Dell PowerEdge 1800 Technisches Handbuch

www.dell.com | support.dell.com

Dell™ PowerEdge™ 1800 Systems

Information Update

信息更新

Mise à jour des informations

Aktuelle Informationen

アップデート情報

정보 업데이트

Actualización de información

www.dell.com | support.dell.com

Dell™ PowerEdge™ 1800 Systems

Information Update

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how

to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Abbreviations and Acronyms

For a complete list of abbreviations and acronyms, see "Glossary" in your

User’s Guide

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, PowerEdge, and Dell OpenManage are trademarks of Dell Inc.;

Red Hat is a registered trademark of Red Hat, Inc.; Microsoft and Windows are registered trademarks

and Windows Server is a trademark of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks

and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

February 2005 P/N X6447 Rev. A03

Information Update 3

This document provides updated information for your system on the following topics:

• Multiple monitors in display properties

• BIOS version A01

• Adding a second IDE device to the IDE controller cable

• Embedded SATA 2s controller-to-CERC SATA 6-channel upgrade considerations

• Video and cabling considerations for the DRAC 4P expansion card

• Enabling video hardware acceleration in the Microsoft

Windows Server™ 2003

operating system

• Correcting flat-panel display video problems during Microsoft Windows Server 2003

operating system installations

• Power-supply fan performance in system standby mode

• Installing Dell OpenManage™ Array Manager 3.6

• Single memory module installation

• Using a PERC 4/DC controller

• Creating an embedded SATA controller RAID array

• Using Red Hat

Enterprise Linux, Dell OpenManage Server Assistant, and the embedded

SATA controller with RAID

• Installing fast ethernet drivers using Server Assistant on dual-processor systems running

the Microsoft Windows

2000 operating system

Multiple Monitors in Display Properties

Your system has one video connector on the back panel. The video driver installed in your system is

designed to be used with various Dell™ systems, some of which have front- and back-panel video

connectors. This causes the Microsoft Windows Server 2003 operating system to report that the

system is configured to display on multiple monitors.

To check your display settings:

Right-click your desktop and click

Properties

Click the

Settings

tab and verify that the display mode is set to

(Multiple Monitors)

on RADEON 7000 SERIES

The video driver also causes Windows Server 2003 to display the monitor that is attached to your

system’s video connector, as well as to reserve a "default monitor" as a placeholder for systems that

have two video connectors.

To view the list of monitors:

Right-click your desktop and click

Properties

Click the

Settings

tab, and then click the

Advanced

button.

4Information Update

www.dell.com | support.dell.com

Click the

Monitor

tab.

The

Monitor Type

list box displays the monitors attached to your system.

NOTE: If a Remote Access Card (RAC) is installed in your system, the RAC appears as a third video

device in the Monitor Type list box. Use the scroll buttons in the Monitor Type list box to display

any additional monitor types.

NOTE: If Windows Server 2003 cannot identify the monitor type, the operating system identifies

the monitor as a "Plug and Play Monitor."

BIOS Version A01

New features were added to the A01 release of the system BIOS that are not present in the previous

release. As a result, flashing the BIOS back to the earlier release may cause unexpected system

behavior. Dell does not recommend that you revert your system to a previous BIOS release.

Adding a Second IDE Device to the IDE Controller Cable

The system board has one IDE controller and one IDE connector that is normally used to connect

an IDE optical device installed in the 5.25-inch drive bay. The System Setup program provides an

option to enable or disable the IDE controller, and the primary master optical device can be viewed

through the boot order in the System Setup program.

If a second IDE device, such as an IDE tape backup drive, is installed in the 5.25-inch peripheral

bay and is attached to the slave connector of the IDE cable, details of the second device can be

viewed only in the operating system and not the System Setup program.

Embedded SATA 2s Controller-to-CERC SATA 6-Channel

Upgrade Considerations

If you are presently using the embedded SATA 2s controller in a dual hard-drive configuration and

are upgrading to a CERC SATA 6-channel expansion card RAID array, you must first disable and

remove the embedded SATA 2s configuration.

NOTICE: Operating the system in a CERC 6-channel SATA RAID array with the embedded SATA 2s

controller enabled is not a supported configuration and can cause the operating system to malfunction

during shutdowns and other unpredictable results.

Follow the guidelines listed below if you are presently using an embedded SATA 2s controller

configuration and are upgrading to a CERC SATA 6-channel configuration.

Back up the data from the hard drives that the embedded SATA 2s controller is using.

The hard drives must be reinitialized for use with the CERC SATA 6-channel upgrade.

Disable the embedded SATA 2s controller in the System Setup program.

See "Using the System Setup Program" in the

User’s Guide

for additional information.

Information Update 5

Remove the cables from the embedded SATA 2s controller system-board connectors

and the hard drives.

If you purchased additional hard drives with the CERC SATA 6-channel upgrade,

install those hard drives.

See "Installing Drives" in the

Installation and Troubleshooting Guide

for additional information.

Install and configure the CERC SATA 6-channel upgrade.

See "Expansion Cards" in the

Installation and Troubleshooting Guide

and the documentation

that came with the CERC SATA 6-channel upgrade for additional information.

Restore the data that you backed up in step 1 to the new array on the hard drives.

Video and Cabling Considerations for the DRAC 4P

Expansion Card

If your system has a Dell Remote Access Controller 4P (DRAC 4P) expansion card installed,

the monitor must be connected to the video connector on the DRAC 4P card—not to the system’s

integrated video connector. See the

Dell Remote Access Controller 4 User’s Guide

for the location

of the video connector on the DRAC 4P card.

Also, if you add a DRAC 4P card to the system, the card must be installed in slot 4, and the

interface cable that was supplied with the card must be attached from the card to the RAC

connector on the system board. See "System Board Connectors" in the

Installation and

Troubleshooting Guide

for the location of the system board RAC connector.

Enabling Video Hardware Acceleration in the Microsoft

Windows Server 2003 Operating System

By default, video hardware acceleration is set to a low setting by the Microsoft Windows

Server 2003 operating system. Your system’s video controller supports enhanced features and

requires that the video hardware acceleration be set to its highest (

Full

) setting. Operating the

system without adjusting the video hardware acceleration to its highest setting may cause the

system to become unstable under certain conditions. To adjust the video hardware acceleration,

follow these steps:

Click

Start

, point to

Control Panel

, and then click

Display

You can also right-click the desktop, and then click

Properties

Click the

Settings

tab in the

Display Properties

window, and then click

Advanced

Click the

Troubleshoot

tab, and move the hardware acceleration slider to

Full

Click

, and then click

If you reinstall or update the video drivers, or if you reinstall Windows Server 2003, then reset

the video hardware acceleration to its

Full

setting again.

6Information Update

www.dell.com | support.dell.com

Correcting Flat-Panel Display Video Problems During

Microsoft Windows Server 2003 Operating System

Installations

NOTE: The following information applies only to Microsoft Windows Server 2003 operating system

installations on systems that have certain flat-panel displays attached, and console redirection is

enabled in the System Setup program (console redirection is disabled by default). Systems that have a

CRT monitor attached, or systems that are having any other operating system installed, are not affected.

Under certain conditions, the image on some flat-panel displays may roll during the installation of

the Microsoft Windows Server 2003 operating system. This is caused by console redirection being

enabled in the System Setup program (console redirection is disabled by default).

Console redirection is intended for system management from a terminal attached to the system’s

serial port. When Windows Server 2003 detects that console redirection is enabled, it optimizes its

installation screens to a low-resolution text mode for a VT100-compatible terminal. Some flat-

panel displays cannot synchronize to that mode.

To correct the problem, restart the system, enter the System Setup program, and disable console

redirection. After installing the Windows Server 2003 operating system, enter the System Setup

program, and enable console redirection, if desired.

Power-Supply Fan Performance in System Standby Mode

Each power supply contains an internal cooling fan. When the system enters system standby mode,

the power-supply fan remains on. This is normal operation and allows the fan to continue to cool

the power-supply. The fan’s performance may cause the system to appear to be on while the system

is actually turned off in system standby mode.

Installing Dell OpenManage Array Manager 3.6

Dell OpenManage Array Manager 3.6 is provided with your system. Array Manager is designed

for system administrators who implement hardware and software RAID solutions and understand

corporate and small business storage environments. To install Array Manager, perform the

following steps:

Insert the Dell OpenManage CD into the CD drive.

The Dell OpenManage installation application automatically starts.

Exit the Dell OpenManage installation application if you want to install only Array

Manager 3.6.

Navigate to the

am\setup

directory on the CD.

Click

setup.exe

Follow the instructions on the screen.

Array Manager can also be downloaded and installed from

support.dell.com

Information Update 7

Single Memory Module Installation

If only one memory module is installed, it must be installed in socket DIMM1_B. Two-way

interleaving is not supported for this configuration. See the

Installation and Troubleshooting Guide

for more information about memory modules.

Using a PERC 4/DC Controller

Only channel 0 of the PowerEdge™ Expandable RAID Controller 4/DC (PERC 4/DC) is rated for

use with the integrated SCSI controller in your system. Systems shipped from Dell with a

PERC 4/DC controller installed are already configured with the channel-0 connection and this

configuration should not be changed. If you add a PERC 4/DC controller to your system, you must

connect channel 0 of the PERC 4/DC controller to the SCSI backplane using the cable that is

supplied with the controller.

Creating an Embedded SATA Controller RAID Array

To easily create a RAID array when using the system’s embedded SATA controller, perform

the following steps:

Turn on your system.

Press <F2> immediately after you see the following message:

<F2> = Setup

See "System Setup Program" in the

User’s Guide

for additional information.

Enable RAID in the

Integrated Devices

options in the System Setup program.

See your CERC SATA 2s documentation for information on configuring RAID drives.

The CERC SATA 2s RAID driver is available at Dell Support at

support.dell.com

Using Red Hat Enterprise Linux, Dell OpenManage Server

Assistant, and the Embedded SATA Controller With RAID

The Red Hat Enterprise Linux operating system can be installed only by using the Red Hat

Enterprise Linux media if

all

of the following conditions exist:

• You are attempting to use Server Assistant to install Red Hat Enterprise Linux.

• The embedded SATA controller is enabled in the System Setup program

(see the

User’s Guide

for more information about the System Setup program).

This is because Server Assistant does not contain RAID drivers to support a Red Hat Enterprise

Linux operating system installation with the embedded SATA controller enabled in a RAID

configuration at this time. Therefore, the Red Hat Enterprise Linux operating system installation

option is not available in Server Assistant if those conditions listed above exist.

8Information Update

www.dell.com | support.dell.com

See the Red Hat Enterprise Linux documentation for instructions on how to install that operating

system from the Red Hat Enterprise Linux media.

After installing the operating system from the Red Hat Enterprise Linux media, you can use Server

Assistant to install additional utilities, such as diagnostics, if desired.

Considerations When Configuring RAID Using Red Hat Enterprise Linux

and the Embedded SATA Controller

NOTE: The following information applies only if you want to use the embedded SATA controller

in a RAID configuration using Red Hat Enterprise Linux.

NOTICE: The system does not have RAID drivers that support an embedded SATA controller RAID

configuration in a Red Hat Enterprise Linux environment. RAID is not enabled even when the System

Setup program RAID option is enabled. RAID can only be enabled and configured from within the

Red Hat Enterprise Linux operating system.

When using the embedded SATA controller with Red Hat Enterprise Linux, RAID can only be

enabled and configured through the Red Hat Enterprise Linux operating system—not at the

system level.

Although the RAID option can be selected and enabled in System Setup program and

RAID 0 or RAID 1 can be configured in <Ctrl><a>, RAID drivers are not available for its support

and RAID is not enabled.

See the Red Hat Enterprise Linux documentation for instructions on how to enable and configure

RAID.

Installing Fast Ethernet Drivers Using Server Assistant

on Dual-Processor Systems Running the Microsoft

Windows 2000 Operating System

Under certain circumstances, installing the Fast Ethernet drivers using Server Assistant on a system

with dual-processors and running the Microsoft Windows 2000 operating system may halt at the

Plug and Play Detection

screen. If this occurs, restart the system and the installation completes

normally.

Andere Handbücher für PowerEdge 1800

Inhaltsverzeichnis

Sprachen:

Andere Dell Server Handbücher

Dell

Dell EMC VxFlex Ready Node 14G Bedienungsanleitung

Dell

Dell POWEREDGE 4300 Leitfaden

Dell

Dell PowerEdge R7615 Handbuch

Dell

Dell DL4300 Bedienungsanleitung

Dell

Dell 7CX5T Handbuch

Dell

Dell PowerEdge PDU Managed LED Bedienungsanleitung

Dell

Dell PowerEdge 1300 Installations- und Betriebshandbuch

Dell

Dell PowerEdge R220 Kurzanleitung

Dell

Dell PowerEdge M610 Kurzanleitung

Dell

Dell PowerEdge 2900 Bedienungsanleitung

Dell

Dell External M620 t Bedienungsanleitung

Dell

Dell DX6004S Bedienungsanleitung

Dell

Dell PowerEdge M710 Kurzanleitung

Dell

Dell PowerEdge C6600 Handbuch

Dell

Dell PowerEdge M820 Systems Kurzanleitung

Dell

Dell PowerEdge 6800 Bedienungsanleitung

Dell

Dell E14S Series Bedienungsanleitung

Dell

Dell PowerEdge 1650 Leitfaden

Dell

Dell PowerEdge R620 Kurzanleitung

Dell

Dell PowerEdge R630 Bedienungsanleitung

Dell

Dell PowerEdge M1000e Kurzanleitung

Dell

Dell PowerEdge C8000 Datenblatt

Dell

Dell PowerEdge 1855 Leitfaden

Dell

Dell PowerEdge UPS 500T Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch