix can switch and distribute up

to sixteen SDI sources to any sixteen SDI sinks, providing bandwidth

up to 2.970 Gb/s for 3G-SDI video support. In addition, this matrix also

features IP control allowing users to access and control the matrix

remotely.

2. APPLICATIONS

• Video broadcasting system switching and display

• Professional video editing suite switching and display

• Film studio program monitoring

• Airport or industrial security monitoring system

3. PACKAGE CONTENTS

• 16×16 3G-SDI Hybrid Modular Matrix

• Power Cord

• Remote Control (CR-119 with Battery)

• Operation Manual

4. SYSTEM REQUIREMENTS

SDI source equipment such as an SDI camera and output SDI monitor

or recording device with recommended SDI connection cables.

5. FEATURES

• Supports operation at 2.970 Gb/s, 2.970/1.001 Gb/s, 1.485 Gb/s,

1.485/1.001Gb/s, and 270 Mb/s

• Supports SDI input/output modes:

- SD-SDI (SMPTE 259M-C, at bitrates of 270 Mbit/s)

- HD-SDI (SMPTE 292M, at bitrates of 1.485Gbit/s and 1.485/1.001 Gbit/s)

- 3G-SDI (SMPTE 424M/425M-A and B, at bitrates of 2.970 Gbit/s and

2.970/1.001 Gbit/s)

• Signal equalized and re-clocked to improve signal transmission

distances

• Supports signal input and output distances of up to 250 m for SD

signals, 200 m for HD signals and 100 m for 3G signals

• Supports audio sampling rate at 48 kHz

• Connects with other units to extend your signal over longer distances

• 3U rack mountable design

Note: The unit was tested with Belden 1694A cable, results may vary

with cables of a different specication.

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

POWERRETURN7 89

456

LOCK

SAVE

123RECALL

0ENTER OUT/IN

ALL

PAGE

STANDBY

LOCK

DIGITAL MATRIX SWITCHER

106431 9 11 12 16

137 852

1LCM: Displays the Menu and the setting information of each input

and output selection.

2STANDBY LED: This LED will illuminate when unit is in 'Stand-by

Mode'.

3LOCK LED: This LED will illuminate when the key lock function is

active.

4IR Window: IR Receiver window (accepts the remote control signal

of this device only).

5POWER: Press this button to power the device on/off.

6PAGE ▲◄►▲: Use these buttons to display the current Input/

Output settings status or to navigate the settings menu.

7RETURN: Press this button to go back/exit the current selection.

8MENU: Press this button to enter the settings menu. There are total

of 9 functions available.

- Firmware version

- IP Address: Use this address for logging into Telnet and the Web

GUI

- DHCP/AUTO IP ON/OFF (ON: DHCP enable, OFF: Static IP enable)

- STATIC IP

- STATIC NETMASK Setting

- STATIC GATEWAY Setting

- In Slot Info.

- Out Slot Info.

- Exit

9ENTER: Press to conrm the setting or selection.

10 0~9: Press to select the input or output ports.

11 OUT/IN: Press this button to select the which source (Input) to show

on which display (Output). Press 'OUT/IN', then select the desired

output using the number buttons (use the '+' button to add further

outputs if required or 'ALL' to assign all outputs to the same source),

then press 'OUT/IN' again to then select which source you wish

assign.

Note: Only a single source can be selected at any one time but

multiple outputs can be assigned to a source.

12 +: Press this button when selecting more than one output for a

source. (This button is only functional in when in Input/Output

entry mode)

13 LOCK: Press and hold this button for 3 seconds to lock all the front

panel buttons to prevent accidental button presses. The Lock

LED will illuminate, to unlock press and hold the button again for 3

seconds.

14 SAVE: Press this button to save the present Input/Output settings.

There are 10 sets available for saving.

15 RECALL: Press this button to recall the saved Input/Output settings

(1~10).

16 ALL: Press this button to directly assign all outputs to the same input.

6.2 Rear Panel

9 12

-9 12

13 16

-13 16

INPUT

100-240VAC

50/60 Hz

1 4

INPUT

5 8

INPUT INPUT OUTPUTOUTPUT

1 4

OUTPUT OUTPUT

5 8

RS232

CONTROL

4 76

1INPUT 1~16: Connect up to 16 SDI equipped source devices such

as digital cameras or video players with SDI cables.

2OUTPUT 1~16: Connect up to 16 SDI equipped sink devices such

as displays (TV/monitors) or broadcast video recorders with SDI

cables.

3RS-232: Connect to a PC or RS-232 control system with D-Sub 9-pin

cable to control the unit with RS-232 commands (See Section 6.6

for RS-232 commands).

4CONTROL: This port is the link for Telnet and Web GUI controls,

connect to an active Ethernet link with an RJ45 terminated cable

(for further details, please refer to sections 6.7 and 6.8).

5POWER Switch: Use this switch to power the device ON(I) or OFF(O),

when the power is switched ON the device will automatically

power up.

6Power Supply: Plug the power cord to an AC wall outlet for power

supply.

7Ventilation Fan: This fan will automatically activate when the

device is switched ON. Do not block or cover this port. Please

allow adequate space around the unit for air to circulate.

Inhaltsverzeichnis

Andere CYP Matrix-Umschalter Handbücher

CYP

CYP SM-2X4-HDMI-LC Bedienungsanleitung

CYP

CYP PU-8H8HBTPL Bedienungsanleitung

CYP

CYP CDPS-44SM Bedienungsanleitung

CYP

CYP CMSI-8H8HS Bedienungsanleitung

CYP

CYP OR-HD88S Bedienungsanleitung

CYP

CYP PUV-1082-4K22 Bedienungsanleitung

CYP

CYP HDBT PU-4H4HBTE-4K Bedienungsanleitung

CYP

CYP PU-424HBTL-KIT Bedienungsanleitung

CYP

CYP CMLUX-44S Bedienungsanleitung

CYP

CYP CMPRO-UA8H8CVPL Bedienungsanleitung

CYP

CYP PU-424HBTE Bedienungsanleitung

CYP

CYP CDPS-44SM Bedienungsanleitung

CYP

CYP CPLUS-V4H2HPIP Bedienungsanleitung

CYP

CYP PU-16H8HBT Bedienungsanleitung

CYP

CYP OR-HD88S Bedienungsanleitung

CYP

CYP EL-41S-4K Bedienungsanleitung

CYP

CYP PU-8H8HBTE-4K Bedienungsanleitung

CYP

CYP PUV-1210PL-RX Bedienungsanleitung

CYP

CYP CMSI-8H8CV Bedienungsanleitung

CYP

CYP CMPRO-U4H4CVPL Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

CYP

CYP Elpro Video Labs CDPS-UC4H4HFS Bedienungsanleitung

CYP

CYP CPLUS-1082CVEA Bedienungsanleitung

CYP

CYP OR-44-4K22 Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte

Lindy

Lindy 38042 Bedienungsanleitung