DeFelsko PosiTector DPM Bedienungsanleitung

Simple. Durable. Accura e.

www.defelsko.com

DeFelsko Corporation USA 2012

All Righ s Reserved

This manual is copyrigh ed wi h all righ s reserved and may no be

reproduced or ransmi ed, in whole or par , by any means, wi hou

wri en permission from DeFelsko Corpora ion.

DeFelsko, PosiTec or and PosiSof are rademarks of DeFelsko

Corpora ion regis ered in he U.S. and in o her coun ries. O her brand

or produc names are rademarks or regis ered rademarks of heir

respec ive holders.

Every effor has been made o ensure ha he informa ion in his manual

is accura e. DeFelsko is no responsible for prin ing or clerical errors.

Quick Guide v. 3.1

PosiTector®

DPM

Dew Point Meter

Introdu tion

The PosiTector Dew Point Meter (DPM) is a hand-held,

electronic instrument that measures, calculates and records

climatic conditions, quickly and accurately. It consists of a body

(Standard or Advanced) and probe (Built-In or Separate).

This Quick Guide summarizes the basic functions of the Gage.

Download the full instruction manual at:

www.defelsko.com/manuals.

The PosiTector DPM powers-up when the center navigation

button is pressed. Readings are updated automatically each

second. To preserve battery life, the instrument powers down after

approximately 5 minutes of no activity. All settings are retained.

Qui k Start

1. Remove the protective rubber cap from the surface

temperature sensor.

2. Power-up Gage by pressing the center navigation button.

Scroll through

Trend Charts

(Advanced only)

Access the Menu

Pause / Resume

Restore brightness

after dimming

(Advanced only)

Button Fun tions- Normal Operation

RH - Relative Humidity (measured)

Ta - Air Temperature (measured)

Ts - Surface Temperature (measured)

Td - Dew Point (calculated)

Ts-Td - Surface minus Dew Point

Temperature (calculated)

Tw - Wet Bulb Temperature (calculated)

(Advanced Models Only)

A typical instrument screen is shown below, consisting of RH, Ta,

Ts, Td, and Ts-Td readings. This group of readings is referred to as

a dataset.

To disconnect a probe from a body, power-down the

instrument and pull the plastic probe connector

horizontally (in the direction of the arrow) away from the

body. Reverse these steps to attach a new probe.

When powered-up the PosiTector automatically

determines which probeis attached and does a

self-check.

Additionally, the PosiTector accepts a number of probe types

including magnetic and eddy current coating thickness, surface

profile, environmental and ultrasonic wall thickness probes.

For the latest information on probe interchangeability, see

www.defelsko.com/probes

Probes

The Pause/Resume (+) button stops values from automatically

updating to allow for closer examination of the relationship

between the values or to allow time to manually record the entire

dataset. Press (+) again to resume.

Down

Center

To navigate, use the Up and Down buttons to

scroll and to SELECT.

Select Exit to exit from any menu.

Navigation Button

The center button is purposely recessed to help

eliminate unintentional powering-up of the gage.

Menu Operation

Gage functions are menu controlled. To access the Menu, power-

up the gage, then press the center navigation button.

NOTE:

Standard models will alert the user when the surface

temperature is less than 3°C (5°F) above the dew point

temperature. Enable by selecting the tick box.

The PosiTector DPM can automatically alert the user when

current climatic conditions exceed pre-set values. When selected,

the Alarm icon is displayed at the the top of the screen.

Advanced models allow the user to set up custom alarm

conditions for each reading in a dataset.

Alarm Mode

Alarm

NOTE:

- Bluetooth Pairing info is cleared.

- Alarm settings are set to defaults.

- Menu settings are returned to the following:

Setup Menu

Reset

Reset (soft reset) restores factory settings and returns the

instrument to a known condition. The following occurs:

- All batches and stored datasets are erased.

- Menu settings are returned to the following:

Memory = OFF

Auto Log = OFF

Bluetooth = OFF

Trend Chart = None

Units = Celsius

Flip Display = Normal

Auto Syn = OFF

Alarms = OFF

Alarm Sound = OFF

Wet Bulb = OFF

White on Bla k = OFF

Language = English

Battery Type = Alkaline

Ba klight = Normal

Auto Log Interval = 5 min

Bluetooth Streaming = OFF

USB Drive= ON

Date, Time and WiFi are not affected by either Reset.

Perform a more thorough Hard Reset by powering down the

instrument, waiting several seconds, then simultaneously holding

both the center and (+) buttons until the Reset symbol

appears. This returns the instrument to a known, “out-of-the-box”

condition. It performs the same function as a menu Reset with the

addition of:

Wet Bulb

When selected, the wet bulb temperature (Tw) is displayed on the

main screen. It is calculated from Ta and RH using an air pressure

of 1.0 atmospheres (1013 mbar). Variations of Tw at other

pressures could be greater than ±1°C (±2°F).

This menu item only appears when all memory functions

are turned off. Wet Bulb readings cannot be stored in memory.

NOTE:

(Advanced models only)

Displays a real-time graph of the readings over

the last three minutes. Use Trend Charts to

monitor short-term environmental changes and

spot trends.

Press the Up button to scroll through

the trend charts.

Trend charts can only be displayed when memory is off.

Trend Chart

Shortcut:

(Advanced models only)

NOTE:

Selects the type of batteries used in the Gage from a choice of

“Alkaline”, “Lithium” or “NiMH” (Nickel-metal hydride

rechargeable). If NiMH is selected, the gage will trickle charge the

batteries while connected via USB to a PC or optional AC charger.

The battery state indicator icon is calibrated for the selected

battery type. No damage will occur if the wrong battery type is

selected.

DeFelsko recommends the use of eneloop (NiMH)

rechargeable batteries.

Battery Type

NOTE:

Advanced models store 20,000 datasets in up to 1,000 batches.

“New Batch” closes any open batch and creates a new batch name

using the lowest available number. The icon appears. New

batch names are date stamped when they are created.

Auto Log Mode

Memory Management

The PosiTector DPM has internal memory storage for recording

measurement datasets. Stored datasets can be reviewed

on-screen or accessed via computers, tablets and smart phones.

Datasets are date and time-stamped. Datasets can be stored

manually (using the (+) button), or automatically using the Auto

Log mode (Page 5).

Standard models store up to 2,500 datasets in one batch.

The PosiTector DPM can automatically display and record

datasets at user selected time intervals. When selected, the Auto

Log icon will appear on the display, with a countdown timer

until the next reading. Connect the instrument to a USB power

source for long-term use.

Turn on instrument/

Cancel Auto Log

mode

Scroll through

display modes

(Advanced only)

Screen Capture

Press both (-)(+) buttons at any time to capture and save an image

copy of the current display. The last 10 screen captures are stored

in memory and can be accessed when connected to a computer

(see PosiSoft USB Drive pg. 6).

Scroll through display

modes (Advanced only)

Delete last reading

Access the Menu

Store a dataset in memory

(Advanced only)

Restore brightness after

dimming (Advanced only)

Standard models remain powered-up while in auto log mode.

The instrument will take readings for 40-50 hours on a set of

alkaline batteries, depending on the frequency of measurements.

Advanced models power down between readings to conserve

batteries. At each interval, the instrument will wake up, take a

reading, sync to PosiTector.net (if configured) and power down.

The instrument can record approximately 8,000 datasets while in

this mode using alkaline batteries, or approximately one dataset

every hour for eight months.

-Auto Log continues recording until memory is full, the instrument

loses power, or the user turns off Auto Log mode. Stored datasets

will remain in memory.

-To conserve battery life, readings update only at the Log Interval.

The last recorded readings will remain “frozen” on the display until

the next dataset has been stored.

-It is recommended that fresh alkaline batteries be installed prior

to an extended Auto Log.

NOTES:

A essing Stored Measurements Data

PosiSoft solutions for viewing, analyzing and reporting data:

PosiSoft USB Drive - connect the PosiTe tor to a PC/Mac using

the supplied USB cable to access and print stored readings, graphs,

photos, notes and screen captures. No software or internet

connection required. USB Drive (pg. 7) must be selected.

PosiSoft.net - a free web-based application offering secure

centralized storage of PosiTe tor readings. Access your data from

any web connected device. Go o: www.PosiSof .ne

PosiSoft Software - Desktop Software for downloading, viewing

and printing your measurement data.

PosiSoft Mobile (Advanced models only) - access readings, graphs,

capture photos and update annotations through WiFi enabled

devices, such as tablets, smart phones and computers.

Auto SYNC

Allows the Gage to automatically synchronize with PosiSof .ne

when initially connected to the internet via a PC running PosiSof

Desk op Manager or a local WiFi network.

Additional measurements added to memory while connected are

synchronized only when the USB cable is disconnected, then

reconnected or when the Syn Now option is selected.

When selected, Gage immediately synchronizes stored

measurement data via USB, Bluetooth or WiFi to PosiSof .ne .

(PosiSof Desk op Manager and an in erne connec ion are

required when using USB or Blue oo h.)

Syn Now

Conne t Menu

The Gage uses a USB mass storage device class which provides

a simple interface to retrieve data in a manner similar to USB flash

drives, cameras or digital audio players.

USB Drive

When connected, power is supplied through the USB

cable. The batteries are not used and the body will not

automatically power down. If rechargeable (NiMH) batteries are

installed, the Gage will trickle charge the batteries.

Allows individual readings to be sent to a computer, printer or

compatible device as they are taken using Bluetooth wireless

technology. See www.defelsko.com/bluetooth

Bluetooth (Advanced models only)

The Gage may perform a Hard Reset after an

update (see pg. 3)

Updates

Determines if a software update is available for your Gage.

See www.defelsko.com/update

Allows wireless communication with devices such as tablets,

smart phones and computers connected to your local wireless

network or portable mobile hot spot. See www.defelsko.com/WiFi

WiFi (Advanced models only)

NOTE:

WARNING:

Te hni al Data

Conforms to: ISO 8502-4, BS7079-B and ASTM D3276

Range A ura y Resolution

Surface

Temperature

-40° to 80° C

80° to 190° C

-40° to 175° F

175° to 375° F

±0.5° C

±1.5° C

±1° F

±3° F

0.1° C

0.1° F

Air

Temperature

-40° to 80° C

-40° to 175° F

±0.5° C

±1° F

0.1° C

0.1° F

Humidity 0 to 100% ±3 % 0.1 %

Operating

Range

-40° C to +80° C

-40° F to +175° F

To ensure optimal performance of your PosiTector DPM,do not

obstruct the airflow near the air temperature and humidity sensors.

eep fingers away from the sensor, as body heat can cause

incorrect readings. Allow time for the instrument to acclimate and

for the readings to stabilize when moving the instrument between

different environments.

When using the surface temperature probe, do not use excessive

downward force, and do not drag it sideways. When the instrument

is not in use, place the rubber cap over the surface temperature

sensor to prevent damage.

CAUTION:

www.defelsko. om

or part, by any means, without written permission from DeFelsko Corporation.

DeFelsko and PosiTector are trademarks of DeFelsko Corporation registered in the U.S. and in other

countries. Other brand or product names are trademarks or registered trademarks of their respective

holders.

Every effort has been made to ensure that the information in this manual is accurate. DeFelsko is not

responsible for printing or clerical errors.

Limited Warranty, Sole Remedy

and Limited Liability

DeFelsko's sole warranty, remedy, and liability are the express

limited warranty, remedy, and limited liability that are set forth on

its website: www.defelsko.com/terms

Returning for Servi e

Before returning the instrument for service…

1.Install new batteries in the proper alignment as shown within

battery compartment.

2.Examine the surface temperature sensor for dirt or damage.

3.Perform a Hard Reset.(see pg. 3)

If you must return the Gage for service, describe the problem fully

and include measurement results, if any. Be sure to also include

the probe, your company name, company contact, telephone

number and fax number or email address.

Website: www.defelsko.com/support

Andere Handbücher für PosiTector DPM

Inhaltsverzeichnis

Sprachen:

Andere DeFelsko Messgerät Handbücher

DeFelsko

DeFelsko PosiTest AIR Bedienungsanleitung

DeFelsko

DeFelsko PosiTector SHD Standard Bedienungsanleitung

DeFelsko

DeFelsko PosiTector 200 Bedienungsanleitung

DeFelsko

DeFelsko PosiTector 200 Bedienungsanleitung

DeFelsko

DeFelsko PosiTector BHI Bedienungsanleitung

DeFelsko

DeFelsko PosiTest DFT Bedienungsanleitung

DeFelsko

DeFelsko PosiTector RTR 3D Bedienungsanleitung

DeFelsko

DeFelsko PosiTest PC Bedienungsanleitung

DeFelsko

DeFelsko PosiTector UTG Bedienungsanleitung

DeFelsko

DeFelsko PosiTector SPG Bedienungsanleitung

DeFelsko

DeFelsko PosiTector UTG Bedienungsanleitung

DeFelsko

DeFelsko PosiTest AT-A Bedienungsanleitung

DeFelsko

DeFelsko PosiTector 6000 Bedienungsanleitung

DeFelsko

DeFelsko POSITECTOR SMARTLINK Bedienungsanleitung

DeFelsko

DeFelsko PosiTector DPM Bedienungsanleitung

DeFelsko

DeFelsko PosiTest AT 50 mm C1583 Kit Montage- und Bedienungsanleitung

DeFelsko

DeFelsko PosiTector SHD Bedienungsanleitung

DeFelsko

DeFelsko PosiTector PC Bedienungsanleitung

DeFelsko

DeFelsko PosiTest CMM Bedienungsanleitung

DeFelsko

DeFelsko PosiTector SPG Bedienungsanleitung

DeFelsko

DeFelsko PosiTector BHI Bedienungsanleitung

DeFelsko

DeFelsko PosiTector6000 Bedienungsanleitung

DeFelsko

DeFelsko DF-SPG3-E Bedienungsanleitung

DeFelsko

DeFelsko PosiTector SHD Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung