Danfoss TP5001 series Bedienungsanleitung

TP5001 Range

Electronic Programmable Room Thermostat

Danfoss Heating

MAKING MODERN LIVING POSSIBLE

Installation Guide

Installation Instructions

Important note RF products: Ensure that there are no large metal objects, such as boiler cases

or other large appliances, in line of sight between the transmitter and receiver as these will

prevent communication between thermostat and receiver.

Product Speciﬁcation

Please Note:

This product should only be installed by a qualiﬁed electrician

or competent heating installer and should be in accordance

with the current edition of the IEEE wiring regulations.

Thermostat features TP5001 (A) TP5001-RF TP5001M (A)

Power supply 2 x AA/MN1500/LR

alkaline cells

230V, ±15%,

50Hz

Memory back-up Retained for life of product

Temperature Range

Sensing

5-30°C

Factory set calendar clock Automatic summer/winter time change

Switching action of

output relay

3(1)A,

10-230V

N/A 3(1)A, 10-230V,

Type 1B

Transmission frequency

(RF models)

N/A 433.92MHz N/A

Transmission range

(RF models)

N/A 30m max. N/A

Remote sensor inputs

(A models only)

Can be set by installer for remote temperature sensor,

limit sensor, window contact or telephone activated

switch contacts

Dimensions (mm) 110 wide, 88 high, 28 deep

Design standard EN60730-2-9 (EN300220 for RF)

Rated impulse voltage 2.5kV

Ball hardness test 75°C

Control pollution

situation

Degree 2

Temperature accuracy ±1°C

Time accuracy ±1 min. per month

Installation Instructions

Installation

• First, remove the wallplate from the back of the unit.

• From the top left hand corner of the wallplate, there must be

clearances of at least 15mm to the right, 15mm to the left, 30mm

above and 100mm below in order to mount the plug-in module.

• Thermostat and Remote Room Sensor:

Fix at a height of approximately 1.5m from the ﬂoor, away from

draughts or heat sources such as radiators, open ﬁres or direct

sunlight.

• Prior to mounting the unit the 2 DIL switches on the rear of the

unit have to be moved to the required position. The factory

presets are shown below.

Keyboard disabled

Reset disabled Reset enabled

Keyboard enabled

OFF ON

Sw. No.

Installation Instructions

!Some existing thermostats will have a Neutral and/or Earth wire connected. These

are not required by the TP5001 (battery models) and must NOT be connected to any

TP5001 terminals. Instead they should be made electrically safe and coiled in the

recess at the back of the TP5001.

Cable Access

Wiring - TP5001

Models with remote sensor inputs

TP5001A and TP5001MA incorporate an input which can be used to

connect one of the following:

1) remote room temperature sensor (sold as accessory).

Battery Installation

When installing the batteries in the TP5001 and TP5001 RF please

ensure that the correct polarity is observed as per the markings on the

inside of the battery compartment.

Important: After installing the batteries press and release the RESET

button to start the unit. The display may appear blank until this is

done. Once the button is released the display will appear. All date, time,

programming and override settings are maintained for the life of the

product.

123

Output Connections,

all hard wired models

NDE

S1 S2

Remote Sensor

(A version only)

M 230V Models

Models with remote sensor inputs

Terminal block for remote control/sensing

is located on the circuit board above the

battery compartment.

RX1 RX2 & RX3

1234

ELECTRONICS

COM ZONE

1 ON

ZONE

1 OFF

ELECTRONICS

BC123456

NLZONE

1 ON

ZONE

1 OFF

ZONE

2 ON

ZONE

3 ON

COM

TERMINAL 6

RX3 ONLY

RX Receiver Wiring (RF models only)

1) For mains voltage operated systems link terminal 2 to mains live supply.

2) Power supply to unit must not be switched by timeswitch.

Installation Instructions

S1/D

S2/E

S1/D

S2/E

Window or

teleswitch

contact

(NO or NC)

Teleswitch

contact (NC)

Window

contact (NC)

S1/D

S2/E

Conﬁgured for

remote room

sensor or limit

sensor

Conﬁgured for

window contact or

other contact such

as teleswitch

Conﬁgured for

window contact

and other contact

such as teleswitch

Remote

control

connections

2) limit sensor, for example, ﬂoor temperature sensor (sold as

accessory).

3) window contacts, card reader contacts or teleswitch contacts.

See Installer Advanced Programming Options for set-up instructions.

Commissioning (RF models only)

If the thermostat and the receiver have been supplied together in

a combined pack, the units have been paired in the factory and no

commissioning is required (RX1 only).

To tune the RX receiver to the frequency of the thermostat signal, follow

steps 1-5 below.

Step 1 TP5001-RF

Reset the unit by pressing the recessed

reset button.

Step 2 Press and hold V and + buttons for 3

seconds (TP5001-RF now transmits unique

signal continuously for 3 minutes).

Step 3 RX1

Press and hold buttons PROG and CH1 for

3 seconds until green light ﬂashes once.

Step 4 RX2 (if applicable)

Stat 1 - perform steps 1-3 and 5.

Stat 2 - perform steps 1-2 and then press PROG and CH2 on RX2.

RX3 (if applicable)

Stat 1 - perform steps 1-3 and 5.

Stat 2 - perform steps 1-2 and then press PROG and CH2 on RX3 then

step 5.

Stat 3 - perform steps 1-2 and then press PROG and CH3 on RX3.

Step 5 TP5001-RF

Press V or Λto select temperature - the unit will revert back to operating

mode.

Installation Instructions

GB IMPORTANT

To ensure that the factory programmes are set and the micro-

computerisoperatingcorrectlyit isessentialthatyoupressand

hold the RESET button before you begin any commissioning or

programming.

Installation Instructions

Installer advanced

programming options

TP5001 incorporates a number of advanced features which can be

set by the user. These are accessed via a User Advanced Programming

Mode, please refer to User Advanced Programming in the user

instructions for details.

Installer advanced programming options

TP5001 incorporates an additional number of advanced features which

can be set by the installer to improve the operating eﬃciency of the

system and where required, to change the user functionality of the

product. These are accessed via an Installer Advanced Programming

Mode. These settings are optional and need only be made if there is a

demand for the enhanced functions.

Entering Installer Advanced Programming mode

To access the Installer Advanced Programming

Mode follow the steps below:

a) Press and hold Vand PROG for 3 seconds to

enter User Advanced Programming, the display

will change to ﬁgure opposite.

b) Press and hold V, Λand PROG for 5 seconds

to enter Installer Advanced Programming, the

display will change to ﬁgure opposite.

c) Use +and -keys to scroll backwards and forwards between options

then Vand Λkeys to change the option settings. The ﬂashing digit

on the right hand of the display indicates the number of the selected

option. The large characters display the option value selected.

d) To return to RUN, press and hold PROG until colon in the display

blinks.

Installation Instructions

GB Option 30 - Set upper limit of temperature range

This allows the upper limit of the thermostat

setting range to be electronically limited. Press +

until Option 30 is displayed, use Vand Λto select

required setting.

Setting 40 - 5°C (Factory setting is 30°C)

Option 31 - Set lower limit of temperature range

This allows the lower limit of the thermostat

setting range to be electronically limited. Press +

until Option 31 is displayed, use Vand Λto select

required setting.

Setting 5 - 40°C (Factory setting is 5°C)

Option 32 - Enable Oﬀ at lower limit

This enables an OFF function to be selected if a set

point below the lower limit is selected. Press +until

Option 32 is displayed, use Vand Λto select required

setting.

Setting 0 Disabled

Setting 1 Enabled (factory setting)

Option 33 - Enable On at upper limit

This enables an ON function to be selected if a set

point above the upper limit is selected. Press +until

Option 33 is displayed, use Vand Λto select required

setting.

Setting 0 Disabled (factory setting)

Setting 1 Enabled

Option 34 - Select on/oﬀ or chrono-proportional

This allows the thermostat to be set to run in On/Oﬀ

mode or for a chrono-proportional cycle rate to be

selected. Press +until Option 34 is displayed, use V

and Λto select required setting.

0On/Oﬀ

33 cycles per hour

66 cycles per hour (factory setting)

99 cycles per hour

12 12 cycles per hour

Installation Instructions

Option 35 - Set integration time (Option 34 set to 3, 6, 9 or 12)

(seek advice prior to adjusting)

This adjusts the integration time of the PI

algorithm to increase control accuracy. It should

only be adjusted after seeking advice from the

manufacturer. Press +until Option 35 is displayed,

use Vand Λto select required setting.

2.5 Integration time set to 2.5% (factory setting)

5Integration time set to 5%

10 Integration time set to 10%

Option 36 - Set temperature override rule

This establishes the degree of temperature override

available to the user. Press +until Option 36 is

displayed, use Vand Λto select required setting.

Setting 0 No limit (factory setting)

Setting 1 Limited to ±2°C

Setting 2 No override allowed

Installation Instructions

Option 38 - Relay state on low battery detect

(battery products only)

This establishes the position that the relay is driven

to when the unit shuts down due to low battery

state. Press +until Option 38 is displayed, use Vand

Λto select required setting.

Setting 0 Relay parked with output OFF (factory setting)

Setting 1 Relay parked with output ON

Option 37 - Set time duration of override rule

(Option 36 set to 1 or 2)

This establishes the duration of a temperature

override available to the user. Press +until Option

37 is displayed, use Vand Λto select required

setting.

Setting 0 Next event (factory setting)

Setting 1 1 hour

Setting 2 2 hours

Setting 3 3 hours

Setting 4 4 hours

Option 40 - Number of Events per Day

This sets the thermostat to operate with either 2,

4 or 6 switching events per day or to run it in stat

mode. Press +until option 40 is displayed, use Λ or

Vto select required setting.

1Stat mode

2Two switching events per day

4Four switching events per day

6Six switching events per day (Factory setting)

Andere Handbücher für TP5001 series

Inhaltsverzeichnis

Sprachen:

Andere Danfoss Thermostat Handbücher

Danfoss

Danfoss Icon Master Controller 24 V Bedienungsanleitung

Danfoss

Danfoss HC8000 Series Bedienungsanleitung

Danfoss

Danfoss RET MD Fehlerbehebungshandbuch

Danfoss

Danfoss RT2-RF Bedienungsanleitung

Danfoss

Danfoss ST-S2 Bedienungsanleitung

Danfoss

Danfoss FHV-R Bedienungsanleitung

Danfoss

Danfoss TP4000 Range Bedienungsanleitung

Danfoss

Danfoss FP715Si Bedienungsanleitung

Danfoss

Danfoss RET1000 B Bedienungsanleitung

Danfoss

Danfoss 088U0212 Bedienungsanleitung

Danfoss

Danfoss ECtemp 330 Bedienungsanleitung

Danfoss

Danfoss TP5000 RF Si Leitfaden

Danfoss

Danfoss RAS-C2 Combi Bedienungsanleitung

Danfoss

Danfoss EFET 130 Bedienungsanleitung

Danfoss

Danfoss DEVI DEVIreg 532 Bedienungsanleitung

Danfoss

Danfoss 103E5 Bedienungsanleitung

Danfoss

Danfoss EFIT 540 Bedienungsanleitung

Danfoss

Danfoss RESD Series Bedienungsanleitung

Danfoss

Danfoss TS715 Si Montageanleitung

Danfoss

Danfoss HC75A-1 Betriebsanleitung

Danfoss

Danfoss DEVIreg 530 Bedienungsanleitung

Danfoss

Danfoss TP4000 Range Bedienungsanleitung

Danfoss

Danfoss LX205T Bedienungsanleitung

Danfoss

Danfoss RET M Betriebsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung