Danby Diplomat DAC7037M Bedienungsanleitung

USE AND CARE

MANUAL

MANUEL

D'UTILISATION

Model • Modèle

DAC7037M

CAUTION:

Read and Follow All Safety Rules

and Operating Instructions Before

First Use of This Product.

PRÉCAUTION:

Veuillez lire attentivement

les consignes de sécurité et les

instructions d'utilisation avant

l'utilisation initiale de

ce produit.

Room Air Conditioner

Table of contents . . . . . . . . . . . . . . . . . . . . . . . 1

Climatiseur de pièce

Table of contents . . . . . . . . . . . . . . . . . . . . . . . 11

Danby Products Limited, Guelph, Ontario Canada N1H 6Z9

Danby Products Inc., Findlay, Ohio USA 45839-0669

10.01.

DAC7037M 2006-11-14 Y.P.Chen

Page

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Energy-Saving Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation Notes & Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Trouble Shooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Table of Contents

Parts Identification Model DAC7037M

Interior

Air Inlet

Air Filter

Cabinet

Exterior Air

Inlet

Interior

Air Outlet

Control Panel

Specifications

Voltage 115V/60Hz

Cooling Capacity (Btu/h) 7,000

Input Wattage 820w

Energy Efficiency Rating (EER) 9.8

Fan/Cooling Speeds 3/3

Cooling Area Coverage 200Sq.ft.(18.6m )

Noise Level (dB) 61

Unit Dimensions Width 18-8/16"(470mm)

Depth 16-5/16"(415mm)

Height 12-10/16"(320mm)

Window Kit Dimensions Maximum Width 34-8/16"(876mm)

Minimum Width 21-8/16"(546mm)

Minimum Height 13-6/16"(340mm)

Unit Weight 52.8 lbs(24kg)

NOTE:

Specifications are subject to change without notice for further improvement.

Introduction

Thank you for choosing a Diplomat Room Air Conditioner to cool your home. This Use and Care Manual

provides information necessary for the proper care and maintenance of your new Room Air Conditioner. If

properly maintained, your air conditioner will give you many years of trouble free operation. To avoid

installation difficulties, read these instructions completely before installing/operating your unit.

NOTE: This unit is NOT designed for through-the-wall installation.

For easy reference, you may want to attach a copy of your sales receipt to this page. Note following

information provided (on the manufacturer’s nameplate located on the right side of the unit). This information

will be needed when you contact a Customer Service Representative.

Model Number: DAC7037M

Serial Number: ___________________________________________________

Date of Purchase: _________________________________________________

Dealer’s Name and Address: ________________________________________

________________________________________

Refer to the trouble shooting section of this Use and Care Manual if the unit is not operating correctly.

If these suggestions do not solve the problem, contact an authorized service representative or

call Danby TOLL FREE:

1-800-26-Danby

Keep these instructions for future reference.

This symbol denotes a caution or warning

CAUTION

Do not leave a room air conditioner unattended in

a space where people or animals who cannot

react to a failed unit are located. A failed unit can

cause extreme overheating and fire in an

enclosed, unattended space.

Electrical Specifications

1. All wiring must comply with local and national

electrical codes and must be installed by a

qualified electrician. If you have any questions

regarding the following instructions, contact a

qualified electrician.

2. Check available power supply and resolve any

wiring problems BEFORE installing and

operating this unit.

3. This 115V air conditioner uses 12.0 or less

nameplate amps and may be used in any

properly wired, general purpose household

receptacle. See Table 1 for specifications for

individual branch circuit.

4. For your safety and protection, this unit is

grounded through the power cord plug when

plugged into into a matching wall outlet. If

you are not sure whether your wall outlet is

properly grounded, please consult a

qualified electrician.

5. The wall outlet (3-pin) must match the plug (3-

pin) on the service cord supplied with the unit.

DO NOT use plug adapters. See Table 2 for

receptacle and fuse information. If it is necessary

to use an extension cord to connect your air

conditioner, use an approved "air conditioner"

extension cord only. (available at most local

hardware stores)

6. The rating plate on the unit contains electrical

and other technical data. The rating plate

is located on the right side of the unit, above the

power cord.

Table 1:

Suggested Individual Branch Circuit

Nameplate Amps AWG Wire Size*

5.0 to 12 14

AWG- American Wire Gage

* Based on copper wire at 60 °C temperature rating.

Table 2:

Receptacle and Fuse Types

Rated Volts 125

Amp 15

Wall Outlet

Fuse Size 15

Time Delay Fuse Plug Type

(or circuit breaker)

The power cord supplied with this air conditioner

contains a current leakage detection device de-

signed to reduce the risk of fire.Please refer to the

section “ Power Supply Cord”for details.In the

event the power supply cord is damaged,it cannot

be repaied it must be replaced with a new cord

from the Product Manufacturer.

Under no circumstances should this device be

used to turn the air conditioner on or off.

The ‘RESET’ button must always be pushed in

(engaged) for correct operation.

The power supply cord must be replaced if it fails

to reset when the ‘TEST’button is pushed in.

If the power supply cord is damaged, it cannot be

repaired.It must be replaced with a new cord

obtained from the Product Manufacturer.

The power cord supplied with this air conditioner

contains a device that senses damage to the power

cord.To test if your power supply cord is working

properly . you must do the following;

1.Connect the power supply cord to an electrical

outlet.

2.The power supply cord is inclusive of two buttons

located on the head of the plug. One button is

marked ‘TEST’, the other button is marked’RESET’.

Press the ’TEST’ button,you will hear a click as the

‘RESET’ button pops out.

3.Press the ‘RESET’ button, you will hear a click as

the button engages.

4.The power supply cord is now energized and

supplying electricity to the air conditioner.(On some

products this is also indicated by a light on the plug

head).

Installation Notes

Tools Needed for Installation

Screw Drivers: Both Phillips and flat head

Power Drill: 1/8 inch(3mm) diameter drill bit

Pencil

Measuring Tape

Scissors

Carpenters Level

Your Room Air Conditioner is designed for easy

installation in a single or double-hung window. This

unit is NOT designed for vertical (slider type)

windows and/or through-the-wall applications.

NOTE: Save the shipping carton and packing

materials for future storage or transport of the unit.

Remove from carton, the plastic bag containing the

installation hardware kit necessary for the installation

of your air conditioner. Please check the contents of

hardware kit against the corresponding model check

list, prior to installation of the unit.

See Fig. 1

CAUTION

To avoid installation/operation difficulties,

read these instructions thoroughly.

Electric Shock Hazard

To avoid the possibility of personal

injury, disconnect power to the unit

before installing or servicing.

Energy-Saving Tips

Your Room Air Conditioner is designed to be

highly efficient in energy savings. Follow these

recommendations for greater efficiency.

1. Select thermostat setting that suits your

comfort needs and leave thermostat at that

chosen setting.

2. The filter is very efficient in removing airborne

particles. Keep air filter clean. Normally, filter

should be cleaned every 2 weeks. More

frequent cleaning may be necessary depending

on indoor air quality.

3. Use drapes, curtains, or shades to keep

direct sunlight from heating room, but DO NOT

obstruct the air conditioner. Allow air to circulate

around the unit without obstruction.

4. Start your air conditioner before outdoor air

becomes hot and uncomfortable. This avoids an

initial period of discomfort while unit is cooling

off the room.

5. When outdoor temperatures are cool enough,

use HIGH or LOW FAN only. This circulates

indoor air, providing some cooling comfort, and

utilizes less electricity than when operating on a

cooling setting.

raw

4/3 )7( s

swer

cS )

5.9(

"8/

*)4(

)1(

coL

tefaS

)1( HL niat

C ediS

evisehd

( lae

mao

dep

S”L“* te

kca

itnuo

(

R niatruC ed

)

(

tekcarb h

Your unit is designed to evaporate condensation

under normal conditions. However, under

extreme humidity conditions, excess condensation

may cause basepan to overflow to the outside.

The Unit should be installed where condensation

run-off cannot drip on pedestrians or neighboring

properties.

Select the Best Location

A. This room air conditioner is designed to fit easily

into a single or double hung window. However,

since window designs vary, it may be necessary

to make some modifications for safe, proper

installation.

B. Make sure window and frame are structurally

sound and free from dry and rotted wood.

C. For maximum efficiency, install the air conditioner

on a side of a house or building which favors

more shade than sunlight. If the unit is in direct

sunlight, it is advisable to provide an awning over

the unit.

D. Provide sufficient clearance around the cabinet

to allow for ample air circulation through the unit.

See Fig. 2. The rear of the unit should be

outdoors and not in a garage nor inside a

building. Keep unit as far away as possible from

obstacles/obstructions and at least 30" above the

floor or ground. Curtains and other objects

within a room should be prevented from blocking

the air flow.

E. Be certain the proper electrical outlet is within

reach of the installation. Use only a single

outlet circuit rated at 15 amps. All wiring should

be in accordance with local and national

electrical codes.

F. DO NOT USE "REGULAR" EXTENSION CORDS

WITH THIS UNIT. If it is necessary to use an

extension cord to connect your air conditioner,

use an approved "air conditioner" extension cord

only. (available at most local hardware stores)

G. DO NOT install unit where leakage of

combustible gas is suspected. Your air

conditioner may fail to operate in air containing

oils (including machine oils), sulfide gas, near hot

springs, etc...

Side

obstruction

20"(508mm)

Min.

Fig. 2 Ground

Fence,

wall, or

other

obstacle.

Awning

12" Min.(305mm)

30"(762mm)

Min.

20"(508mm)

Min.

CAUTION

Because the compressor is located on the

controls side of the unit (left side), this side will

be heavier and more awkward to manipulate.

Inadequate support on control side of the unit

can result in personal injury and damage to your

unit and property. Therefore, it is recommended

to have someone assist you during the

installation of this unit.

Installation

1. Assembly of the Upper Channel, to

Cabinet.

•"L" Shaped Top Channel: Install the "L"

shaped channel to the top of the cabinet as

shown in Fig.3 using four(4)3/8"(10mm)screws.

2. Assembly of the Side Curtains to

Cabinet.

• Extend the shutter from the shutter frame and

slide it into the shutter tabs on the side channel

of the air conditioner as shown in Fig. 4.

• Slide the shutters into the top (“L” Shaped) and

bottom (“U” Shaped channels. The shutters are

identified (on frame) as left & right.

3. Completing the Installation

•Cut the foam (non adhesive) sealing strip to

fit the area of the window sill that the air

conditioner will rest on.

3a. Completing the Installation (cont’d)

• Carefully place the air conditioner into the

window with the “L” shaped mounting bracket

(on top) positioned in front of the upper window

sash. The bottom of the cabinet should be

positioned on the “recessed” portion of the

window frame. Pull the window down until it

rests just behind the front flange of the (top) “L”

shaped mounting bracket. See Fig. 5.

• Expand the shutter frames (fully) on each side

and secure the top of the frames to the window

sash using one 3/4"(19mm)screw on each side

and one

in the “L” shaped mounting bracket.

See Fig. 5

• Secure the shutter clamp on each side of the

(lower) shutter and secure to window sill using

one 3/4"(19mm)screw on each side. Fig.5

• Place the second foam sealing strip to fit the

opening between the inside and outside windows

then attach the safety lock to the outside window

frame using one 3/4”(19mm) scre w. See Fig. 6.

PLEASE NOTE: Window applications come in a

variety of different styles. Therefore, it may be

necessary to modify or improvise your particular

installation.

3/8"(10mm) Screw

“L” Shaped

Mounting Bracket

Fig. 3

“U” Shaped Channel

(Factory Installed)

Fig. 5

“L” Shaped

Mounting

Bracket

Window Sash

Fig. 6

Foam Seal

Shutter clamps

Safety Lock

3/4"(19mm) Screws

3/4"(19mm) Screw

Shutter Frame

Shutter

Fig. 4

Shutter Tabs

" "

Operating Instructions

SELECTOR SWITCH

The selector switch controls fan speed and/or

cooling speed.

To set desired cooling

temperature, simply rotate the SELECTOR

knob to the appropriate setting.

FAN SPEEDS

LOW FAN will circulate air at minimum

speed without cooling.

MED

FAN will circulate air at medium

speed without cooling.

COOLING MODES

W COOL provides cooling with

minimum air circulation. Recommended for

night-time use.

HIGHCOOL provides cooling with

maximum air circulation. Recommended for

quick cooling or for extremely hot days. Once

room is cooled, reduce setting to LOW COOL.

OFF shuts-down the unit completely.

NOTE: Always allow 3 minutes before

switching from one mode to another.

THERMOSTAT

The thermostat automatically controls the

(compressor) cooling cycle and maintains the

selected room temperature. To set the

thermostat, rotate the thermostat knob to the

desired cooling setting (1 warmest ~ 7 coldest).

The fan motor will continue to operate after the

compressor (cooling) has cycled off. This is

normal.

•

HIGHFAN will circulate air at maximum

speed without cooling.

•

Selector

Switch

Thermostat

CAUTION

When using FAN control, turn selector switch

slowly allowing unit to adjust.

When using THERMOSTA

T, be sure to allow three

minutes before changing temperature.

Adjusting

too quickly may cause compresspr to overload.

ARRÊT

OFF

TEMP.

MED COOL provides cooling with

medium air circulation. Recommended for

night-time use.

•

Care and Maintenance

When cleaning the air conditioner, be sure to

turn the SELECTOR knob to the “OFF” position

and disconnect the power cord from the

electrical outlet.

1. DO NOT use gasoline, benzine, thinner or other

chemicals on the air conditioner as these

substances may cause damage to the paint finish

and deformation of plastic parts.

2. Never attempt to pour water directly on unit as

this will cause deterioration of the electrical

insulation.

Air Filter Information

If the air filter becomes clogged with dust, air flow

is obstructed and reduces efficiency. The air filter

should be cleaned every 2 weeks.

Air Filter Removal:

To reinstall the air filter, reverse the above

procedures. The air filter may be vacuumed or

washed by-hand in warm water. Dry thoroughly

before installing.

Cleaning Air Filter

1. Use a vacuum cleaner with soft brush

attachment.

2. Wash the filter in lukewarm water below 40°C

(104°F): To get better results, wash with soapy

water or a neutral cleaning agent.

3. Rinse the filter with clean water and

dry thoroughly before re-installing.

End-of-Season Care

1. Operate the fan alone for half a day to dry out the

inside of the unit.

2. Turn off power and remove plug from wall socket.

3. Clean filter.

4. Store (covered) air conditioner in a dry location.

CAUTION

When installing and/or removing the air

conditionner from the window, ensure that

caution is taken to prevent the from failing

backward. It is recommended that installtion

or removal of the airconditioner is done with

assitance to prevent injury to persons or

damage to the unit or property.

IMPORTANT

DO NOT forget to install the air filter. If the air

conditioner is left to operate without the air filter,

dust is not removed from the room air and may

result in machine failure.

When the air inlet grill and cabinet are dirty, wipe

with lukewarm water (below 40°C). Use of a mild

detergent is recommended.

The air filter is located behind the air intake front

grill. To remove the air filter, grasp the sides of the

front grill and pull forward to open and access the

filter.

Trouble shooting Guide

Frequently, a problem is minor and a service call may not be necessary, use this trouble shooting guide for a

possible solution. If the unit continues to operate improperly, call Danby’s Toll Free Number 1-800-263-2629 for

assistance, or call one of our service depots listed in the enclosed “Authorized Service Depot” listing provided

with this unit.

Difficulty Possible Cause Suggested Solution

Air conditioner will No power to unit. Check connection of power cord to

not operate. power source.

Check fuse or circuit breaker.

Set SELECTOR SWITCH to position other

than “OFF”.

Inefficient or no cooling. Dirty air filter. Clean or replace air filter.

Unit size inappropriate Check with dealer to determine proper unit

for application. capacity for application.

Blocked air flow. Remove obstruction from grill or

outdoor louvers.

Power interruption, settings Turn the unit off and wait 5 minutes before

changed too quickly, or attempting to re-start.

compressor overload tripped.

Noisy unit. Loose parts. Tighten loose parts.

Inadequate support. Provide additional support to unit.

Odors. Formation of mold, mildew, or Clean unit thoroughly.

algae on wet surfaces. Place algaecide tablet in base pan.

Water dripping outside. Hot and humid weather. Condensation run-off is normal under these

conditions.

Water dripping inside. Unit is not properly angled to Unit must be installed on an angle for proper

allow water to drain outside. condensation run-off. Check the unit and

make any adjustments.

Ice or frost build-up. Low outside temperature. When outdoor temperature is approximately

65°F or below, frost may form when unit is in

cooling mode. Switch unit to FAN (only)

operation until frost melts.

Unit air filter is dirty. Remove and clean filter.

NOTES: 1. If circuit breaker is tripped repeatedly, or fuse is blown more than once, contact a

qualified technician.

2. When unit is installed using proper installation steps, unit is properly tipped towards the

outdoors to allow for condensation run-off.

Inhaltsverzeichnis

Andere Danby Klimaanlage Handbücher

Danby

Danby DAC6020 Bedienungsanleitung

Danby

Danby Premiere DPAC 9009 Montageanleitung

Danby

Danby DAC060BBCWDB Montageanleitung

Danby

Danby DAS120EAQHWDB Bedienungsanleitung

Danby

Danby DAC080BFCWDB Bedienungsanleitung

Danby

Danby DPA120E3WDB-6 Bedienungsanleitung

Danby

Danby Diplomat DAC5040 Bedienungsanleitung

Danby

Danby Premiere DPAC9009 Montageanleitung

Danby

Danby Premiere DAC8075EE Bedienungsanleitung

Danby

Danby DAC060BFCWDB Bedienungsanleitung

Danby

Danby DAC050MB1WDB Bedienungsanleitung

Danby

Danby DPA120CB1WDB Montageanleitung

Danby

Danby Premiere DPAC9009 Bedienungsanleitung

Danby

Danby DPA053B4WDB Bedienungsanleitung

Danby

Danby DAC12344DE Bedienungsanleitung

Danby

Danby DPA120B1WB Bedienungsanleitung

Danby

Danby DPA060BACBDB Montageanleitung

Danby

Danby DAC145EB6WDB-RF Bedienungsanleitung

Danby

Danby DAC18002 Bedienungsanleitung

Danby

Danby DPA120B3WDB Montageanleitung

Danby

Danby DAC8007EE Montageanleitung

Danby

Danby DPA058B6WDB-RF Bedienungsanleitung

Danby

Danby DAC 5209M Montageanleitung

Danby

Danby DPA100B6WDB Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung