Defiant DFI-0452-WH Bedienungsanleitung

THANK YOU

We appreciate the trust and confidence you have placed in Defiant through the purchase of this motion security light.

We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of

products available for your home improvement needs. Thank you for choosing Defiant!

Item #1002638550

Model #DFI-0452-WH

USE AND CARE GUIDE

MOTION SOLAR SECURITY LIGHT

Questions, problems, missing parts? Before returning to the store,

call Defiant Customer Service

8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday

1-866-308-3976

HOMEDEPOT.COM

Table of Contents

Table of Contents..................................2

Safety Information.................................2

Warranty.................................................2

Pre-Installation ......................................3

Installation .............................................6

Operation ...............................................9

Maintenance ........................................12

Care and Cleaning ..............................12

Troubleshooting ..................................12

Safety Information

PRECAUTIONS

Please read and understand this entire manual

before attempting to assemble, install, or operate

this light fixture.

□ This light fixture should be installed

outdoors to a wall or eave.

□ The light fixture should be mounted

approximately 8 ft. (2.4 m) above the

ground.

□ Do not cut the solar panel wire. Discontinue

use if the wire becomes frayed or broken.

□ Do not immerse components in liquid.

□ Do not use any other charging device other

than the single solar charging panel

provided with this light. Doing so may

result in injury or damage to the light and

voids any warranty.

□ Position the cord so that it is securely

fastened and will not result in a hazard

(such as tripping).

□ The maximum extension cord length to use

with this product is 60 ft.

A 30 ft. extension cord is available for this

product at HOMEDEPOT.COM.

WARNING: To prevent possible SERIOUS INJURY

or DEATH, never allow small children near batteries.

If a battery is swallowed, immediately notify a

doctor.

WARNING: DO NOT DISPOSE OF BATTERIES IN

FIRE. BATTERIES MAY EXPLODE OR LEAK.

NOTICE: When replacing batteries, recycle used batteries or

dispose of them in accordance with local regulations.

Warranty

1-YEAR LIMITED WARRANTY

WHAT IS COVERED

This product is guaranteed to be free of factory defective parts and workmanship for a period of 1 year from date of

purchase. Purchase receipt is required for all warranty claims.

WHAT IS NOT COVERED

This guarantee does not include repair service, adjustment and calibration due to misuse, abuse or negligence.

Unauthorized service or modification of the product or of any furnished component will void this warranty in its

entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use,

unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components

that a customer uses in conjunction with this product.

No service parts available for this product.

Contact the Customer Service Team at 1-866-308-3976 or visit www.HomeDepot.com.

3 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Pre-Installation

PLANNING INSTALLATION

Before installing the light fixture, ensure that all parts are present. Compare parts with the Hardware Included and

Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this

light fixture.

Estimated installation time: 30 minutes

PRODUCT DESCRIPTION

This light operates from a battery charged from a solar panel. If the Lithium Ion battery voltage runs down to 3.6V,

the light will automatically switch to ECO mode and dim down to reserve battery for a longer run time. When the

solar panel has recharged the Lithium battery and voltage above 3.7V, the light will automatically switch back to

AUTO mode, and normal brightness.

INITIAL BATTERY CHARGE

IMPORTANT: Clouds, rain, snow, and other weather conditions may not allow the solar panel to completely recharge the battery. Other

obstructions such as buildings or trees may block the sun as well.

When installing the solar panel, make sure it is aimed as described below with a minimum amount of obstructions. Please mount the panel facing

toward the southern sky. An extended solar panel cord is available at Homedepot.com.

□ PRIOR TO USE, the battery will require 2 to 3 days of full, direct sunlight to completely charge with the switch in

the OFF position. Connect the solar panel cord plug with the connector extending from the bottom of the light

housing. If possible, aim the solar panel toward the South and tilt it approximately 50° from horizontal. If the

solar panel cannot be aimed toward the South, then tilt the panel approximately 30°. Another option is to add an

extension cord (excluded in the package) available at Homedepot.com.

□ Actual operating time will vary depending upon how frequently the light is turned on by the motion sensor.

□ Solar lighting is not designed to equal standard 120V lighting. The amount of light output is reduced to allow the

sun time to fully recharge the battery between lighting cycles.

□ Solar collection is only effective in direct sunlight. Every hour the light is on requires a minimum of 6 hours of

sunlight charging.

MOUNTING LOCATION

The most important thing to remember for the operation of your solar powered motion sensing light is that it works

from the power received from direct sunlight. The more direct sunlight the solar panel receives in a day, the longer

the light will operate.

SOLAR LIGHT FIXTURE

The main unit contains the LEDs, a motion sensor, and a rechargeable Lithium battery. When deciding where to

mount this unit, keep in mind that the motion sensor that activates the light has a “field of vision” of 50 ft. (15 m) in

front of the light and about 180° detection angle at a surrounding air temperature of 77°F (25°C).

SOLAR PANEL

The solar panel converts the sun’s energy into electricity, thus charging the battery stored in the solar light fixture.

The solar panel requires direct sunlight falling onto the face of the solar panel for as long as possible over the course

of the day.

When choosing the location for the solar panel, make sure it is aimed toward the South and is tilted to a suitable

angle to allow as much direct sunlight to fall upon it as possible. Make sure there is a minimum amount of

obstructions between the solar panel and the sun.

Also, make sure your solar panel location is not too far away from the solar light fixture for the wires to reach and

connect.

Pre-Installation (continued)

SPECIFICATIONS

Range Up to 50 ft. (15 m) (Varies with surrounding temperature)

Sensing angle Up to 180°

Lumens Solar Power: 500 LM

Power requirements Solar panel and rechargeable Lithium Batteries

Operating modes Off and Auto

Time delay 1 minute to 5 minutes

TOOLS REQUIRED

Safety

goggles

Phillips

screwdriver Level

Drill bits

(3/32 in. and

7/32 in.)

Drill

Ladder

HARDWARE INCLUDED

NOTE: Hardware shown to actual size.

AA BB

Part Description Quantity

AA Mounting screw 5

BB Wall anchor 5

5 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Pre-Installation (continued)

PACKAGE CONTENTS

Part Description Quantity

A Lamp head 2

B Light fixture 1

C Motion sensor 1

D Mounting plate 1

E Power button 1

F Solar panel 1

G Solar panel cradle 1

H Extendable cord (preassembled to Light fixture (B)) 1

I Extendable cord (preassembled from Solar panel (F)) 1

Installation

1 Determining the mounting

location 2 Setting the sensor for wall

or eave mounting

NOTE: The light fixture should be mounted approximately

8 ft. (2.4 m) above the ground.

NOTE: Ensure the fixture and the solar panel are located

close enough together for the cord to reach. You can also

add on an extension cord. Ensure the solar panel faces

South.

□ Determine the mounting location - wall or eave

mount.

□ Position the lamp head (A) in the general direction

of the desired light coverage.

NOTE: Adjust the sensor angle to a coverage

desired.

□ For wall mounting, tilt the sensor (C) down 10

degrees to cover up to a 50 ft. range in front.

□ For eave mounting, turn the sensor (C) either

clockwise or counterclockwise to the desired

position.

Wall Mount

Incorrect

Eave Mount

7 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Installation (continued)

3 Removing the mounting plate 4 Installing the mounting plate

NOTE: Make sure there is enough vertical space above

the mounting plate to allow the light fixture to be mounted.

□ Press the wall mounting plate (D) and slide the

mounting plate (D) from the light body (B).

NOTE: Make sure there is enough vertical space

above the mounting plate to allow the light fixture to

be mounted.

Place the mounting plate (D) against the mounting

surface and ensure the mounting plate (D) is level.

Mark the hole locations on the mounting surface,

through which the mounting screws (AA) will be

threaded.

□ If mounting to a wooden surface, drill two

3/32 in. holes into the mounting surface.

Install the two mounting screws (AA) through

the mounting plate (D) and into the mounting

surface.

□ If mounting to wall board or brick, drill two

7/32 in. holes into the mounting surface.

Insert the wall anchors (BB) and attach the

mounting plate (D) using the two mounting

screws (AA).

5 Mounting the light fixture

□ Slide the rear of the light fixture (B) down onto the

mounting plate (D) until it snaps into place.

Installation (continued)

6 Mounting the solar panel

RECOMMENDED: Caulk around the base and on top of

the screw heads after installation.

Place the solar panel (F) against the mounting surface and

mark the mounting holes.

□ If mounting to a wooden surface, drill three 3/32 in.

holes into the mounting surface. Install the three

mounting screws (AA) through the solar panel

cradle (G) and into the mounting surface.

□ If mounting to wall board or brick, drill three 7/32 in.

holes into the mounting surface. Insert the wall

anchors (BB) and attach the solar panel cradle (G)

using the three mounting screws (AA).

□ Once the solar panel cradle (G) has been installed,

position the solor panel (F) above it, adjusting the

direction and angle of the panel to its desired

position to receive optimal sunlight.

□ Slide the base of the solar panel (F) into the cradle

(G). It will snap and lock in position.

7 Adjusting the solar panel 8 Connecting the solar panel

to the light fixture

IMPORTANT: The solar panel (F) must receive as much

direct sunlight over the course of the day as possible. Keep

in mind that shadows may block the sunlight from reaching

the solar panel (F) during the day.

□ Rotate the solar panel (F) to the desired angle.

□ Carefully connect the solar panel (F) cable to

the light fixture (B). Screw the caps on the

plugs firmly.

□ Wrap any excess solar panel cable around the

cradle (G) located on the rear of the solar

panel (F). Leave enough loose cable to form a

drip loop.

IMPORTANT: Push the switch to the OFF position

and allow the battery to charge with 2 to 3 days of

full sunshine before testing.

9 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Operation

1 Adjusting the lamp heads

□ If needed, gently grasp the lamp heads (A) and tilt

them up or down or side-to-side to adjust the

light coverage area.

2 Using the OFF control

□ Press the power button (E) to turn the light (B) off

and to conserve the battery life.

NOTE: Pushing the button in turns the light (B) ON (AUTO

mode). Pushing again so that the power button is out and

extended turns the light OFF.

Operation (continued)

3 Determining the motion

sensor detection zone

NOTE: The motion sensor (C) is adjustable. It has a

sensing angle of 180° and a range of approximately 50 ft.

depending on the surrounding temperature.

NOTE: When you turn ON the light (B), it will begin a 3

minute test mode. The photocell and motion detection will

be deactivated. After the first minute, motion detection will

be activated, but the photocell will remain deactivated.

After 3 minutes, the unit will set to AUTO mode, and both

photocells and motion detection will be enabled.

NOTE: The motion sensor (C) will need to completely

warm up (60 seconds) before beginning the setup process.

□ Push the switch button to the AUTO position. For the

first minute, the light is in test mode. The lamp heads

will stay on for 1 minute.

□ After the initial minute in test mode, motion detection

will be activated. You will have 2 minutes to perform a

“walk test”, which will help in identifying the coverage

area of the motion sensor (C).

□ Walk in an arc across the front of the motion sensor

(C), and watch the indicator light (1). If the motion

sensor (C) detects movement, the indicator light (1)

will flash green, and the lamp heads will stay on for 30

seconds after the detection (regardless of any further

motion.)

□ After 30 seconds, the indicator light will turn OFF and

reset for another detection. This cycle can be repeated

up to 4 times, and it is recommended that the motion

sensor (C) be adjusted for optimal detection during

these cycles.

□

fter 4 motion test cycles, or 2 minutes after the initial

test mode, the light will automatically switch to AUTO

mode.

4 Adjusting the light timer

NOTE: The TIME dial controls the amount of time the light

(B) will stay on full brightness after motion has been

detected. The timer is adjustable from 1 minute to 5 minutes.

□ To increase the time, turn the TIME dial towards the

5 minute position.

□ To decrease the time, turn the TIME dial towards the

1 minute position.

Andere Handbücher für DFI-0452-WH

Inhaltsverzeichnis

Sprachen:

Andere Defiant Scheinwerfer Handbücher

Defiant

Defiant DFI-0654-WH Bedienungsanleitung

Defiant

Defiant MSH27920DLWD Bedienungsanleitung

Defiant

Defiant DFI-5983-BZ Bedienungsanleitung

Defiant

Defiant DFI-0452-WH Bedienungsanleitung

Defiant

Defiant CD-5928-WH Bedienungsanleitung

Defiant

Defiant DFI-5892-WH Bedienungsanleitung

Defiant

Defiant DFI-7004-WH-G Bedienungsanleitung

Defiant

Defiant K40425002 Bedienungsanleitung

Defiant

Defiant DF-5909-WH Bedienungsanleitung

Defiant

Defiant DFI-5851-BK Bedienungsanleitung

Defiant

Defiant CD-5936-BK Bedienungsanleitung

Defiant

Defiant DFI-0452-WH Bedienungsanleitung

Defiant

Defiant MSLED1801D Bedienungsanleitung

Defiant

Defiant MST18920lwdf Bedienungsanleitung

Defiant

Defiant DFI-7004-WH-G Bedienungsanleitung

Defiant

Defiant DFI-5998-BK Bedienungsanleitung

Defiant

Defiant 5985 Bedienungsanleitung

Defiant

Defiant CD-5928-WH-A Bedienungsanleitung

Defiant

Defiant DFI-5408-GR Bedienungsanleitung

Defiant

Defiant DFI-0452-WH Installations- und Betriebsanleitung

Defiant

Defiant DF-5928-BZ-A Bedienungsanleitung

Defiant

Defiant 1002366429 Bedienungsanleitung

Defiant

Defiant DFI-7167-WH-G Bedienungsanleitung

Defiant

Defiant DF-5939-BK Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung