Dahua Technology Lite IPCHFW2231T-ZAS-S2 Bedienungsanleitung

IR Bullet Network Camera

Quick Start Guide

V1.0.0

ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD

Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Dahua Lite IPC-

HFW2231T-ZAS-S2 o cerca il tuo prodotto tra le migliori offerte di Videosorveglianza

Foreword I

Foreword

General

This Quick Start Guide (hereinafter referred to be "the Guide") introduces the functions,

installation and operations of the camera.

Safety Instructions

The following categorized signal words with defined meaning might appear in the guide.

Signal Words

Meaning

Indicates a medium or low potential hazard which, if not avoided,

could result in slight or moderate injury.

Indicates a potential risk which, if not avoided, may result in

property damage, data loss, lower performance, or unpredictable

result.

Provides additional information as the emphasis and supplement

to the text.

Revision History

No.

Version

Revision Content

Release Date

V1.0.0

First release.

2018.03

Protect Privacy Notice

As the device user or data controller, you might collect personal data of others' such as face,

fingerprints, car plate number, Email address, phone number, GPS and so on. You need to be

in compliance with the local privacy protection laws and regulations to protect the legitimate

rights and interests of other people by implementing measures include but not limited to:

providing clear and visible identification to inform data subject the existence of surveillance

area and providing related contact.

About this Guide

The Guide is for reference only. If there is inconsistency between the Guide and the actual

product, the actual product shall prevail.

We are not liable for any loss caused by the operations that do not comply with the Guide.

The Guide would be updated according to the latest laws and regulations of related

regions. For detailed information, see the paper Quick Start Guide, CD-ROM, QR code or

our official website. If there is inconsistency between paper User's Guide and the electronic

version, the electronic version shall prevail.

Foreword II

All the designs and software are subject to change without prior written notice. The product

updates might cause some differences between the actual product and the Guide. Please

contact the customer service for the latest program and supplementary documentation.

There still might be deviation in technical data, functions and operations description, or

errors in print. If there is any doubt or dispute, please refer to our final explanation.

Upgrade the reader software or try other mainstream reader software if the Guide (in PDF

format) cannot be opened.

All trademarks, registered trademarks and the company names in the Guide are the

properties of their respective owners.

Please visit our website, contact the supplier or customer service if there is any problem

occurred when using the device.

If there is any uncertainty or controversy, please refer to our final explanation.

Important Safeguards and Warnings III

Important Safeguards and Warnings

Electrical safety

All installation and operation should conform to your local electrical safety codes.

The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and

supply power with rated voltage which conforms to Limited power Source requirement

according to IEC60950-1. Please note that the power supply requirement is subject to the

device label.

Make sure the power supply is correct before operating the device.

A readily accessible disconnect device shall be incorporated in the building installation

wiring.

Prevent the power cable from being trampled or pressed, especially the plug, power socket

and the junction extruded from the device.

Environment

Do not aim the device at strong light to focus, such as lamp light and sun light; otherwise it

might cause over brightness or light marks, which are not the device malfunction, and

affect the longevity of Complementary Metal-Oxide Semiconductor (CMOS).

Do not place the device in a damp or dusty environment, extremely hot or cold

temperatures, or the locations with strong electromagnetic radiation or unstable lighting.

Keep the device away from any liquid to avoid damage to the internal components.

Keep the indoor device away from rain or damp to avoid fire or lightning.

Keep sound ventilation to avoid heat accumulation.

Transport, use and store the device within the range of allowed humidity and temperature.

Heavy stress, violent vibration or water splash are not allowed during transportation,

storage and installation.

Pack the device with standard factory packaging or the equivalent material when

transporting the device.

Install the device in the location where only the professional staff with relevant knowledge

of safety guards and warnings can access. The accidental injury might happen to the

non-professionals who enter the installation area when the device is operating normally.

Operation and Daily Maintenance

Do not touch the heat dissipation component of the device to avoid scald.

Carefully follow the instructions in the Guide when performing any disassembly operation

about the device; otherwise, it might cause water leakage or poor image quality due to

unprofessional disassemble. Please contact after-sale service for desiccant replacement if

there is condensed fog found on the lens after unpacking or when the desiccant turns

green. (Not all models are included with the desiccant).

It is recommended to use the device together with lightning arrester to improve lightning

Important Safeguards and Warnings IV

protection effect.

It is recommended connect the grounding hole to the ground to enhance the reliability of

the device.

Do not touch the image sensor directly (CMOS). Dust and dirt could be removed with air

blower, or you can wipe the lens gently with soft cloth that moistened with alcohol.

Device body can be cleaned with soft dry cloth, which can also be used to remove

stubborn stains when moistened with mild detergent. To avoid possible damage on device

body coating which could cause performance decrease, do not use volatile solvent such as

alcohol, benzene, diluent and so on to clean the device body, nor can strong, abrasive

detergent be used.

Dome cover is an optical component, do not touch or wipe the cover with your hands

directly during installation or operation. For removing dust, grease or fingerprints, wipe

gently with moisten oil-free cotton with diethyl or moisten soft cloth. You can also air blower

to remove dust.

Please strengthen the protection of network, device data and personal information by

adopting measures which include but not limited to using strong password, modifying

password regularly, upgrading firmware to the latest version, and isolating computer

network. For some device with old firmware versions, the ONVIF password will not be

modified automatically along with the modification of the system password, and you need

to upgrade the firmware or manually update the ONVIF password.

Use standard components or accessories provided by manufacturer and make sure the

device is installed and maintained by professional engineers.

The surface of the image sensor should not be exposed to laser beam radiation in an

environment where a laser beam device is used.

Do not provide two or more power supply sources for the device unless otherwise specified.

A failure to follow this instruction might cause damage to the device.

Regulatory Information V

Regulatory Information

FCC Information

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

FCC conditions:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause

undesired operation.

FCC compliance:

This equipment has been tested and found to comply with the limits for a digital device,

pursuant to part 15 of the FCC Rules. This equipment generate, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the guide, may cause

harmful interference to radio communication.

For class A device, these limits are designed to provide reasonable protection against

harmful interference in a commercial environment. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

For class B device, these limits are designed to provide reasonable protection against

harmful interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Table of Contents VI

Table of Contents

Foreword.................................................................................................................................................... I

Important Safeguards and Warnings...................................................................................................... I

Regulatory Information...........................................................................................................................IV

1 Introduction............................................................................................................................................ 1

1.1 Cable............................................................................................................................................. 1

1.2 Connecting Alarm Input/output ..................................................................................................... 2

2 Network Configuration.......................................................................................................................... 4

2.1 Initializing Device .......................................................................................................................... 4

2.2 Modifying Device IP Address........................................................................................................ 5

2.3 Logging in Web Interface.............................................................................................................. 6

3 Installation.............................................................................................................................................. 8

3.1 Packing List................................................................................................................................... 8

3.2 Dimension ..................................................................................................................................... 8

3.3 Installing Device............................................................................................................................ 9

3.3.1 Installation method.............................................................................................................. 9

3.3.2 Installing SD Card (Optional).............................................................................................. 9

3.3.3 Attaching Device............................................................................................................... 10

3.3.4 Installing Waterproof Connector....................................................................................... 12

3.3.5 Adjusting Angle ................................................................................................................. 12

3.3.6 Adjusting Focal Length ..................................................................................................... 13

Introduction 1

1 Introduction

1.1 Cable

Cable type might vary with different devices, and the actual product shall prevail.

Please waterproof all the cable joints with insulating tape and waterproof tape to avoid

short circuit and water damage. For the detailed operation, see the FAQ manual.

Cable listFigure 1-1

For more information about cable ports, see Table 1-1.

Table 1-1 Cable Information

Port name

Function description

DC 12V power

input

Inputs DC 12V.

Alarm I/O

Includes alarm signal input and output ports, the number

of I/O ports might vary on different devices. For detailed

information, see Table 1-2.

Ethernet port

Connects to network with network cable.



Provides power to the device with PoE.



PoE is available on select model.

Audio input

Connects to sound-pick-up device to receive audio signal.

Audio output

Connects to speaker to output audio signal.

For more information about I/O port, see Table 1-2.

Table 1-2 Alarm Information

Port

Port Name

Function

Alarm I/O

ALARM_OUT

Outputs alarm signal to alarm device.

ALARM_IN

Receives the switch signal of external alarm source.

Introduction 2

Port

Port Name

Function

ALARM_GND

Ground connection.

1.2 Connecting Alarm Input/output

Alarm input/output is available on select models.

Connect alarm input device to the alarm input end of the I/O port, see Figure 1-2.Step 1 Device collects different states of alarm input port when the input signal is idling and

being grounded.

Device collects logic "1" when input signal is connecting to +3V to +5V or idling.

Device collects logic "0" when input signal being grounded.

Alarm inputFigure 1-2

Connect alarm output device to the alarm output end of the I/O port. The alarm outputStep 2 is open-drain output, which works in the following modes.

Mode A: Level application. Alarm outputs high and low level, and the alarm outlet

is OD, which requires external pull-up resistance (10K Ohm typical) to work. The

maximum external pull-up level is 12V, maximum port current is 300mA and the

default output signal is high level (external pull-up voltage). The default output

signal switches to low level when there is alarm output (As long as the operating

current below 300mA, the output low level voltage is lower than 0.8V).

Mode B: Switch application. Alarm output is used to drive external circuit, the

maximum voltage is 12V and the maximum current is 300mA. If the voltage is

higher than 12V, please use an additional electric relay.

Introduction 3

Mode AFigure 1-3

Mode BFigure 1-4

The alarm input in the web interface is corresponding to the alarm input end of the

I/O port. There will be high level and low level alarm signal generated by the alarm

input device when alarm occurs, set the input mode to "NO" (default) if the alarm

input signal is logic "0" and to "NC" if the alarm input signal is logic "1".

The alarm output in the web interface is corresponding to the alarm output end of

the device, which is also alarm output end of the I/O port.

Inhaltsverzeichnis

Andere Dahua Technology Sicherheitskamera Handbücher

Dahua Technology

Dahua Technology IPC-HDW5231R-Z Bedienungsanleitung

Dahua Technology

Dahua Technology WizMind IPC-PDBW82041-B360 Bedienungsanleitung

Dahua Technology

Dahua Technology 8A840WANF Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HDW1239DT-PV-STW Bedienungsanleitung

Dahua Technology

Dahua Technology N42BD32 Bedienungsanleitung

Dahua Technology

Dahua Technology D-IPC-HDBW3441F-AS-M-0360B Bedienungsanleitung

Dahua Technology

Dahua Technology DH-PSDW8842ML-A180-D237 Bedienungsanleitung

Dahua Technology

Dahua Technology 22204TNI Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HDBW1531E-S-0280B Bedienungsanleitung

Dahua Technology

Dahua Technology Pro IPC-HDW5241TM-AS Bedienungsanleitung

Dahua Technology

Dahua Technology 52C230UNI Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HFW3841E-AS-0280B-S2 Bedienungsanleitung

Dahua Technology

Dahua Technology A21BM0V Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HFW1239DQ-PV-STW Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HDB3202-DI Series Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HUM4231S-L4-0280B-S3 Bedienungsanleitung

Dahua Technology

Dahua Technology N82AL32 Bedienungsanleitung

Dahua Technology

Dahua Technology N28BL7Z Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HFW5431E-Z Bedienungsanleitung

Dahua Technology

Dahua Technology DH-IPC-PFW83242-A180-S2 Bedienungsanleitung

Dahua Technology

Dahua Technology DH-IPC-HFW4X-W Bedienungsanleitung

Dahua Technology

Dahua Technology 6CE230UNI Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HFW81230E-Z Bedienungsanleitung

Dahua Technology

Dahua Technology IPC-HDW3549H-ZAS-PV-27135 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung