Dell PowerEdge 2400 Bedienungsanleitung



™









Throughout this guide, blocks of text may be accompanied by an icon and printed in

bold type or in italic type. These blocks are notes, notices, cautions, and warnings,

and they are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of your

computer system.





  !"

"#

$%&$%&!"

"#

____________________

Information in this document is subject to change without notice.

Trademarks used in this text: Dell, PowerEdge, and the DELL logo are trademarks of Dell

Computer Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Dell Computer Corporation disclaims any pro-

prietary interest in trademarks and trade names other than its own.

October 1999 P/N 6648R Rev. A01

Dell PowerEdge 2400 Systems—Activating the Dell PowerEdge Expandable RAID Controller 2/Si 1-1





 

! "#

To activate the integrated PowerEdge Expandable RAID Controller (PERC) 2/Si,

perform the following steps.



 !

"#$%&

'()*+,--.

+/01-+

%&+&,/.!

2&%&2+%

/01-!

3242+

/ 01-+++

#!5+-+565"

" !

1. Turn off and unplug your computer and peripherals.

2. Remove the right-side computer cover.

See “Checking Inside the Computer” in your system Installation and Trouble-

shooting Guide for more information.

3. Remove the cooling shroud.

See “Checking Inside the Computer” in your system Installation and Trouble-

shooting Guide for more information.

4. Press the ejectors on the RAID controller DIMM socket (see Figure 1-1) down

and outward to allow the dual in-line memory module (DIMM) to be inserted into

the socket (see Figure 1-2).

1-2 Dell PowerEdge 2400 Systems—Activating the Dell PowerEdge Expandable RAID Controller 2/Si



1Integrated RAID hardware key connector (RAID_KEY)

2DIMM socket for optional RAID controller (DIMM_RAID)

Dell PowerEdge 2400 Systems—Activating the Dell PowerEdge Expandable RAID Controller 2/Si 1-3



5. Align the DIMM's edge connector with the slot in the center of the DIMM

socket, and insert the DIMM in the socket (see step A in Figure 1-2).

The DIMM socket has two alignment keys that allow the DIMM to be installed in

the socket in only one way.

NOTE: The RAID controller DIMM must be an unbuffered DIMM, rated to run at

100 MHz. Do not substitute registered DIMMs such as those used for system

memory. System memory is labeled “PC133.”

6. Press down on the DIMM with your thumbs while pulling up on the ejectors with

your index fingers to lock the DIMM into the socket (see step B in Figure 1-2).

7. Install the RAID hardware key in its socket on the system board (see Figure 1-1).

Secure the key with the latches on each end of the socket (see Figure 1-3). The

RAID hardware key should be labeled “PE2400.”

1DIMM socket ejectors (2)

2Alignment keys (2)

1-4 Dell PowerEdge 2400 Systems—Activating the Dell PowerEdge Expandable RAID Controller 2/Si

 

8. Replace the cooling shroud and computer cover, and then reconnect the com-

puter and peripherals to their AC power sources and turn them on.

9. Press <F2> immediately after you see the following message:

<F2> = System Setup

If you wait too long and your operating system begins to load into memory, let

the system complete the load operation; then shut down the system and try

again.

For more information on the System Setup program, see “Using the System

Setup Program”in your system User’s Guide.

NOTE: To ensure an orderly system shutdown, consult the documentation that

accompanied your operating system.

10. Press <Alt> <p> to switch to Page 2 of the System Setup screen.

11. If the Onboard RAID option is displayed, select this option.

If the Primary SCSI option is displayed, the integrated RAID controller was not

detected; go to step 1 and repeat all installation steps.

'()*--+

/01-+%&/!

1RAID hardware key

2Latches (2)

3Socket

Dell PowerEdge 2400 Systems—Activating the Dell PowerEdge Expandable RAID Controller 2/Si 1-5

12. Press the left- or right-arrow key to set the Onboard RAID option to RAID.

The default setting for Onboard RAID is SCSI.

13. Press <Alt> <b> to save the settings and reboot the system.

14. Configure the RAID subsystem and install the RAID driver and management

software.

For more information, refer to the integrated PERC 2/Si controller documentation.

1-6 Dell PowerEdge 2400 Systems—Activating the Dell PowerEdge Expandable RAID Controller 2/Si

Andere Handbücher für PowerEdge 2400

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dell Server Handbücher

Dell

Dell PowerEdge R430 Bedienungsanleitung

Dell

Dell PowerEdge R310 Bedienungsanleitung

Dell

Dell EMC PowerEdge R250 Handbuch

Dell

Dell PowerEdge 6350 Bedienungsanleitung

Dell

Dell 8 Bedienungsanleitung

Dell

Dell PowerEdge T105 Systems Allgemeine Anweisungen

Dell

Dell PowerEdge M1000e Bedienungsanleitung

Dell

Dell External OEMR R210II Bedienungsanleitung

Dell

Dell DR4000 Restore Manager Anleitung zur Verwendung

Dell

Dell EMC PowerEdge R350 Handbuch

Dell

Dell PowerEdge SC1420 Betriebsanleitung

Dell

Dell PowerEdge R6615 Handbuch

Dell

Dell POWEREDGE 1900 Bedienungsanleitung

Dell

Dell DR4000 Restore Manager Gebrauchsanweisung

Dell

Dell EMC VxFlex Ready Node 14G Bedienungsanleitung

Dell

Dell PowerEdge 4600 Technisches Handbuch

Dell

Dell PowerEdge C6100 Bedienungsanleitung

Dell

Dell PowerEdge C1100 Kurzanleitung

Dell

Dell PowerEdge R650XS RD8NP Handbuch

Dell

Dell 8TTX3 Handbuch

Dell

Dell PowerEdge R910 Technisches Handbuch

Dell

Dell EMC PowerEdge R550 Bedienungsanleitung

Dell

Dell PowerEdge 1655MC Bedienungsanleitung

Dell

Dell EMC PowerEdge R240 CHRH4 Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung