Dell PowerEdge 6600 Bedienungsanleitung

www.dell.com | support.dell.com

Dell™ Systems

Microprocessor Upgrade

Installation Guide

4N560ebk1.book Page 1 Monday, November 25, 2002 12:03 PM

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

Information in this document is subject to change without notice.

Reproductioninanymannerwhatsoever without the written permissionofDellComputerCorporationisstrictlyforbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Computer Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and

names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names

other than its own.

November 2002 P/N 4N560 Rev. A01

4N560ebk1.book Page 2 Monday, November 25, 2002 12:03 PM

Microprocessor Upgrade Installation Guide 1-1

CAUTION: Only trained service technicians are authorized to remove the system

covers and access any of the components inside the system.

CAUTION: The System Information document provides important safety and

regulatory information. Read and follow all safety instructions prior to setup,

operation, and service of your system.

To take advantage of future options in speed and functionality, you can add additional

microprocessors or replace installed microprocessors.

NOTICE: Before you add or replace a microprocessor, check the latest system BIOS

information on the Dell Support website at support.dell.com, and upgrade the BIOS if necessary.

NOTICE: The additional microprocessors must be of the same type as the primary

microprocessor. All microprocessors must also have the same L2 and L3 cache sizes.

Each microprocessor and its associated cache memory are contained in a PGA package that

is installed in a ZIF socket on the microprocessor board.

In a single-microprocessor system, the microprocessor must be installed in the CPU1 socket.

NOTE: A microprocessor and VRM must be installed in the CPU1 and VRM1 sockets,

respectively. To identify the CPU1 and VRM1 sockets, see Figure 1-1.

NOTICE: If a microprocessor socket does not have a microprocessor installed, a heat-sink

blank must be installed for that socket.

The following items are included in the microprocessor upgrade kit:

•A microprocessor

•A heat sink

•A VRM, if you are adding additional microprocessors

Microprocessor and VRM Mixing

Your system does not support mixing processors or VRMs. If you mix processors or VRMs,

the messages in Table 1-1 are displayed during POST.

Table 1-1. System Message

Message Causes Corrective Actions

Mismatch VRMnLatest processor revision with

out-of-date VRMs, or mixed

versions of VRMs

Ensure that you have the correct version

of VRMs installed for the processors in

your system.

Ensure that all VRMs are identical.

VID mismatch nMixed processors Ensure that the processors are the same

version.

4N560ebk1.book Page 1 Monday, November 25, 2002 12:03 PM

1-2 Mircroprocessor Upgrade Installation Guide

www.dell.com | support.dell.com

Adding or Replacing a Microprocessor

CAUTION: Before you perform this procedure, you must turn off the system and

disconnect it from its power source.

NOTICE: See "Protecting Against Electrostatic Discharge" in the safety instructions in your

System Information document.

NOTE: For steps 1 through 5, see your Installation and Troubleshooting Guide for

details.

1Open the bezel.

2Turn off the system, including any attached peripherals, and disconnect the system

from the electrical outlet.

3Remove the back cover.

4Remove the front cover.

5Raise the following components to the service position:

• Memory riser cards

• Peripheral riser card

•Fans

6While grasping the microprocessor tray handles, press the release levers with your

thumbs and rotate the tray handles up until the tray is released from the front panel

(see Figure 1-1).

7Slide the microprocessor tray out until the safety latches lock into place.

8While pressing on the safety latches, pull the microprocessor tray straight out until the

tray clears the chassis.

9Place the microprocessor tray on a flat surface.

10 While holding the tab on the side release lever, rotate the lever up until the cover is

released from the side of the enclosure (see Figure 1-1).

11 While holding the front release lever, rotate the lever up until the cover is released

from the front of the enclosure (see Figure 1-1).

12 Remove the cover.

4N560ebk1.book Page 2 Monday, November 25, 2002 12:03 PM

Microprocessor Upgrade Installation Guide 1-3

Figure 1-1. Removing and Replacing the Microprocessor Cover

CAUTION: The microprocessor and heat sink can become extremely hot. Be sure

the microprocessor has had sufficient time to cool before handling.

NOTICE: Never remove the heat sink from a microprocessor unless you intend to remove the

microprocessor. The heat sink is necessary to maintain proper thermal conditions.

NOTICE: After removing the heat sink, it should be placed upside down on a flat surface to

prevent the thermal interface material from being damaged or contaminated.

13 Remove the heat sink (see Figure 1-1).

14 Pull the socket release lever up until the microprocessor is released (see Figure 1-2).

heat sink

cover retention tabs (2)

side release lever

microprocessor

cover

front release lever

CPU1

VRM1

tray handle

release levers (2)

microprocessor

tray handles (2)

4N560ebk1.book Page 3 Monday, November 25, 2002 12:03 PM

1-4 Mircroprocessor Upgrade Installation Guide

www.dell.com | support.dell.com

Figure 1-2. Removing and Replacing the Microprocessor

NOTICE: Be careful not to bend any of the pins when removing the microprocessor. Bending

the pins can permanently damage the microprocessor.

15 Lift the microprocessor out of the socket and leave the release lever up so that the

socket is ready for the new microprocessor (see Figure 1-2).

16 Unpack the new microprocessor.

If any of the pins on the microprocessor appear bent, see "Getting Help" in the

Installation and Troubleshooting Guide for instructions on obtaining technical

assistance.

17 If the release lever on the microprocessor socket is not all the way up, move it to that

position now.

18 Align the gold triangle on the microprocessor (see Figure 1-2) with the triangle on the

microprocessor socket.

NOTE: Zero insertion force is needed to install the microprocessor. If the microprocessor is

aligned correctly, it should drop into the microprocessor socket.

microprocessor

release lever

pin-1 corners

microprocessor socket

4N560ebk1.book Page 4 Monday, November 25, 2002 12:03 PM

Microprocessor Upgrade Installation Guide 1-5

NOTICE: Positioning the microprocessor incorrectly can permanently damage the

microprocessor and the system when you turn on the system. When placing the microprocessor

in the socket, be sure that all of the pins on the microprocessor go into the corresponding holes.

Be careful not to bend the pins.

19 Apply light pressure to the top of the microprocessor while rotating the socket release

lever down, securing the microprocessor.

20 Place the new heat sink on top of the microprocessor (see Figure 1-1).

21 Orient the microprocessor cover as shown in Figure 1-1.

NOTICE: Failure to properly install the microprocessor cover can permanently damage the

microprocessor(s). When installing the microprocessor cover, ensure that the cover retention

tabs on the edge of the microprocessor enclosure are inserted into the slots of the cover.

22 Hook the end of the cover over the retention tabs on the edge of the microprocessor

enclosure (see Figure 1-1).

23 Swing the microprocessor cover down.

24 Rotate the front release lever down to secure the cover to the front of the

microprocessor enclosure (see Figure 1-1).

25 Rotate the side release lever down to secure the cover to the side of the microprocessor

enclosure (see Figure 1-1).

26 If you are adding additional microprocessors, install the VRM in the corresponding

VRM socket, pushing down firmly to make sure that the ejectors engage (see

Figure 1-3).

27 Slide the microprocessor tray into the chassis until the tray stops.

28 Lift the microprocessor tray handles up and push the tray forward slightly to engage

the handle clasps.

29 Rotate the microprocessor tray handles down until the tray is secured to the front

panel.

NOTE: For steps 30 through 33, see your Installation and Troubleshooting Guide for

details.

30 Reseat the following components:

• Peripheral riser card

• Memory riser cards

• Fans

4N560ebk1.book Page 5 Monday, November 25, 2002 12:03 PM

1-6 Mircroprocessor Upgrade Installation Guide

www.dell.com | support.dell.com

Figure 1-3. Installing the VRM

31 Replace the front cover.

32 Replace the back cover.

33 Close the bezel.

34 Reconnect your system and peripherals to their electrical outlets, and turn on the

system.

As the system boots, it detects the presence of the new microprocessor(s) and

automatically changes the system configuration information in the System Setup

program and displays the microprocessor ID number, operating speed, processor bus,

and cache information.

35 Press <F2> to enter the System Setup program, and check that the microprocessor

categories match the new system configuration (see "Using the System Setup

Program" in your User's Guide).

36 Run the system diagnostics to verify that the new microprocessor is operating

correctly.

See "Running the System Diagnostics" in the Installation and Troubleshooting Guide

for information on running the diagnostics and troubleshooting any problems that

may occur.

VRM

VRM connector

ejectors (2)

alignment key

4N560ebk1.book Page 6 Monday, November 25, 2002 12:03 PM

www.dell.com | support.dell.com

Dell™ 系统

微处理器升级安装指南

4N560cbk1.book Page 1 Monday, November 25, 2002 12:30 PM

注注意和警告

注注表示可以帮助您更好地使用计算机的重要信息

注意注意表示可能会损坏硬件或导致据丢失并告诉您如何避免此类问题

警告警告表示存在可能导致财产损失人身伤害或死亡的潜在危险

本文件中的信息如有更改恕不另行通知

未经 Dell Computer Corporation 书面许可不准以任何形式进行复制

本文件中使用的商标 Dell 和DELL 徽标是 Dell Computer Corporation 的商标

本文件中述及的它商标和产品名称是指拥有相应商标和名称的公司或制造的产品 Dell Computer

Corporation 对它公司的商标和产品名称不拥有任何专利权

2002 年11 月P/N 4N560 Rev. A01

4N560cbk1.book Page 2 Monday, November 25, 2002 12:30 PM

Andere Handbücher für PowerEdge 6600

Inhaltsverzeichnis

Sprachen:

Andere Dell Server Handbücher

Dell

Dell PowerEdge 650 Leitfaden

Dell

Dell PowerEdge C6145 Bedienungsanleitung

Dell

Dell PowerEdge R905 Bedienungsanleitung

Dell

Dell PowerEdge R210 Technisches Handbuch

Dell

Dell PowerEdge C6320 Bedienungsanleitung

Dell

Dell PowerEdge R415 Bedienungsanleitung

Dell

Dell PS4000E Bedienungsanleitung

Dell

Dell PowerApp .cache 100 Technisches Handbuch

Dell

Dell PowerEdge T100 Betriebsanleitung

Dell

Dell PowerEdge T105 Systems Bedienungsanleitung

Dell

Dell PowerEdge SC1425 Leitfaden

Dell

Dell PowerEdge E05S Bedienungsanleitung

Dell

Dell PowerEdge 2410 Bedienungsanleitung

Dell

Dell Dimension 2400 Series Bedienungsanleitung

Dell

Dell PowerEdge R420 Bedienungsanleitung

Dell

Dell PowerEdge R930 Bedienungsanleitung

Dell

Dell PowerEdge HS5610 Handbuch

Dell

Dell PowerEdge 2600 Technisches Handbuch

Dell

Dell POWEREDGE T300 Bedienungsanleitung

Dell

Dell PowerEdge T610 Bedienungsanleitung

Dell

Dell wyse V00 Bedienungsanleitung

Dell

Dell EMC VxFlex Ready Node 14G Bedienungsanleitung

Dell

Dell PowerApp .cache 100 Technisches Handbuch

Dell

Dell PowerEdge 4400 Allgemeine Anweisungen

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch