Daewoo BM090 Bedienungsanleitung

D1146 Primary filter:clean at every 5,000km,change at every 15,000km there

Change at every 20,000km. 166Page

Valve clearance Adjust at end of first 1,000km and every 20,000km there after. 171 Page

Air cleaner Clean at every 4,000km, change at every 12,000km there after. 176 Page

Transmission oil Change at end of first 5,000km and every 20,000km there after. 178 Page

Rear axle oil Change at end of first 5,000km and every 20,000km there after. 179 Page

Power steering oil Change at end of first 1,000km and every 24,000km there after. 180 Page

Power steering filter Change at end of first 1,000km and every 24,000km there after. 182 Page

IMPORTANT SERVICE ACTIVITIES

ҧAny failure resulting from a lack of normal maintenance as the maintenance service chart in this manual is not covered

by warranty.

CHECK ITEMS CHECK AND SERVICE INTERVALS PAGE

Engine oil 163 Page

Change : At end of first 1,000km,

long distance : every 30,000km

short distance : every 20,000km

D1146Ti

DE08TiS

DE12/T/Ti/TiS

Fuel filter

D1146

D1146Ti

DE12

DE12T

DE12Ti

Primary filter : clean at every 5,000km,

change at every 15,000km there after.

secondary filter : change at every 5,000km.

Engine oil filter Change with engine oil 164Page

DE08TiS

DE12TiS

Change : At end of first 1,000km,

High-speed, long distance : every 15,000km

In city, short distance : every 10,000km

This manual has been prepared to acquaint you with the operation and maintenance of your DAEWOO

BUSES and the provide important safety information. We urge you to read it carefully and follow the

recommendations to help assure the most enjoyable, safe and troublefree operation of your vehicle.

When it comes to service, remember that your DAEWOO dealer knows your vehicle best and is

interested in your complete satisfaction.

We would like to take this opportunity to thank you for choosing a DAEWOO product and assure

you of our continuing interest in your motoring pleasure and satisfaction.

This manual should be considered as a permanent part of your vehicle, and must remain with the

vehicle at the time of resale.

All information, illustrations and specifications contained in this manual are based on the latest product

information available at time of publication.

The right is reserved to make changes at any time without notice.

FOREWORD

1. IMPORTANT INFORMATIONŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 2

2. OPERATION AND CARE OF NEW VEHICLEŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 4

3. GETTING ON AND OFF, DRIVER’S SEAT AND BELT ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 6

4. INSTRUMENT, SWITCHES AND CONTROLSŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 14

5. DRIVINGŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 135

6. INSPECTION AND MAINTENANCEŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 162

7. LUBRICATION ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 213

8. SCHEDULED MAINTENANCE SERVICEŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 221

9. TROUBLESHOOTINGŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 225

10. MAIN DATA AND SPECIFICATIONŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 234

11. BODY DIMENSION ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 253

TABLE OF CONTENTS

IMPORTANT INFORMATION

LOCATION OF ENGINE NUMBER AND CHASSIS NUMBER

It is advisable to keep note of the engine number and chassis number as they are required when contacting your deal-

er for repair services and parts order.

V.I.N plate

V.I.N(Vehicle identification Number)

plate is attached to the inner panel

above the front door.

Type A : Applicable for vehicles in

all countries except GCC

members.

V.I.N plate

V.I.N(Vehicle identification Number)

plate is attached to the inner panel

above the front door.

Type B : Applicable for vehicles in

GCC members.

Chassis number

The chassis number is stamped on

the upper face of the chassis frame

within the engine compartment.

Engine number Key

There are three types of key for the

bus ;

• Engine starting

• Mechanical locking for entrance

door (OPTION)

• Doors

– Entrance door operating

– Luggage doors (OPTION)

– Rear engine door (OPTION)

– Side engine doors (OPTION)

– Battery inspection door (OPTION)

–

Fuel tank inspection door (OPTION)

– Fuel inlet flap door (OPTION)

The keys are not interchangeable, but

door lock keys are interchangeable.

The code number of each key is

stamped on the key.

Record the key number and keep it

in a safe place.

In the event that the original key is

lost, duplicating can be done using

the key code information.

Engine No.

1378

OPERATION AND CARE OF NEW VEHICLE

It is important to observe the follow-

ing precautions as operation and care

of the vehicle, particularly during the

break–in period have a strong influ-

ence over the performance and ser-

vice life of the vehicle.

1. Start and let the engine idle until

it becomes thoroughly warmed up

and coolant temperature increases

beyond 50°C (or 125°F) before

starting off.

2. Avoid racing the engine, abrupt

starts and hard stops.

3. Avoid over loading the vehicle dur-

ing and after the break–in period.

Over loading

Over loading not only shortens the

service life of your vehicle but also

create serious potential safety haz-

ards.

The weight of payload must be limit-

ed within the GVW rating and distrib-

uted over the front and rear axles so

as not to exceed the axle capacities.

Refer to “MAIN DATA AND SPECIFI-

CATION” for GVW and Axle capaci-

ty.

Maintenance

In order to maintain safe and depend-

able vehicle operation, inspection and

adjustment should be performed as

outlined in “INSPECTION AND MAIN-

TENANCE”.

Your DAEWOO dealer is willing to

perform regular maintenance opera-

tion on your vehicle.

Engine oil change

Change engine oil filter catridge to new one at the

same time with engine oil.

Maximum engine speed

During the initial milage(Break–in period : 2,000km),

confine engine speed to 70% of the maximum and

scan the tachometer as you drive to prevent engine

over–running.

After the break–in period, increase the engine speed

gradually to complete running–in of the vital parts.

Engine Model Change Interval

D1146 At end of first 1,000km

D1146Ti High–speed, long distance :

DE12Ti every 15,000km

DE12TiIn city, short distance :

DE12Ti every 10,000km

DE08TiS At end of first 1,000Km

Long distance : every 30,000km

DE12TiS short distance : every 20,000km

GETTING ON AND OFF, DRIVER’S SEAT AND BELT

DOOR OPENING AND CLOSING

(Applicable for vehicles in all

entrance door with mechanical key)

When opening the front door to get

in, first unlock the mechanical key on

the entrance door and operate the

entrance key on the right side of the

front middle panel.

When closing the front door to get

off, open the front door by operating

the door control switch and get off.

In the outside of bus, close the door

with the key and look the mechanical

key on the entrance door not to be

opened in case of air leaking.

(Applicable for vehicles in all

entrance door except mechanical key)

When opening the front door to get

in, operate the entrance key on the

right side of the froot middle panel.

When closing the front door to get

off, open the front door by operating

the door control switch and get off.

In the outside of bus, close the door

with the key.

Before operating entrance key, unlock

mechanical key on door frame.

NOTICE

When opening front entrance door for a long time, setting emergency valve

at manual position and put control switch in close position. When returning

to automatic condition, putting control switch and door in same condition

and set emergency valve at automatic position.

CAUTION

(Type A : Toggle switch) (Type B : One touch switch)

MANUAL OPENING AND

CLOSING

Type A : Select type

As setting the “Auto–Manual” change

lever installed right, lower inner side

of front panel(beside of driver’s right

leg), the door can be opened and

closed by hands.

Type B :

Push/Pull or rotary type (OPTION)

As setting the "Auto-Manual" change

knobs are installed two types. One of

the types installed inner upper panel

the entrance door operated by air.

Other installed outer mid panel on left

side of door operated by electric push

button. the door can be opened and

closed by hands.

(Push/Pull type) (Rotary type)

Adjustment of Fixed type (S-104H) (BM090, BS090)

1. Back angle adjustment

To adjust the seat back, turn No. 1 handle, and lean

backwards and foreward until desired angle is

achieved.

2. Slide adjustment

To move the seat forward and backward.

Pull No. 2 lever, forward and slide the seat.

3. Height (Tilting) adjustment

Desired the seal height can be achieved by puling

No. 3 lever upward and downward.

DRIVER’S SEAT AND BELT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Daewoo Andere Handbücher

Daewoo

Daewoo DVT-21F1LA Bedienungsanleitung

Beliebte Andere Handbücher anderer Marken

GO Industries

GO Industries 38017 Bedienungsanleitung

Cissell

Cissell 30LBCMAN2 Bedienungsanleitung

RIDGID

RIDGID K-60SP Bedienungsanleitung

Gage Bilt

Gage Bilt GB751SH-5 Bedienungsanleitung

OVE

OVE SIERRA 60 Bedienungsanleitung

ReelCraft

ReelCraft 7800 OLB21 Bedienungsanleitung

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Bedienungsanleitung

ROBLIN

ROBLIN DROP Benutzerhandbuch

EMG

EMG EMG-ACB BARREL Service-Handbuch

MiniSolar

MiniSolar MT-150 Bedienungsanleitung

Parkside

Parkside PSZ 250 B2 Bedienungsanleitung

ABB

ABB REM 610 Produkthandbuch

Parkside

Parkside 55992 Betriebsanleitung

Skyjacker

Skyjacker F250 Bedienungsanleitung

IBM

IBM IBM SYSTEM Z Installationsanleitung

Grech Motors

Grech Motors G28 Bedienungsanleitung

NOVAK

NOVAK BATTERY CARE SHEET Leitfaden

Telemotive

Telemotive blue PiraT Mini Benutzerhandbuch