De Agostini Model Space C57 Bedienungsanleitung

Build the

Steam

Locomotive

Pack 02

Contents

Stage 05: The front deck

Stage 06: The feedwater system

Stage 07: The release lever

Stage 08: The inspection lids

Stage 09: The front deck parts

Stage 10: The main underframe

Stage 11: The main underframe front

Stage 12: The cylinder plates

Step by step Pages

Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP.

Published in the UK by De Agostini UK Ltd, Battersea Studios 2, 82 Silverthorne Road, London SW8 3HE.

Published in the USA by De Agostini Publishing USA, Inc., 915 Broadway, Suite 609, New York, NY 10010.

Warning: Not suitable for children under the age of 14. is product is not a toy and is not designed or intended for use in play. Items may vary

from those shown.

Build the

Steam

Locomotive

Step by step: Stage

Tools

Where your parts t

The front deck base ts onto the

projecting tab at the bottom of the

smokebox.

Test-t the front deck base onto

the tab, aligning the circled

holes of both.

Front deck Front deck side

Your parts

The front deck

Front deck base

Front deck upper plate

Front left deck side

Front right deck side

3 screws 2 × 4mm

Phillips screwdriver

Multi-purpose adhesive

Instant adhesive

2 3

Remove the deck base and apply some

multi-purpose adhesive to the tab.

You can

apply instant

adhesive to

the ends of

the screws to

ensure they

stay in position.

Before the glue dries, move

the deck to the left and right,

trying to get it as close to the

smokebox as possible.

This stage is now complete. It is best to store

the assembly on a raised surface, such as the

top of a box, as shown above and on the far

right. The photo on the right shows how the

remaining parts will t together.

Align the holes of the deck with those

in the tab. Half-tighten a 2 × 4mm

screw into each hole.

Once the deck

is in its best

position, fully

tighten the screws

into place.

The sides of the front deck and running board are

painted white on the real C57. White pieces are supplied

to recreate this paintwork on the model.

Tip

Complete

Step by step: Stage

Tools

Where your parts t

The feedwater

system

Feedwater heater body

Feedwater heater end A

Feedwater heater end B

Feedwater heater holder

Feedwater heater upper plate

7 screws 2 × 2mm

3 screws 2 × 4mm

Phillips screwdriver

Multi-purpose adhesive

Epoxy adhesive

The feedwater heater body has a narrow

end and a wide end, as indicated above.

Feedwater heater end B goes in the wide

end and feedwater heater end A ts into

the narrow end.

Glue end B into the wide end of

the feedwater heater with multi-

purpose adhesive.

You will now need

the smokebox

assembly from the

previous stage.

Glue end A to the narrow end of the

feedwater heater.

Feedwater heater Feedwater heater holder

Wide

Narrow

Your parts

To avoid the screwdriver

damaging any of the

adjacent surfaces, you

can cover the shank

with masking tape,

as shown.

If it is hard to tighten

screws into any of

the six screw holes

in the front deck

(circled), you can

use the screwdriver

to remove some of

the paint from the

surface.

Place the two bands

of the feedwater

heater holder over the

feedwater heater.

Align the ends of the two

bands with the two slots in

the front deck.

Pass the bands through the

slots in the front deck.

If the bands won’t enter the slots,

bend them slightly.

Align the holes at the sides of the holder with the

corresponding holes in the deck. Tighten a 2 ×

2mm screw into the lowest of the three holes on

the right-hand side of the holder.

Tighten a 2 × 4mm screw

into the two circled holes

in the underside of the

deck, securing the heater.

Tighten a 2 × 2mm screw into

each of the three holes on

the left side of the holder.

Tighten another two

2 × 2mm screws into

the circled holes.

Apply glue to the

top of the holder

and place the holder

upper plate onto it,

with the raised lip at

the front.

Before the adhesive dries, move the

plate so it is up against the deck

(dotted line), and in line with the

inner edges of the gaps (red lines).

Slots

Glue

Epoxy adhesive

Apply epoxy adhesive to

the slots where the bands

pass through.

Adjust the position of the

bands to be ush with the

heater.

Tips

Complete

Step by step: Stage

Tools

Where your parts t

The release lever

Release lever bar

Release levers A × 2

Release levers B × 2

Front end beam Multi-purpose adhesive

Instant adhesive

接着剤を使い分ける

This picture shows the

dierence between a release

lever A, on the left, and a

release lever B, on the right.

Release lever

Place the four release levers onto the release lever

bar, alternating their order, as shown below.

Front end beam

This is how the

release lever

bar should look,

with the levers

positioned A, B,

A, B, from the

left to right.

Your parts

接着剤を使い分ける接着剤を使い分ける

2 3

The three glues used in this series are all dierent, as

detailed below:

This glue takes time to dry, and so remains

malleable for a while after application. This

also allows excess to be removed easily.

This liquid glue dries almost instantly,

allowing you to place the parts in position

and then apply it to the join between them.

When using instant adhesive/superglue, the excess can sometimes

dry a whitish colour, and because it dries so quickly it can be hard to

remove excess from the surface. You can use hand cream to remove

the excess whitened superglue.

Sometimes instant

adhesive/superglue

will cause whitening

when it dries, as

shown above.

Apply a small

amount of the

hand cream to a

cotton swab.

Gently apply the

hand cream to the

whitened areas.

This slow-drying glue is incredibly strong.

As a result, you must remove any excess

before it dries.

Apply some multi-purpose

adhesive to the two pins

on one of the levers.

Insert the pins of the lever into the

corresponding holes in the front

end beam. Then repeat for the other

three levers.

If any excess adhesive is visible

on the front end beam around

the levers, use something

pointed – such as a toothpick –

to remove it before it dries.

Multi-

purpose

adhesive

Instant

adhesive/

superglue

Epoxy

adhesive

Apply some instant adhesive to the rear of the holes housing the pins of the

levers, to make sure they are secured.

Tips Tips

Complete

Step by step: Stage

Tools

Where your parts t

The inspection lids

Inspection lid A

Inspection lid B

Steps × 4

Hanging brackets × 2

3 screws 2 × 5mm

11 screws 2 × 3mm

Phillips screwdriver

Multi-purpose adhesive

Apply a small amount of multi-

purpose adhesive to the projecting

parts of inspection lid A. Have two

of the steps ready.

Place the two

steps onto the

projecting parts

of the lid.

Inspection lids Steps

Repeat this process to prepare

inspection lid B.

A B

Your parts

2 3

Insert the two hanging brackets into the

rectangular holes in the underside of the

front deck.

Insert the front left deck side (Stage

5) between the front deck and the

inspection lid.

Tighten a 2 × 5mm screw into the holes behind

the bracket in the front deck (arrowed).

Tighten three 2 × 3mm screws into

the holes at the side of the deck

(circled) and then fully tighten

the screws in the two inner holes

(marked here with squares). Repeat

this for the front right deck side.

Align the holes

at the rear of

the front beam

with those in the

brackets.

Align the three holes of the deck

side with those in the front deck

and inspection lid.

Place inspection

lid B into place

from behind the

front deck.

Place the front deck upper plate (Stage

5) onto the front deck.

Position the upper plate so that

the holes align with those in the

front deck.

Front deck base

Front deck upper plate

Insert and

partially tighten

a 2 × 3mm

screw into each

of the two inner

holes (arrowed)

to hold the lid

in place. Repeat

for inspection

lid A.

Complete

Andere Handbücher für Model Space C57

Andere De Agostini Spielzeug Handbücher

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung

De Agostini

De Agostini Model Space C57 Bedienungsanleitung

De Agostini

De Agostini Model Space T-72 Bedienungsanleitung

De Agostini

De Agostini Model Space MiG-29 Bedienungsanleitung

De Agostini

De Agostini Model Space T-72 Bedienungsanleitung

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung

De Agostini

De Agostini Model Space C57 Bedienungsanleitung

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung

De Agostini

De Agostini Model Space MiG-29 Bedienungsanleitung

De Agostini

De Agostini Model Space MiG-29 Bedienungsanleitung

De Agostini

De Agostini Model Space T-72 Bedienungsanleitung

De Agostini

De Agostini Model Space T-72 Bedienungsanleitung

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung

De Agostini

De Agostini Model Space C57 Bedienungsanleitung

De Agostini

De Agostini Millennium Falcon 3 Series Bedienungsanleitung

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Bedienungsanleitung

De Agostini

De Agostini MODEL SPACE SUZUKI GSX 1300R HAYABUSA Bedienungsanleitung

De Agostini

De Agostini Model Space SANTISIMA TRINIDAD Bedienungsanleitung

De Agostini

De Agostini MODEL SPACE Soleil Royal Bedienungsanleitung

De Agostini

De Agostini Model Space MiG-29 Bedienungsanleitung

De Agostini

De Agostini Model Space T-72 Bedienungsanleitung

De Agostini

De Agostini Model Space C57 Bedienungsanleitung

De Agostini

De Agostini Model Space T-72 Bedienungsanleitung

De Agostini

De Agostini Model Space T-72 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung