D-Link AC1200 Bedienungsanleitung

Additional documentation is also available on the D-Link website

DAP-3666

Quick Installation Guide

Nuclias Connect AC1200 Wave 2 Outdoor Access Point

LAN2 LAN1(PoE)

DAP-3666 Quick Installation Guide 1

ENGLISH

• Internet Explorer 11, Safari 7, Firefox 28,

or Google Chrome 33 and above (for

conﬁguration)

Hardware Overview

LED Indicators

LAN2 LAN1(PoE)

Figure 1: Front Panel LED

# LED Description

1Power/

Status

Green (Solid) - Device operational

Red (Flashing) - Device booting

up/Device malfunctioned

Red (Solid) - Device boot up

has failed

Table 1: LED Description

Interface Connectors

LAN2 LAN1(PoE)

Figure 2: Bottom Connectors

# Connector Description

1Mounting

Lock

Connector for the mount screw.

2 Reset Press and hold for 10 seconds to

factory reset the device.

3 LAN2 Port Gigabit RJ-45 port for data.

Before You Begin

This installation guide provides instructions

for installing the DAP-3666 on your network.

Additional documentation is also available on

the D-Link support website.

• Nuclias Connect Manual: For additional

information and instructions on how

to configure the device using Nuclias

Connect.

• DAP-3666 User Manual: For additional

information and instructions on how to

conﬁgure the device using the web user

interface.

Package Contents

This DAP-3666 package includes the following

items:

• DAP-3666 Access Point

• Mounting Plate and Hardware

• Grounding Wire

• Quick Start Guide

• Mounting kit (Wall/Pole Mount)

- Stainless steel mount base x 1

- Stainless tie back straps x 2

- Wall screw x 4

- Wall plug x4

- Stainless mount screw (hexagonal hole) x1

If any of the above items are damaged or

missing, please contact your local D-Link reseller.

Note: To power the unit, use an 802.3af or

802.3at PoE Switch or PoE Injector.

System Requirements

• Computers with Windows®, Macintosh®,

or Linux-based operating systems with an

installed Ethernet Adapter

1 2 3 4

2DAP-3666 Quick Installation Guide

ENGLISH

# Connector Description

4LAN1(PoE)

Port

Gigabit RJ-45 port for data and

Power over Ethernet (PoE) power.

Table 2: Interface Description

LAN2 LAN1(PoE)

Figure 3: Rear Connectors

# Connector Description

1Grounding

Wire

Connector for the grounding wire.

2Wall/Pole

Mount

Mount to connect to the mounting

plate on a wall or a pole.

Table 3: Interface Description

Installation

Using Power over Ethernet (PoE)

1. Use a standard Ethernet cable to connect

the LAN1(PoE) port on the DAP-3666

to a PoE power source device such as

an 802.3af or 802.3at PoE switch or PoE

injector.

Conguration

Using Nuclias Connect

The DAP-3666 is designed to be managed

through Nuclias Connect. Refer to the Nuclias

Connect Manual for detailed configuration

instructions.

Note: D-Link recommends manually conﬁguring

the device before mounting it.

Nuclias Connect App Conguration

1. Download the free Nuclias Connect app

from the App Store or Google Play by

searching for Nuclias Connect or by

scanning the QR code below.

2. Open the Nuclias Connect app and follow

the onscreen instructions to discover and

set up your device.

Manual Conguration

Note:The management computer, DHCP server

and DAP-3666 must be in the same subnet.

Use one of the following methods to access the

web user interface:

Connecting through Ethernet

1. Use an Ethernet cable to connect the

DAP-3666 to the management computer,

or to the switch or router the management

computer is connected to.

DAP-3666 Quick Installation Guide 3

ENGLISH

2. Manage the access point from a computer.

Enter dap3666.local in the address ﬁeld

of your browser.

3. Log in to the administration user

interface. The default login information is

Username: admin

Password: admin

Connecting Wirelessly

1. Connect the management computer to

the default SSID of the DAP-3666, “dlink”.

2. Manage the access point from a computer.

Enter dap3666.local in the address ﬁeld

of your browser.

3. Log in to the administration user

interface. The default login information is

Username: admin

Password: admin

Mounting

Figure 4: LAN Port Waterproof Enclosure

1. Connect an Ethernet Cable to the

LAN1(PoE) port on the DAP-3666. Use

the LAN Port Waterproof Enclosures to

seal the ports.

Mounting on a Pole

Figure 5: Attaching the Mounting Plate

1. Secure mount base to the pole with the

two stainless tie back strap sets. Ensure

that the tie back is locked securely.

Figure 6: Mounting the Device

2. Align and slide the DAP-3666 down so

that the mounting plate securely locks to

the DAP-3666.

Gland Sealing

Nut Sealing

4DAP-3666 Quick Installation Guide

ENGLISH

Mounting on a Solid Wall

Figure 7: Attaching the Mounting Plate

1. Use the mounting plate to mark the

location where to drill the holes in the wall.

2. Drill holes on the markings and place the

included anchors into the drilled holes.

3. Align and place the mounting plate on top

of the anchors and use the included screws

tosecure the mountingplateto the surface.

Figure 8: Mounting the Device

4. Align and slide the DAP-3666 down so

that the mounting plate securely locks to

the DAP-3666.

Securing the Mount Screw and

Connecting the Grounding Wire

Figure 9: Attaching the Mount Screw

1. Use the included mount screw (hexagonal

hole) to lock the DAP-3666 to the pole/

wall mount.

Figure 10: Securing the Mount Screw

2. With the included hexagon socket

spanner, tighten the mount screw until

the DAP-3666 is secured.

TECHNICAL SUPPORT dlink.com/support

DAP-3666 Quick Installation Guide 5

ENGLISH

Figure 11: Attaching the Grounding Wire

3. A grounding wire is to protect your device

from lightning strikes and the buildup of

static electricity. Attach the grounding

wire to the DAP-3666 using the included

screw(M3.9 * 7.8 mm).

Figure 12: Attaching the Grounding Wire

4. Tighten the grounding wire (green-and-

yellow, 18AWG) to the DAP-3666 until it is

securely attached.

Figure 13: Attaching the Grounding Wire

5. Attach the other end of the grounding

wire to either the wall or pole mount.

Ensure that the wall or pole mount is

connected to an electrical ground.

ErP Power Usage

This device is an Energy Related Product (ErP) that automatically switches to a power-saving Network

Standby mode within 1 minute of no packets being transmitted. It can also be turned oﬀ through a power

switch to save energy when it is not needed.

Network Standby: 5.84 watts

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by

one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

• Any changes or modiﬁcations not expressly approved by the party responsible for compliance could

void the user’s authority to operate this equipment.

• This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

Appendix - Statements

6DAP-3666 Quick Installation Guide

ENGLISH

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator & your

body.

Note: The country code selection is for non-US model only and is not available to all US model. Per FCC

regulation, all WiFi product marketed in US must ﬁxed to US operation channels only.

Déclaration d’exposition aux radiations

Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 0.28 m de

distance entre la source de rayonnement et votre corps.

VCCI-A Warning

警告使用者:

此為甲類的資訊技術設備，在居住環境中使用時，可能會造成射頻擾動，在這種情況下，

使用者會被要求採取某些適當的對策。

Product and Warranty Information

To ﬁnd out more about D-Link Nuclias product or marketing information, please visit the website http://

www.dlink.com or https://www.nuclias.com.

The D-Link Limited Lifetime Warranty information is available at

http://www.dlink.com/warranty

1. Instructions for the installation of that conductor to building earth by a SKILLED PERSON.

2. Please contact the authorized distributor of D-Link for related accessories (Outdoor interconnection

cable, Cable Gland, Cable, etc.) for purchase and installation.

この装置は、クラスA機器です。この装置を住宅環境で使用すると電

波妨害を引き起こすことがあります。この場合には使用者が適切な対

策を講ずるよう要求されることがあります。

VCCI-A

DAP-3666 Quick Installation Guide 7

ENGLISH

8DAP-3666 Quick Installation Guide

ENGLISH

Industry Canada statement

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage

préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de

provoquer un fonctionnement indésirable.

• This Class A digital apparatus complies with Canadian ICES-003.

• Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

• This device and its antenna(s) must not be co-located or operating in conjunction with any other

antenna or transmitter, except tested built-in radios.

• Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une autre

antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées.

• The County Code Selection feature is disabled for products marketed in the US/ Canada.

• La fonction de sélection de l’indicatif du pays est désactivée pour les produits commercialisés aux États-

Unis et au Canada.

Caution :

(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain

compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.

Avertissement:

(iv) lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les numéros de modèle de l’antenne et les

pires angles d’inclinaison nécessaires pour rester conforme à l’exigence de la p.i.r.e. applicable au masque

d’élévation, énoncée à la section 6.2.2.3, doivent être clairement indiqués

Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with greater than 21 cm between the radiator & your body.

Déclaration d’exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 21 cm entre le radiateur et

votre corps.

Andere Handbücher für AC1200

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere D-Link Drahtloser Zugangspunkt Handbücher

D-Link

D-Link DWL-6600AP Bedienungsanleitung

D-Link

D-Link AirPremier N DAP-2555 Bedienungsanleitung

D-Link

D-Link DWL-2200AP - AirPremier - Wireless Access... Bedienungsanleitung

D-Link

D-Link AirPremier N DAP-2310 Bedienungsanleitung

D-Link

D-Link DWL-3140AP - Web Smart PoE Thin Access Point Bedienungsanleitung

D-Link

D-Link AirPro DWL-5000AP Bedienungsanleitung

D-Link

D-Link DWL-2200AP - AirPremier - Wireless Access... Bedienungsanleitung

D-Link

D-Link AirPremier N DAP-2360 Bedienungsanleitung

D-Link

D-Link NUCLIAS CONNECT DAP-2680 Bedienungsanleitung

D-Link

D-Link DIR-505 Bedienungsanleitung

D-Link

D-Link DAP-1160 Bedienungsanleitung

D-Link

D-Link xtreme n duo dap-1522 Bedienungsanleitung

D-Link

D-Link DWL-3200AP - AirPremier - Wireless Access... Bedienungsanleitung

D-Link

D-Link AirPremier N DAP-2360 Bedienungsanleitung

D-Link

D-Link DWL-8500AP Service-Handbuch

D-Link

D-Link DAP-3712 Bedienungsanleitung

D-Link

D-Link DAP-1360L Bedienungsanleitung

D-Link

D-Link DAP-1160 Bedienungsanleitung

D-Link

D-Link DWL-2700AP - AirPremier Outdoor Wireless Access... Bedienungsanleitung

D-Link

D-Link AirPlus XtremeG DWL-2200AP Bedienungsanleitung

D-Link

D-Link DAP-3310 Bedienungsanleitung

D-Link

D-Link myPocket DIR-457 Bedienungsanleitung

D-Link

D-Link AirPlus Xtreme G DWL-2000AP Bedienungsanleitung

D-Link

D-Link DAP-2590 - AirPremier N Dual Band PoE Access... Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung