CYP PRO-F32M Bedienungsanleitung
3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer file, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 12/02/2019 First release
5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................7
5. Features..................................................7
6. Operation Controls and Functions.......8
6.1 Front Panel................................................... 8
6.2 Rear Panel..................................................... 9
6.3 Remote Control.......................................... 9
6.4 IR Cable Pin Assignments .....................10
6.5 RS-232 Protocol........................................10
6.6 RS-232 and Telnet Commands............11
6.7 Telnet Control............................................14
6.8 WebGUI Control .......................................15
7. Connection Diagram .......................... 21
7.1 HDMI Switching .......................................21
7.2 Fiber Extension.........................................22
8. Specifications...................................... 23
8.1 Technical Specifications ........................23
8.2 Video Specifications................................24
9. Acronyms............................................. 25
6
1. INTRODUCTION
This 3×2 HDMI and Fiber Matrix allows customer to route up to three
HDMI input signals (two 18Gbps HDMI and one 10.2Gbps HDMI over
optical fiber) to any of two HDMI outputs (one 18Gbps HDMI and one
10.2Gbps optical fiber). The optical fiber input and output both support
transmission distances up to 300 metres and use paired LC connectors.
This unit supports resolutions up to 4K@60Hz (4:4:4, 8-bit), 16-bit Deep
Colour up to 1080p@60Hz, HDR (High Dynamic Range), HD audio formats
and other features defined by the HDMI 2.0 specification. HDMI sources
with bandwidth higher than 10.2Gbps are automatically chroma and/
or bit-depth subsampled for transmission over the fiber output. Six pre-
defined internal EDIDs and two external EDID selections are available for
EDID management. The unit provides intuitive front panel controls as well
as RS-232, Telnet, WebGUI and IR remote control options.
2. APPLICATIONS
Entertainment Rooms & Home Theatres
Showrooms & Demo Rooms
Lecture Hall Presentations
Public Commercial Displays
3. PACKAGE CONTENTS
1×3 by 2 HDMI and Fiber Matrix
1×Remote Control (CR-155)
1×IR Extender Cable
1×3.5mm to 9-pin D-sub Adapter
1×5V/2.6A DC Power Adaptor
1×Operation Manual
7
4. SYSTEM REQUIREMENTS
HDMI source equipment such as media players, video game consoles
or set-top boxes.
HDMI receiving equipment such as HDTVs, monitors or audio
amplifiers.
The use of “Premium High Speed HDMI”cables is highly
recommended.
Use of the optical fiber input/output requires a second unit and
appropriate paired LC multi-mode fiber in a crossover configuration.
5. FEATURES
HDMI with 3D & 4K@60Hz with HDR support
DVI 1.0 compliant with the use of an HDMI-DVI adaptor
HDCP 2.2 and 1.x compliant
Supports HD resolutions up to 3840×2160@60Hz (4:4:4, 8-bit) &
4096×2160@60Hz (4:4:4, 8-bit)
Supports 16-bit Deep Colour up to 1080p@60Hz
2×HDMI (18Gbps) and 1×HDMI over fiber (LC pair, 10.2Gbps) inputs
1×HDMI (18Gbps) and 1×HDMI over fiber (LC pair, 10.2Gbps) outputs
HDMI sources with bandwidth higher than 10.2Gbps are automatically
chroma and/or bit-depth subsampled for transmission over the fiber
outputs
Fiber transmission distances of up to 300m
3×2 matrix routing between all inputs and outputs
Supports pass-through of audio formats: LPCM 2.0/5.1/7.1, Bitstream,
and HD Bitstream
Comprehensive EDID management support including 6 pre-defined
internal EDIDs and 2 external EDIDs
Supports control via front panel, WebGUI, Telnet, RS-232, and IR
remote
8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
SERVICE POWER 123
OUT A
123
OUT B
PRO-F32M
1 2 3 4 5 6
1SERVICE: This slot is reserved for firmware update use only.
2IR WINDOW: Accepts IR signals from the included IR remote for
control of this unit only.
3POWER LED: This LED will illuminate green to indicate the unit is on
and receiving power. When the unit is in stand-by mode the LED will
illuminate red.
4POWER BUTTON: Press this button to power the unit on or place it
into stand-by mode.
Note: Ethernet, IR and RS-232 remain active while the unit is in stand-by
mode.
5OUT A BUTTON & LEDs: Press this button to sequentially switch
through the 3 available inputs, and mute, for Output A. The LEDs will
illuminate to indicate the currently selected input for Output A. When
all 3 LEDs are blinking, the output is muted.
6OUT B BUTTON & LEDs: Press this button to sequentially switch
through the 3 available inputs, and mute, for Output B. The LEDs will
illuminate to indicate the currently selected input for Output B. When
all 3 LEDs are blinking, the output is muted.
9
6.2 Rear Panel
DC 5VIR INRS-232
CONTROL
FIBER A HDMI B
OUT
FIBER 3
HDMI 2HDMI 1
IN
1 2 3 4 5 6
1FIBER A & HDMI B OUT: Connect the HDMI output to HDMI TVs,
monitors or amplifiers for digital video and audio output. DVI displays
are supported with the use of an HDMI to DVI adapter. Connect the
fiber (paired LC) output to the fiber input on a second unit.
2HDMI 1~2 & FIBER 3 IN: Connect the HDMI inputs to HDMI source
equipment such as media players, game consoles or set-top boxes.
DVI sources are supported with the use of an HDMI to DVI adapter.
Connect the fiber (paired LC) input to the fiber output from a second
unit.
3CONTROL: Connect directly, or through a network switch, to your PC/
laptop to control the unit via Telnet/WebGUI.
4RS-232: Connect, via the provided 9-pin adapter cable, to a PC, laptop
or other serial control device to send RS-232 commands to control the
unit.
5IR IN: Connect to the provided IR Extender to extend the IR control
range of the unit. Ensure that the remote being used is within direct
line-of-sight of the IR Extender.
6DC 5V: Plug the 5V DC power adapter into the unit and connect it to
an AC wall outlet for power.
6.3 Remote Control
1POWER: Press this button to power the unit on or
place it into stand-by mode.
2A1~A3 & B1~B3: Press any of these buttons to switch
immediately to the corresponding input for the
specified output (A or B).
Note: A4 & B4 have no function with this unit.
CR-155
POWER
1
2
3
4
1
2
3
4
BA
2
1
10
6.4 IR Cable Pin Assignments
3
1
2
IR Signal
Power
Ground
IR Extender
6.5 RS-232 Protocol
UNIT
►
◄
REMOTE SYSTEM
Pin Definition Pin Definition
1 NC 1 NC
2TxD 2 RxD
3 RxD 3 TxD
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 115200bps
Data Bits: 8
Parity Bits: None
Stop Bits: 1
Flow Control: None
Inhaltsverzeichnis
Andere CYP Matrix-Umschalter Handbücher
CYP
CYP EL-42M-PIP Bedienungsanleitung
CYP
CYP CMSI-8H8HC Bedienungsanleitung
CYP
CYP CMSI-8H8CVL Bedienungsanleitung
CYP
CYP OR-32USBC-4K22 Bedienungsanleitung
CYP
CYP CPLUS-V4H2HPIP Bedienungsanleitung
CYP
CYP SM-4X2-HDMI-LC Bedienungsanleitung
CYP
CYP PU-424HBTE Bedienungsanleitung
CYP
CYP CMPRO-U4H4CVPL Bedienungsanleitung
CYP
CYP SM-2X2-HDMI-LC Bedienungsanleitung
CYP
CYP OR-44VWC Bedienungsanleitung
CYP
CYP PUV-44XPL-AVLC Bedienungsanleitung
CYP
CYP PU-8H8HBTPL Bedienungsanleitung
CYP
CYP OR-42CD-4K22 Bedienungsanleitung
CYP
CYP CPLUS-V4H4H Bedienungsanleitung
CYP
CYP OR-HD44E Bedienungsanleitung
CYP
CYP CMIR-882 Bedienungsanleitung
CYP
CYP EL-41S-4K Bedienungsanleitung
CYP
CYP Elpro Video Labs CDPS-UC4H4HFS Installationshandbuch
CYP
CYP CPLUS-V4H2HA Bedienungsanleitung
CYP
CYP PU-8H8HBTPL-4K22 Bedienungsanleitung
