Danfoss Type CFR Bedienungsanleitung

RoomThermostat

User Guide

Type CFR

Temperature setting

Set room temperature on the thermostat dial.

On the right-hand side of the thermostat is a

function switch with 3 possible settings:

The room temperature will be as set

on the thermostat.

The control system must have a CFZ

programmer, put thermostat switch

into this position to engage the pro-

grammer. The temperature will be as

set on the room thermostat, but in ac-

cordance with the consumption pattern

entered.

The heating pattern in the programmer

can be overridden by moving the

switch to or .

The room temperature will be as set

on the thermostat less a setback of

5°C/9°F.

Limitation of the setting range

Behind the dial for temperature setting are two lock-

rings. These can be moved as shown if the thermo-

stat setting range is to be narrowed.

Warning: Changes or modifications to this unit not

expressly approved by the party responsible for

compliance could void the user’s authority to operate

the equipment.

(70°F)

FCC ID: PGBTYPE-CFR , CAN 3934104209

This device complies with Part 15 of the FCC Rules and

with RSS-210 of Industry Canada:

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired operation.

Setback

5°C (9°F)

088R0228

Li 3,6V/1,9Ah

088R0228 DKCD 03/01

Registration field in

CFM

RoomThermostat

Instructions for Installation

Type CFR

Each room thermostat has a unique ID number

preventing conflicts with other thermostats. A single

room thermostat is capable of regulating several

heating outputs, provided these outputs are assigned to

the thermostat.

Assigning thermostats to output(s)

-The installation cable between room thermostat and

CFM (fig. 1) must be connected in assigning each

thermostat to the respective output(s).

-IntheLED array the firstavailable position will flash.

Outputs already assigned will not be lit (fig. 2). By

pressing OK the thermostat will be assigned to that

output. If the room thermostat is to be assigned under

another lit output, scroll to the output bymeansof the+/-

keys,then press OK.

-When the installation cable is removed, the red LED

underneath the battery cover (fig. 1) will flash for at

least one minute (Test mode).

Removal of assigned thermostat

-It is not necessary to have the installation cable in

place when removing an assigned thermostat. Once a

thermostat has been removed, it may be reassigned to

another output.

-Removal of room thermostat is done by pressing OK

for 5 seconds, then the entire LED array will be lit.

Scroll to the specific room thermostat to be removed

with the +/- button,and press OK for 5 seconds. The

thermostat has now been removed.

Test of room thermostat

If a defect in a room thermostat is suspected, the fol-

lowing test may be carried out:

- Set the thermostat to the highest temperature.

- Move the function switch on the side of the room ther-

mostat to a new position.

- If the LED underneath the battery cover (fig. 1) flashes

quickly for 3 minutes, the room thermostat is OK.

Inhaltsverzeichnis

Andere Danfoss Thermostat Handbücher

Danfoss

Danfoss TP5001 series Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 310 Bedienungsanleitung

Danfoss

Danfoss TP9 Bedienungsanleitung

Danfoss

Danfoss ECtemp 316 Bedienungsanleitung

Danfoss

Danfoss Link DBR Bedienungsanleitung

Danfoss

Danfoss RAVV-RAV8 Bedienungsanleitung

Danfoss

Danfoss RAS-C2 Combi Bedienungsanleitung

Danfoss

Danfoss ST-S2 Bedienungsanleitung

Danfoss

Danfoss HC75-3 Betriebsanleitung

Danfoss

Danfoss DEVIreg 531 Bedienungsanleitung

Danfoss

Danfoss DEVIreg Opti Bedienungsanleitung

Danfoss

Danfoss Eco Bedienungsanleitung

Danfoss

Danfoss RET2000B-RF Bedienungsanleitung

Danfoss

Danfoss RET 230 HC-1 Bedienungsanleitung

Danfoss

Danfoss FH-RT Handbuch

Danfoss

Danfoss RET 230LS Bedienungsanleitung

Danfoss

Danfoss Icon Master Controller 24 V Bedienungsanleitung

Danfoss

Danfoss TP75M Bedienungsanleitung

Danfoss

Danfoss EFET 130 Bedienungsanleitung

Danfoss

Danfoss TP75 Bedienungsanleitung

Danfoss

Danfoss REP24CO Bedienungsanleitung

Danfoss

Danfoss TP4000 Range Bedienungsanleitung

Danfoss

Danfoss TP7000-RF Verdrahtungsschema

Danfoss

Danfoss RET1000 B Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung