De Agostini Model Space T-72 Bedienungsanleitung
BUILD AND DRIVE THE RADIO-CONTROLLED MODEL
№ 10 SCALE 1:16
CONTENTS
Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP.
Published in the UK by De Agostini UK Ltd, Battersea Studios 2, 82 Silverthorne Road, London SW8 3HE.
Published in the USA by De Agostini Publishing USA, Inc.,121 E. Calhoun Street, Woodstock, IL 60098.
All rights reserved © 2017
Warning: Not suitable for children under the age of 14.
is product is not a toy and is not designed or intended for use in play.
Items may vary from those shown.
STAGE PAGE
50 The smoke generator switch 119
51 The smoke generator liquid 121
52 The diorama building front 123
53 The cones and antenna 125
54 The diorama receiver 127
55 The charger 129
T-72 TANK: STAGE
PB 119
50
PARTS
For this stage,you will need the parts supplied, as well as the
lower hull, a screwdriver, a wooden board, a small hammer
and the track.
1
1. Smoke generator switch
2. Screws
3. Treads (5 pcs.)
4. Pins (5 pcs.)
THE SMOKE GENERATOR SWITCH
With this stage, you receive the switch to turn the smoke generator on and off. This
will start the process that heats up the smoke liquid, which is then discharged through
the tube at the rear of the hull to simulate the exhaust.
T-72 TANK: STAGE
120 121
Insert the smoke generator switch into
the slot located next to the rear of the
battery box.
Insert a screw into the circled hole. Carefully tighten the screw until it is
holding the switch board to the post. Don’t
overtighten, as that can break the board.
Insert the second screw into the other hole
in the board.
Engage the new section with the end of
your existing track.
Carefully tighten the second screw.
Place the track on its side and hammer the
pins into place.
Combine the treads supplied with
this stage.
This stage is now complete.
2 3 4
5 6
9
7
108
T-72 TANK: STAGE
120 121
51
PARTS
To keep the liquid in the container from
evaporating, remove the precision nozzle
and place the cap over the bottle nozzle,
as shown.
You can choose to prepare the bottle
containing the smoke liquid now, or later
when it will be used. Use side cutters to
remove the tip of the bottle nozzle.
For this stage, you will need the parts
supplied, the lower hull, side cutters, a
screwdriver, and the wheel parts received
in Stage 6.
Place the precision nozzle onto the nozzle
on the bottle. This will allow you to be more
accurate when filling the smoke generator.
4
21
3
1. Smoke generator liquid (bottle)
2. Precision nozzle
THE SMOKE GENERATOR LIQUID
With this stage, you receive the liquid for the smoke generator, which will be
vapourised and discharged from the rear of the hull to simulate the exhaust. The liquid
won’t be needed until the end of the build, but you can prepare the bottle now.
T-72 TANK: STAGE
122 123
Now begin fitting the road wheels.Take the
spring from the road wheel set and insert
the perpendicular end into the hole in the
recess indicated by the arrow.
Place the suspension bar over the spring,
as shown.
Turn the suspension bar clockwise until the
stopper is positioned to the right of the one
on the hull, as indicated. Now pass the
axle bolt through the hole in the bar.
Secure the bolt by placing a washer onto
the free end on the inside of the lower hull,
followed by a split washer. Then tighten the
nut onto it, using your fingertips.
Tighten the washer screw into the hole in
the suspension bar to secure the wheel.
Hold the nut in place with a finger, a
wrench or pliers, and tighten the bolt with
a screwdriver.
Press the hub cap into the recess in the
centre of the wheel.
Now place the two halves of the wheel
onto the suspension bar, as shown.
This stage is now complete.
5 6 7
8 9
12
10
1311
T-72 TANK: STAGE
122 123
52
PARTS
For this stage, you will need the parts supplied, the lower hull,
a screwdriver, and the wheel parts received in Stage 8.
1
1. Building front
2. Screws (6 pcs.)
THE DIORAMA BUILDING FRONT
With this stage, you receive the first part of the diorama – the building front. This
diorama will serve as a practice range when complete. For now, continue fitting
road wheels to the lower hull.
T-72 TANK: STAGE
124 125
Half-tighten the six screws into the posts
in the rear of the building front, to avoid
losing them.
Take the spring from the road wheel set and
insert the perpendicular end into the hole in
the recess indicated by the arrow.
This is how the spring should look.
Place the suspension bar over the spring, as
shown, turning it clockwise until the stopper
is positioned to the right of the one on the
hull, circled. Then pass the axle bolt through
the hole in the bar.
Then mount the outer part of the wheel.
Secure the bolt by placing a washer, a split
washer and a nut onto the free end on the
inside of the lower hull. Hold the nut in place
and tighten the bolt with a screwdriver.
Tighten the washer screw into the hole in the
suspension bar to secure the wheel in place.
Press the hub cap into the recess in the
centre of the wheel.
Place the inner part of the wheel on the
bar, as shown.
This stage is now complete.
2 3 4
5 6
9
7
108
T-72 TANK: STAGE
124 125
53
PARTS
For this stage, you will need the parts supplied, the turret, the
lower hull, a screwdriver, and the wheel parts received in
Stage 12.
1
1. Cones (4 pcs.)
2. Antenna base
3. Nut
4. Antenna bottom
5. Antenna top
THE CONES AND ANTENNA
With this stage, you receive a set of cones you can use to create routes to help
develop your driving skills, as well as the display antenna. This antenna doesn’t
actually function as one, so is an optional fit, but can be used as a flag pole or in
places where one is required.
T-72 TANK: STAGE
126 127
If you want to install the antenna, remove
the gun barrel rotor from the inside of the
turret (reverse the steps in Stage 39).
Place the nut from this stage into the
circled hole.
Screw the antenna base into this hole
(circled), while holding the nut in place
on the inside.
Carefully connect the two parts of the
antenna together.
Place both parts of the wheel onto the bar
and secure with a washer screw.
Tighten the antenna into the base to test-fit
it. To avoid damaging it, remove it for now.
Re-fit the gun barrel rotor.
Press the hub cap into the recess in the
centre of the wheel.
Fit the spring into the next hole, then
place the suspension bar over it, turning
it clockwise until the stopper is positioned
to the right of the one on the hull. Pass the
axle bolt through the hole and secure with
a washer, split washer and nut.
This stage is now complete.
2 3 4
5 6
9
7
108
Andere Handbücher für Model Space T-72
9
Andere De Agostini Spielzeug Handbücher
De Agostini
De Agostini Model Space IJN Akagi Bedienungsanleitung
De Agostini
De Agostini Model Space T-72 Bedienungsanleitung
De Agostini
De Agostini Model Space ROBI Pack 03 Bedienungsanleitung
De Agostini
De Agostini Model Space D51 200 Bedienungsanleitung
De Agostini
De Agostini Model Space HUMMER H1 Bedienungsanleitung
De Agostini
De Agostini Model Space T-72 Bedienungsanleitung
De Agostini
De Agostini Model Space C57 Bedienungsanleitung
De Agostini
De Agostini Model Space C57 Bedienungsanleitung
De Agostini
De Agostini Model Space T-72 Bedienungsanleitung
De Agostini
De Agostini MODEL SPACE SUZUKI GSX 1300R HAYABUSA Bedienungsanleitung
De Agostini
De Agostini Model Space H.M.S. Bounty Admiralty Bedienungsanleitung
De Agostini
De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung
De Agostini
De Agostini Model Space MiG-29 Bedienungsanleitung
De Agostini
De Agostini Model Space SANTISIMA TRINIDAD Bedienungsanleitung
De Agostini
De Agostini Model Space MiG-29 Bedienungsanleitung
De Agostini
De Agostini Model Space MiG-29 Bedienungsanleitung
De Agostini
De Agostini Model Space MiG-29 Bedienungsanleitung
De Agostini
De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung
De Agostini
De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung
De Agostini
De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung
