Danfoss VLT HVAC Bedienungsanleitung

Contents

1. Safety

Safety Instructions 3

General Warning 4

Before Commencing Repair Work 4

Special conditions 4

Avoid unintended Start 6

Safe Stop of the Frequency Converter 7

IT Mains 8

2. Introduction

Type Code String 10

3. Mechanical installation

Before starting 13

How to install 14

4. Electrical installation

How to connect 21

Mains wiring overview 24

How to connect motor - foreword 28

Motor wiring overview 30

Motor connection for C1 and C2 33

How to Test Motor and Direction of Rotation. 35

5. How to operate the frequency converter

Three ways of operating 41

How to operate graphical LCP (GLCP) 41

How to operate numeric LCP (NLCP) 47

Tips and tricks 52

6. How to programme the frequency converter

How to programme 55

Initialisation to Default Settings 86

Parameter list 88

0-** Operation and Display 89

1-** Load/Motor 91

2-** Brakes 92

3-** Reference/Ramps 93

4-** Limits/Warnings 94

5-** Digital In/Out 95

6-** Analog In/Out 97

VLT

HVAC Drive Operating Instructions Contents

MG.11.A4.02 - 09.10.06. VLT®is a registered Danfoss trademark

8-** Comm. and Options 99

9-** Profibus 100

10-**CAN Fieldbus 101

11-** LonWorks 102

13-** Smart Logic 103

14-** Special Functions 104

15-** FC Information 105

16-** Data Readouts 107

18-** Data Readouts 2 109

20-** FC Closed Loop 110

21-** Ext. Closed Loop 111

22-** Application Functions 113

23-** Timed Actions 115

25-** Cascade Controller 116

26-** Analog I/O Option MCB 109 118

7. Troubleshooting

121

Warning/Alarm list 123

8. Specifications

129

General Specifications 129

Special Conditions 138

Purpose of derating 138

Automatic adaptations to ensure performance 141

Index

142

Contents VLT

HVAC Drive Operating Instructions

MG.11.A4.02 - 09.10.06. VLT®is a registered Danfoss trademark

1. Safety

1.1.1. Symbols

Symbols used in this Operating Instructions.

NB!

Indicates something to be noted by the reader.

Indicates a general warning.

Indicates a high-voltage warning.

* Indicates default setting

1.1.2. High Voltage Warning

The voltage of the frequency converter is dangerous whenever it is connected to

mains. Incorrect installation of the motor or frequency converter may cause damage

to the equipment, serious injury or death. Consequently, it is essential to comply

with the instructions in this manual as well as local and national rules and safety

regulations.

Installation at high altitudes:

At altitudes above 2 km, please contact Danfoss Drives regarding PELV.

1.1.3. Safety Instructions

• Make sure the frequency converter is properly connected to earth.

• Do not remove mains connections, motor connections or other power connections while

the frequency converter is connected to mains.

• Protect users against supply voltage.

• Protect the motor against overloading according to national and local regulations.

• Motor overload protection is included in the default settings. Parameter 1-90

Motor ther-

mal protection

is set to value

ETR trip.

For the North American market: ETR functions

provide class 20 motor overload protection, in accordance with NEC.

• The earth leakage current exceeds 3.5 mA.

• The [OFF] key is not a safety switch. It does not disconnect the frequency converter from

mains.

VLT

HVAC Drive Operating Instructions 1. Safety

MG.11.A4.02 - 09.10.06. VLT®is a registered Danfoss trademark

1.1.4. General Warning

Warning:

Touching the electrical parts may be fatal - even after the equipment has been dis-

connected from mains.

Also make sure that other voltage inputs have been disconnected, (linkage of DC

intermediate circuit), as well as the motor connection for kinetic back-up.

Before touching any potentially live parts of the VLT

HVAC Drive FC 100, wait at

least as follows:

200 - 240 V, 1.1 - 3.7 kW: wait at least 4 minutes.

200 - 240 V, 5.5 - 45 kW: wait at least 15 minutes.

380 - 480 V, 1.1 - 7.5 kW: wait at least 4 minutes.

380 - 480 V, 11 - 90 kW, wait at least 15 minutes.

525 - 600 V, 1.1 - 7.5 kW, wait at least 4 minutes.

Shorter time is allowed only if indicated on the nameplate for the specific unit.

Leakage Current

The earth leakage current from the VLT

HVAC Drive FC 100 exceeds 3.5 mA. Ac-

cording to IEC 61800-5-1 a reinforced Protective Earth connection must be ensured

by means of: a min. 10mm² Cu or 16mm² Al PE-wire or an addtional PE wire - with

the same cable cross section as the Mains wiring - must be terminated separately.

Residual Current Device

This product can cause a D.C. current in the protective conductor. Where a residual

current device (RCD) is used for extra protection, only an RCD of Type B (time de-

layed) shall be used on the supply side of this product. See also RCD Application

Note MN.90.GX.02.

Protective earthing of the VLT

HVAC Drive FC 100 and the use of RCD's must always

follow national and local regulations.

1.1.5. Before Commencing Repair Work

1. Disconnect the frequency converter from mains

2. Disconnect DC bus terminals 88 and 89

3. Wait at least the time mentioned in section 1.1.6

4. Remove motor cable

1.1.6. Special conditions

Electrical ratings:

The rating indicated on the nameplate of the frequency converter is based on a typical 3-phase

mains power supply, within the specified voltage, current and temperature range, which is ex-

pected to be used in most applications.

The frequency converters also support other special applications, which affect the electrical ratings

of the frequency converter.

Special conditions which affect the electrical ratings might be:

Single phase applications

High temperature applications which require de-rating of the electrical ratings

Marine applications with more severe environmental conditions.

Other applications might also affect the electrical ratings.

1. Safety VLT

HVAC Drive Operating Instructions

MG.11.A4.02 - 09.10.06. VLT®is a registered Danfoss trademark

Consult the relevant clauses in these instructions and in the

VLT® HVAC Drive Design Guide

for

information about the electrical ratings.

Installation requirements:

The overall electrical safety of the frequency converter requires special installation considerations

regarding:

Fuses and circuit breakers for over-current and short-circuit protection

Selection of power cables (mains, motor, brake, loadsharing and relay)

Grid configuration (IT,TN, grounded leg, etc.)

Safety of low-voltage ports (PELV conditions).

Consult the relevant clauses in these instructions and in the

VLT® HVAC Drive Design Guide

for

information about the installation requirements.

VLT

HVAC Drive Operating Instructions 1. Safety

MG.11.A4.02 - 09.10.06. VLT®is a registered Danfoss trademark

1.1.7. Caution

Caution

The frequency converter DC link capacitors remain charged after power has been disconnec-

ted. To avoid an electrical shock hazard, disconnect the frequency converter from the mains

before carrying out maintenance. Wait at least as follows before doing service on the fre-

quency converter:

Voltage Min. Waiting Time

4 min. 15 min.

200 - 240 V

1.1 - 3.7 kW 5.5 - 45 kW

380 - 480 V 1.1 - 7.5 kW 11 - 90 kW

525 - 600 V 1.1 - 7.5 kW

Be aware that there may be high voltage on the DC link even when the LEDs are turned off.

1.1.8. Installation at High Altitudes (PELV)

By altitudes above 2 km, please contact Danfoss Drives regarding PELV.

1.1.9. Avoid unintended Start

While the frequency converter is connected to mains, the motor can be started/stopped using

digital commands, bus commands, references or via the Local Control Panel.

• Disconnect the frequency converter from mains whenever personal safety considerations

make it necessary to avoid unintended start.

• To avoid unintended start, always activate the [OFF] key before changing parameters.

• Unless terminal 37 is turned off, an electronic fault, temporary overload, a fault in the

mains supply, or lost motor connection may cause a stopped motor to start.

1. Safety VLT

HVAC Drive Operating Instructions

MG.11.A4.02 - 09.10.06. VLT®is a registered Danfoss trademark

1.1.10. Safe Stop of the Frequency Converter

For versions fitted with a Safe Stop terminal 37 input, the frequency converter can perform the

safety function

Safe Torque Off

(As defined by draft CD IEC 61800-5-2) or

Stop Category 0

(as

defined in EN 60204-1).

It is designed and approved suitable for the requirements of Safety Category 3 in EN 954-1. This

functionality is called Safe Stop. Prior to integration and use of Safe Stop in an installation, a

thorough risk analysis on the installation must be carried out in order to determine whether the

Safe Stop functionality and safety category are appropriate and sufficient. In order to install and

use the Safe Stop function in accordance with the requirements of Safety Category 3 in EN 954-1,

the related information and instructions of the VLT

HVAC Drive Design Guide MG.11.BX.YY must

be followed! The information and instructions of the Operating Instructions are not sufficient for

a correct and safe use of the Safe Stop functionality!

130BA491

Illustration 1.1: A similar certificate will be made available for the FC 102!

VLT

HVAC Drive Operating Instructions 1. Safety

MG.11.A4.02 - 09.10.06. VLT®is a registered Danfoss trademark

1.1.11. IT Mains

IT Mains

Do not connect 400 V frequency converters with RFI-filters to mains supplies with a

voltage between phase and earth of more than 440 V.

For IT mains and delta earth (grounded leg), mains voltage may exceed 440 V be-

tween phase and earth.

Par. 14-50

RFI 1

can be used to disconnect the internal RFI capacitiors from the RFI filter to

ground. If this is done it will reduce the RFI performance to A2 level.

1.1.12. Software Version and Approvals: VLT HVAC Drive

VLT HVAC Drive

Operating Instructions

Software version: 2.0X

This Operating Instructions can be used for all VLT HVAC Drive frequency converters with

software version 2.0X.

The software version number can be seen from parameter 15-43.

1.1.13. Disposal Instruction

Equipment containing electrical components may not be disposed of

together with domestic waste.

It must be separately collected with Electrical and Electronic waste

according to local and currently valid legislation.

1. Safety VLT

HVAC Drive Operating Instructions

MG.11.A4.02 - 09.10.06. VLT®is a registered Danfoss trademark

2. Introduction

2.1. Introduction

2.1.1. Frequency Converter Identification

Below is an example of an identification label. This label is situated on the frequency converter

and shows the type and options fitted to the unit. See table 2.1 for details of how to read theType

code string (T/C).

Illustration 2.1: This example shows an identification label.

Please have T/C (type code) number and serial number ready before contacting Danfoss.

VLT

HVAC Drive Operating Instructions 2. Introduction

MG.11.A4.02 - 09.10.06. VLT®is a registered Danfoss trademark

2.1.2. Type Code String

Description Pos Possible choice

Product group & VLT Series 1-6 FC 102

Power rating 8-10 1.1 - 90 kW (1K1 - 90K)

Number of phases 11 Three phases (T)

Mains voltage 11-12

T 2: 200-240 V AC

T 4: 380-480 V AC

T 6: 525-600 V AC

Enclosure 13-15

E20: IP20

E21: IP 21/NEMA Type 1

E55: IP 55/NEMA Type 12

E66: IP66

P21: IP21/NEMA Type 1 w/backplate

P55: IP55/NEMA Type 12 w/backplate

RFI filter 16-17

H1: RFI filter class A1/B

H2: Class A2

H3:RFI filter A1/B (reduced cable length)

Brake 18

X: No brake chopper included

B: Brake chopper included

T: Safe Stop

U: Safe + brake

Display 19

G: Graphical Local Control Panel (GLCP)

N: Numeric Local Control Panel (NLCP)

X: No Local Control Panel

Coating PCB 20 X. No coated PCB

C: Coated PCB

Mains option 21 X: No Mains disconnect switch

1: With Mains disconnect switch (IP55 only)

Adaptation 22 Reserved

Adaptation 23 Reserved

Software release 24-27 Actual software

Software language 28

A options 29-30

AX: No options

A0: MCA 101 Profibus DP V1

A4: MCA 104 DeviceNet

AG: MCA 108 LON works

AJ: MCA 109 BAC Net

B options 31-32

BX: No option

BK: MCB 101 General purpose I/O option

BP: MCB 105 Relay option

BO:MCB 109 Analog I/O

C0 options MCO 33-34 CX: No options

C1 options 35 X: No options

C option software 36-37 XX: Standard software

D options 38-39 DX: No option

D0: DC back-up

Table 2.1: Type code description.

The various options are described further in the

VLT® HVAC Drive Design Guide

2. Introduction VLT

HVAC Drive Operating Instructions

MG.11.A4.02 - 09.10.06. VLT®is a registered Danfoss trademark

Andere Handbücher für VLT HVAC

Inhaltsverzeichnis

Andere Danfoss Gleichstromantrieb Handbücher

Danfoss

Danfoss VLT HVAC Drive FC 102 Bedienungsanleitung

Danfoss

Danfoss VLT CANopen MCA 105 Betriebsanleitung

Danfoss

Danfoss vlt aqua Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 300 Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 360 Benutzerhandbuch

Danfoss

Danfoss VLT PROFINET MCA 120 Bedienungsanleitung

Danfoss

Danfoss VLT AutomationDrive FC 360 Bedienungsanleitung

Danfoss

Danfoss VLT FC 103 Leitfaden

Danfoss

Danfoss VLT Active Front End AFE 302 Bedienungsanleitung

Danfoss

Danfoss VACON 100 industrial Bedienungsanleitung

Danfoss

Danfoss VLT FC 103 Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

Danfoss

Danfoss VLT 2800 Bedienungsanleitung

Danfoss

Danfoss VLT HVAC Drive FC 102 Bedienungsanleitung

Danfoss

Danfoss ADAP-KOOL Drive Betriebsanleitung

Danfoss

Danfoss VLT HVAC FC 100 Bedienungsanleitung

Danfoss

Danfoss VLT HVAC Basic Drive FC 10 Bedienungsanleitung

Danfoss

Danfoss VLT Micro Drive FC 51 Series Leitfaden

Danfoss

Danfoss VLT AutomationDrive FC 301 Bedienungsanleitung

Danfoss

Danfoss vlt aqua Bedienungsanleitung

Danfoss

Danfoss VLT Decentral FCD 300 Bedienungsanleitung

Danfoss

Danfoss VLT Micro Drive FC 51 Series Betriebsanleitung

Danfoss

Danfoss VLT HVAC Drive FC 102 Bedienungsanleitung

Danfoss

Danfoss FC 100 Series Betriebsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch