Dell PowerEdge 2950 Bedienungsanleitung

www.dell.com | support.dell.com

Rack Installation Guide

Guide d'installation du rack

Rack-Installationsanleitung

ラック取り付けガイド

Guía de instalación del rack

Rack Installation Guide

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, RapidRails, and VersaRails are trademarks of Dell Inc.

ther trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

March 2007 P/N TP579 Rev. A00

Contents 3

Contents

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

SAFETY: Rack Mounting of Systems . . . . . . . . . . . . . . . . . . . . . 5

General Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 6

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . 6

Rack Requirements for VersaRails . . . . . . . . . . . . . . . . . . . . . . 6

Rack Stabilizer Feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Recommended Tools and Supplies . . . . . . . . . . . . . . . . . . . . . . 7

Rack Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Removing the Rack Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Marking the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Configuring the Sliding Rail Assemblies . . . . . . . . . . . . . . . . . . . . 11

Installing the Mounting Rails in the Rack . . . . . . . . . . . . . . . . . . . . 12

Installing RapidRails Mounting Rails . . . . . . . . . . . . . . . . . . . . 12

Installing the VersaRails Mounting Rails . . . . . . . . . . . . . . . . . . 13

Installing the System in the Rack . . . . . . . . . . . . . . . . . . . . . . . . 15

Removing the System From the Rack . . . . . . . . . . . . . . . . . . . . 16

Installing the Cable-Management Arm . . . . . . . . . . . . . . . . . . . . . 17

Routing Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Attaching the Cable-Management Arm Ramp Assembly . . . . . . . . . . . . 19

Replacing the Rack Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4Contents

Rack Installation Guide 5

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to help protect your system

and working environment from potential damage. For complete safety and regulatory information, see

the Product Information Guide that shipped with your system. Warranty information might be included

in this document or as a separate document.

SAFETY: Rack Mounting of Systems

Observe the following precautions for rack stability and safety. Also refer to the rack installation

documentation accompanying the system and the rack for specific caution statements and procedures.

Systems are considered to be components in a rack. Thus, "component" refers to any system as well as

to various peripherals or supporting hardware.

CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks or the front

stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before installing systems in

a rack could cause the rack to tip over, potentially resulting in bodily injury under certain circumstances.

Therefore, always install the stabilizer(s) before installing components in the rack.

After installing system/components in a rack, never pull more than one component out of the rack on its slide

assemblies at one time. The weight of more than one extended component could cause the rack to tip over and

may result in serious injury.

NOTE: Your system is safety-certified as a free-standing unit and as a component for use in a Dell rack cabinet

using the customer rack kit. The installation of your system and rack kit in any other rack cabinet has not been

approved by any safety agencies. It is your responsibility to ensure that the final combination of system and rack

complies with all applicable safety standards and local electric code requirements. Dell disclaims all liability and

warranties in connection with such combinations.

• System rack kits are intended to be installed in a rack by trained service technicians. If you install

the kit in any other rack, be sure that the rack meets the specifications of a Dell rack.

CAUTION: Do not move racks by yourself. Due to the height and weight of the rack, a minimum of two people

should accomplish this task.

• Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor,

and that the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack

or front stabilizers for joined multiple racks before working on the rack.

• Always load the rack from the bottom up, and load the heaviest item in the rack first.

• Make sure that the rack is level and stable before extending a component from the rack.

• Use caution when pressing the component rail release latches and sliding a component into or out of

a rack; the slide rails can pinch your fingers.

• Do not overload the AC supply branch circuit that provides power to the rack. The total rack load

should not exceed 80 percent of the branch circuit rating.

• Ensure that proper airflow is provided to components in the rack.

• Do not step on or stand on any component when servicing other components in a rack.

6Rack Installation Guide

General Installation Instructions

This installation guide provides instructions for trained service technicians installing one or more systems in

a rack cabinet. The RapidRails™ configuration can be installed without tools in manufacturer's rack cabinets

that have square holes; the VersaRails™ configuration can be installed in most industry-standard rack

cabinets that have square or round holes. One rack kit is required for each system to be installed in the rack

cabinet.

Before You Begin

Before you begin installing your system in the rack, carefully read "Safety Instructions" on page 5, as well

as the safety instructions found in your Product Information Guide for additional information.

CAUTION: When installing multiple systems in a rack, complete all of the procedures for the current system

before attempting to install the next system.

CAUTION: Rack cabinets can be extremely heavy and move easily on their casters. They do not have brakes. Use

extreme caution while moving the rack cabinet. Retract the leveling feet when relocating the rack cabinet. Avoid

long or steep inclines or ramps where loss of cabinet control may occur. Extend the leveling feet for support and

to prevent the cabinet from rolling.

NOTE: For instructions on installing the system itself, see "Installing the System in the Rack" on page 15.

Important Safety Information

Observe the safety precautions in the following subsections when installing your system in the rack.

CAUTION: You must strictly follow the procedures in this document to protect yourself as well as others who

may be involved. Your system may be very large and heavy and proper preparation and planning are important to

prevent injury to yourself and to others. This precaution becomes increasingly important when systems are

installed high up in the rack.

CAUTION: Do not install rack kit components designed for another system. Use only the rack kit for your system.

Using the rack kit for another system may result in damage to the system and personal injury to yourself and to

others.

Rack Requirements for VersaRails

NOTICE: The VersaRails rack kit is intended to be installed by trained service technicians in a rack that meets the

specifications of American National Standards Institute (ANSI)/Electronic Industries Association (EIA) standard

ANSI/EIA-310-D-92, International Electrotechnical Commission (IEC) 297, and Deutsche Industrie Norm (DIN) 41494.

One rack kit is required for each system that is installed in a rack.

Rack Installation Guide 7

Rack Stabilizer Feet

CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone racks or the front

stabilizer on racks joined to other racks. Failure to install stabilizers accordingly before installing systems in a

rack could cause the rack to tip over, potentially resulting in bodily injury under certain circumstances.

Therefore, always install the stabilizer(s) before installing components in the rack.

The stabilizer feet help prevent the rack from tipping over. See the documentation provided with the rack

cabinet for instructions on installing and anchoring the stabilizer feet.

Recommended Tools and Supplies

You may need the following items to install the system in a four-post rack cabinet:

• #2 Phillips screwdriver

• Masking tape or a felt-tip pen, for use in marking the mounting holes to be used

Rack Kit Contents

• One pair of slide assemblies

• One cable-management arm

• One left cable-management arm ramp assembly

• One right cable-management arm ramp assembly

• One status indicator cable (if applicable)

• Eight 10-32 x 0.5-inch flange-head Phillips screws

NOTE: The nonmetric screws described in illustrations and in procedural steps are identified by size and number

of threads per inch. For example, a #10 Phillips-head screw with 32 threads per inch is identified as a 10-32 screw.

NOTE: Both the right and left cable-management arm ramp assemblies are illustrated in Figure 1-1. Depending on

the orientation of the cable-management arm (CMA), you will only use one ramp assembly to secure the CMA to

the back of the rack. For more information, see "Attaching the Cable-Management Arm Ramp Assembly"

on page 19.

8Rack Installation Guide

Figure 1-1. Rack Kit Contents

Installation Tasks

Installing a rack kit involves performing the following tasks (described in detail in subsequent sections)

in their numbered order:

Removing the rack doors

Marking the rack

Configuring the sliding rail assemblies

Installing the mounting rails in the rack

• RapidRails installation

• VersaRails installation

Installing the system in the rack

Installing the cable-management arm

Routing cables

Attaching the cable-management arm ramp assembly

Replacing the rack doors

1 cable-management arm 2 left cable-management arm

ramp assembly

3 right cable-management arm

ramp assembly

4 slide assemblies 5 10-32 x 0.5-inch flange-head

Phillips screws (8)

6 status indicator cable

(if applicable)

Andere Handbücher für PowerEdge 2950

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Dell Server Handbücher

Dell

Dell PowerEdge 2650 Bedienungs- und Sicherheitshinweise

Dell

Dell 3250 Technisches Handbuch

Dell

Dell PowerEdge HX574 Bedienungsanleitung

Dell

Dell Force10 C150 Bedienungsanleitung

Dell

Dell PowerEdge 4200 Series Bedienungsanleitung

Dell

Dell PowerEdge 6600 Bedienungsanleitung

Dell

Dell PowerEdge R910 Technisches Handbuch

Dell

Dell KGR3H Handbuch

Dell

Dell PowerEdge 1655MC Bedienungsanleitung

Dell

Dell PowerEdge M1000e Bedienungsanleitung

Dell

Dell FC4700 Bedienungsanleitung

Dell

Dell Force10 MXL Blade Bedienungsanleitung

Dell

Dell PowerEdge R620 Bedienungsanleitung

Dell

Dell PowerEdge SC430 Betriebsanleitung

Dell

Dell PowerEdge R320 Bedienungsanleitung

Dell

Dell EMC ScaleIO Ready Node 14G Montageanleitung

Dell

Dell PowerEdge 650 Leitfaden

Dell

Dell PowerEdge 2410 Bedienungsanleitung

Dell

Dell PowerEdge C6220 Bedienungsanleitung

Dell

Dell PowerEdge SE400 Bedienungsanleitung

Dell

Dell DL4300 Bedienungsanleitung

Dell

Dell PowerEdge 2850 Technisches Handbuch

Dell

Dell PowerEdge 1850 Bedienungsanleitung

Dell

Dell 8 Allgemeine Anweisungen

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch