Dell PowerEdge 1750 Bedienungsanleitung

Dell Poweredge 1750

Installing a ROMB Card (PERC4/DI)

CAUTION: Before you perform this procedure, you must turn off the system and

disconnect it from its power source. For more information, see "Safety First—For

You and Your System" in "Troubleshooting Your System."

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. See your System

Information Guide for complete information about safety precautions, working

inside the computer, and protecting against electrostatic discharge.

NOTICE: To avoid possible data loss, back up all data on the hard drives before changing

the mode of operation of the integrated SCSI controller from SCSI to RAID.

1. Turn off the system, including any attached peripherals, and disconnect the system

from the electrical outlet.

2. Open the system covers. See "Opening the System Covers" in "Troubleshooting Your

System."

3. Locate the ROMB card connector on the system board. See Figure A-3.

4. If a PCI card is installed over the ROMB card connector, remove it. See "Removing an

Expansion Card."

5. Position the ROMB card with the notch in its plastic cover facing the redundant power

supply bay, and align the edges of the card with the four plastic standoffs on the

system board.

6. Press down on the three "bulls eyes" on the ROMB card cover until the four plastic

standoffs snap over the edge of the card. See Figure 6-11.

Figure 6-11. Installing the ROMB Card and Backup Battery

7. Install the ROMB backup battery:

a. Position the battery board as shown in Figure 6-11, and press it down into the

two standoffs until it snaps into place.

b. Plug the battery cable into the RAID BATTERY connector on the system board.

8. If you removed a PCI card in step 4, replace it. See "Installing an Expansion Card."

9. Close the system covers. See "Closing the System Covers" in "Troubleshooting Your

System."

10. Reconnect the system and peripherals to their power sources, and turn them on.

11. Enter the System Setup program and verify that the setting for the SCSI controller has

changed to reflect the presence of the RAID hardware. See "Using the System Setup

Program" in your User's Guide.

12. Install the RAID software. See the ROMB card software documentation for more

information.

Removing a ROMB Card

CAUTION: Before you perform this procedure, you must turn off the system and

disconnect it from its power source. For more information, see "Safety First—For

You and Your System" in "Troubleshooting Your System."

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. See your System

Information Guide for complete information about safety precautions, working

inside the computer, and protecting against electrostatic discharge.

NOTICE: To avoid possible data loss, back up all data on the hard drives before changing

the mode of operation of the integrated SCSI controller from SCSI to RAID.

1. Turn off the system, including any attached peripherals, and disconnect the system

from the electrical outlet.

2. Open the system covers. See "Opening the System Covers" in "Troubleshooting Your

System."

3. If a PCI card is installed over the ROMB card, remove the PCI card. See "Removing an

Expansion Card."

4. Pull the ROMB card up out of the four standoffs. See Figure 6-11.

5. Disconnect the ROMB backup battery from the backup battery connector, and pull the

battery assembly up out of the two standoffs. See Figure 6-11.

6. Close the system covers. See "Closing the System Covers" in "Troubleshooting Your

System."

Andere Handbücher für PowerEdge 1750

7

Inhaltsverzeichnis

Andere Dell Server Handbücher

Dell

Dell PowerEdge T20 Betriebsanleitung

Dell

Dell PowerEdge M910 Kurzanleitung

Dell

Dell PowerEdge T110 Technisches Handbuch

Dell

Dell PowerEdge C6220 Bedienungsanleitung

Dell

Dell PowerEdge C5220 Bedienungsanleitung

Dell

Dell PowerEdge 400SC Technisches Handbuch

Dell

Dell PowerEdge 1550 Technisches Handbuch

Dell

Dell PowerEdge 2950 Bedienungsanleitung

Dell

Dell PowerEdge 6950 Bedienungsanleitung

Dell

Dell PowerEdge 4600 Bedienungsanleitung

Dell

Dell poweredge t330 Bedienungsanleitung

Dell

Dell PowerEdge NX702 Bedienungsanleitung

Dell

Dell PowerEdge 1400SC Technisches Handbuch

Dell

Dell PowerEdge T110 II Kurzanleitung

Dell

Dell PowerEdge M710 Bedienungsanleitung

Dell

Dell Wyse 3020 Fehlerbehebungshandbuch

Dell

Dell EMC PowerEdge R640 Bedienungsanleitung

Dell

Dell Poweredge metered Bedienungsanleitung

Dell

Dell PowerEdge M620 Kurzanleitung

Dell

Dell PowerEdge C8000 Bedienungsanleitung

Dell

Dell PowerEdge R220 Bedienungsanleitung

Dell

Dell 8TTX3 Handbuch

Dell

Dell POWEREDGE 1900 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung