D-MAX DCC-500F Bedienungsanleitung
Digital Day & Night
COLOR CAMERA
USER MANUAL
The lightning flash with an arrowhead symbol, within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply
with limits for a Class A digital device, pursuant to part 15 of the FCC
Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards : Do NOT
use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes
CAUTION :
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK),
NO USER SERVICEABLE PARTS INSIDE.
REFER WERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
2 3
ContentsWarning
1. Features 4
2. Components & Cable Connection 6
3. Names and functions of parts 7
4. Installation & Dimension 10
5. Setup Menu Operation 16
6. Special Menu operation 27
7. Troubleshooting 36
8. Specifications 38
The camera needs periodic inspection.
Contact an authorized technician for
inspection.
Stop using your camera when you find
a malfunction.
If you use your camera around smoke or
unusual heat for a long time, fire may be
caused.
Do not Install the camera on a surface
that can not support it.
Unless the surface is suitable, it could
cause falling or other hazards.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other
hazards.
Do not use the camera close to a gas
or oil leak.
It may result in fire or other hazards.
Horizontal Resolution 530 TVLines
Clear image quality has been achieved by
employing a SONY CCD with 410,000 (effective)
pixels, which provides a horizontal resolution of
530 TV lines.
DAY & NIGHT
This camera has a function that automatically
selects the mode that is appropriate for daytime or
night-time conditions The COLOR mode operates
in daytime conditions to provide optimum colors,
and BW mode operates in nighttime conditions to
enhance the definition of the image.
Electronic IRIS
The electronic IRIS function enables continuous
automatic control of the shutter between
1/60~1/120,000 seconds.
PRIVACY Function
The PRIVACY function conceals the areas you do
not wish to appear on the screen.
4
High Sensitivity
The built-in high sensitivity SONY COLOR CCD
enables a clear image even in 0.3Lux(0.1Lux
B/W) or as low as 0.002Lux with SENS-UP.
DNR (Digital Noise Reduction)
The amount of low illuminance noise has been
significantly reduced, and the signal-to-noise ratio
(S/N ratio) as well as horizontal resolution have
been improved, resulting in a clear and sharp
image display even in the dark.
Controlled by OSD Menu
The camera can be controlled by selecting text
displayed on the monitor screen.
Additional Functions
SENS-UP, MOTION DETECTION, MIRROR,
SHARPNESS and SYNC (INT/LL) functions are
also available.
5
1. Features
6 7
1) COLOR CAMERA
2) AUTO IRIS LENS
CONNECTION PLUG
3) C-MOUNT ADAPTOR
4) L-WRENCH
5) MANUAL
2. Components
DCC-500F
HIGH RESOLUTION COLOR CAMERA
DAY & NIGHT,DSS
DCC-500F
HIGHRESOLUTION COLOR CAMERA
DAY& NIGHT, DSS
3.
Names and Functions of Parts
1) Front
Lens protection cap
Please cover the lens when not using it.
CS-Mount lens adaptor
Please attach the CS-Mount lens here.
Back Focus clamp screw
Please loosen the clamp screw with a
screwdriver before adjusting the Back Focal
length.
Mounting bracket screw hole
Please use the screw hole
when fixing the camera
onto the mounting
bracket. Please use the
clamp screw as specified picture.
1/4"-20 UNC (20 THREAD)
L:4.5mm 0.2mm (ISO standard),
or 0.197" (ASA standard)
L
Power lamp
Lights up when the correct power is supplied to
the camera.
Setting button
SETUP button : Used for the menu display.
This button can be used to confirm settings
after changing the value of the selected
function or current conditions.
UP & DOWN button : Used for selecting items
by moving the cursor up or down on
the menu screen.
LEFT & RIGHT buttons : Used when
changing item values, by moving the cursor to
the left or right on the menu screen.
Power input terminal
Connects to the power appropriate to each
power requirement.
The mounting bracket can be separated and
attached to the top of the camera.
In this instance please do not tighten the screw
to a depth of more than 5mm, otherwise
serious damage can occur to the inside of the
camera.
2) Back
Auto iris lens connector
This is the connection terminal for the auto iris
lens.
Video output terminal
Sends video signals and connects to the video
input terminal of the monitor.
8 9
¶
- Please remove the cover of the auto iris lens
connection plug and solder the lens cable to the
connector pin in the plug.
- Please replace the auto iris lens connection plug
cover and take off the lens protection cap, and
11
1) Lens
Lenses are sold separately. Lenses such as auto
iris lens, CS-Mount lens and C-Mount lens can be
used.
Use of the DC auto iris lens is recommended to
achieve the best results for operating this product
effectively.
Please keep the lens clean.
Any foreign objects and fingermarks on the lens
can cause inferior image quality in low light level
conditions.
When using an auto iris lens
- Please peel off about 8mm of the outer skin of the
auto iris lens cable.
- Please peel off about 2mm of the outer skin of
the insulated conductor inside the lens cable
10
Note
4. Installation
Lens cable
Connector
No.4 Pin
No.2 Pin
No.1 Pin
No.3 Pin
Pin No. LENS
DC VIDEO
No.1 Pin Damping- Red(power)
No.2 Pin Damping+ NC
No.3 Pin Drive+ White(video signal)
No.4 Pin Dreve- Black(GND)
When using a CS-Mount lens
Please take off the lens protection cap and attach
the CS-Mount lens to the camera by screwing it in
clockwise.
When using a C-Mount lens
- Please take off the lens protection cap and attach
the C-mount adaptor.
- Please attach the C-Mount lens to the camera by
screwing it in clockwise.
13
then attach the auto iris lens to the camera by
screwing it in clockwise.
-Please insert the connection plug that is
connected to the auto iris lens cable into the
auto lens connector, which is located on the
back of the camera
- Please set the lens selection switch, located on
the back of the camera, to DC or VIDEO depen-
ding on the type of auto iris lens which is being
used.
12
DCC-500F
HIGH RESOLUTION COLOR CAMERA
DAY& NIGHT, DSS
DCC-500F
HIGH RESOLUTION COLOR CAMERA
DAY& NIGHT, DSS
DCC-500F
HIGH RESOLUTION COLOR CAMERA
DAY& NIGHT, DSS
DCC-500F
HIGH RESOLUTION COLOR CAMERA
DAY & NIGHT, DSS
CS-mount adaptor
C-mount adaptor
Lens protection cap
the type of monitor and accessories.
Please refer to the user's manual for each
instrument.
Please turn off the power when connecting.
3) Connecting to power
DC Power Type (DC 12V, 500mA)
15
Please use the specified lens connection parts as
shown in the picture below.
The use of the wrong sized parts may cause
damage to the inside of the camera or result in
poor fitting.
Use of a lens which is too heavy affects the balance
of the camera and may cause a malfunction.
Please use a lens that weighs less than 450g.
Please select Av mode if possible when adjusting
the automatic light control (ALC) of an auto lens.
Use of PK mode may cause hunting
2) Connecting to a monitor
Please connect the video output terminal located
on the back of the camera to the monitor.
The connection method varies depending on
14
Note
‚·ˇ¯˝
CCD ˜«‚ ¶
Please press the LEFT or RIGHT button if you
wish to change mode.
When the LEFT or RIGHT button is pressed,
available values and modes are displayed in
order. Please keep pressing the button until
you get to the mode you wish to operate.
Please select 'EXIT' and then press the
SETUP button to finish the setting.
If appears at the mode you wish to operate, it
means that there is a sub-menu which can be
selected by pressing the SETUP button.
If appears at the mode item, it means that there is
no mode available to be selected.
2) LENS
This function is used to adjust the brightness of
the screen.
17
1) Settings
Please press the SETUP button Settings can
now be made. The SETUP menu is displayed
on the monitor.
Please select any function you wish to activate
by using the UP and DOWN buttons.
The arrow can be moved up or down by using
the UP and DOWN buttons.
Please position the arrow to point to the
function you wish to operate.
16
5. Setup Menu Operation
SETUP
LENS MNUAL
SHUTTER ESC
WHITE BAL ATM
BACKLIGHT OFF
AGC LOW
DNR LOW
SENS-UP OFF
SPECIAL
EXIT
SETUP
LENS MNUAL
SHUTTER ESC
WHITE BAL ATM
BACKLIGHT OFF
AGC LOW
DNR LOW
SENS-UP OFF
SPECIAL
EXIT
Modes can be
changed using the
LEFT and RIGHT
buttons.
Select any function
you wish to operate
by using the UP
and DOWN
buttons.
Note
Inhaltsverzeichnis
Andere D-MAX Sicherheitskamera Handbücher
D-MAX
D-MAX DCC-520DV Bedienungsanleitung
D-MAX
D-MAX DCC-700d Series Bedienungsanleitung
D-MAX
D-MAX DSC-Se5 Bedienungsanleitung
D-MAX
D-MAX DCC 600d Series Bedienungsanleitung
D-MAX
D-MAX DMS-200 Bedienungsanleitung
D-MAX
D-MAX 650 TVL Bedienungsanleitung
D-MAX
D-MAX DCC-520D series Bedienungsanleitung
D-MAX
D-MAX DWC-540DV Bedienungsanleitung
D-MAX
D-MAX DCC-500D Bedienungsanleitung
D-MAX
D-MAX DHC-10SITA Bedienungsanleitung
D-MAX
D-MAX DCC-500D Bedienungsanleitung
D-MAX
D-MAX DCC-500DV Bedienungsanleitung
D-MAX
D-MAX DMC-20SEC Bedienungsanleitung
D-MAX
D-MAX DSC-2000Si Bedienungsanleitung
D-MAX
D-MAX DCC-580D Series Bedienungsanleitung
D-MAX
D-MAX 680 TVL Bedienungsanleitung
D-MAX
D-MAX DSC-737SE Bedienungsanleitung
D-MAX
D-MAX DWC-540PV Bedienungsanleitung
D-MAX
D-MAX DCC-601DV Bedienungsanleitung
D-MAX
D-MAX DCC-708DV Bedienungsanleitung
