Dell PowerEdge UPS 500T Bedienungsanleitung

Dell UPS Local Node Manager

USER'S GUIDE EXTENSION FOR MICROSOFT VIRTUAL ARCHITECTURES

Dellups.com

Dell ULNM - User guide extension - HyperV R1 & R2

rev0.01

CHAPTER: Introduction

Microsoft virtual architecture:

Hyper-V 6.0 Manager

Hyper-V Server (R1 & R2)

Main Operating System: 2008Enterprise R2 x64 (hosting Hyper-V)

Hyper-V Manager

Hyper-V Server R1,

Dell UPS Local Node

Manager

Dell UPS Local Node Manager

USER'S GUIDE EXTENSION FOR MICROSOFT VIRTUAL ARCHITECTURES

Dellups.com

Dell ULNM - User guide extension - HyperV R1 & R2

rev0.01

CHAPTER: Introduction

TABLE OF CONTENTS

1. Introduction .................................................................................................................................................... 3

2. Installation ...................................................................................................................................................... 4

2.1. Installation Prerequisites................................................................................................................... 4

2.1.1. Test configuration with Hyper-V Manager........................................................................................ 4

2.1.2. Test configuration with Hyper-V Server R1 & R2 .............................................................................. 4

2.2. Microsoft Hyper-V Manager / Hyper-V Server R1 & R2 configuration.............................................. 5

2.2.1. “Guest Component Service” installation........................................................................................... 5

2.2.2. Services configuration ....................................................................................................................... 5

2.3. Dell Hardware architecture ............................................................................................................. 10

2.4. Network architecture ...................................................................................................................... 10

2.5. Installing Dell ULNM on Hyper-V Server R1 & R2 and Windows Server 2008 R2 (Hyper-V Manager)

2.6. Uninstalling Dell ULNM ................................................................................................................... 12

2.7. Useful commands............................................................................................................................ 12

2.8. Alarms reception ............................................................................................................................. 13

2.9. Using Dell ULNM with Hyper-V Server R1 & R2 or Hyper-V Manager ............................................ 13

2.9.1. Step 1 (Access) ................................................................................................................................ 13

2.9.2. Step 2 (Configuration) ..................................................................................................................... 14

2.9.3. Step 3 (Operation)........................................................................................................................... 15

3. Appendix ....................................................................................................................................................... 16

3.1. References....................................................................................................................................... 16

Dell UPS Local Node Manager

USER'S GUIDE EXTENSION FOR MICROSOFT VIRTUAL ARCHITECTURES

Dellups.com

Dell ULNM - User guide extension - HyperV R1 & R2

rev0.01

CHAPTER: Introduction

1. INTRODUCTION

Dell is a world class supplier of hardware and software optimizing business continuity on your

Microsoft virtual platforms worldwide. The system includes controlling proper boot and graceful

shutdown of:

The virtual machines hosted on a same physical machine.

The main operating system hosting Microsoft Hyper-V or Hyper-V Server.

Dell UPS Local Node Manager is Dell’s solution to automate various data security functions.

It:

Continuously waits for information from the UPS Management Card (Dell PN H910P)

connected to the Dell UPS.

Warns administrators and users if AC power fails

Proceeds to shutdown system before the end of battery backup power is reached.

Restarts machines when AC power restarts.

Microsoft Hyper-V (or Hyper-V Server) controls the Virtual Machine’s shutdown and restart

functions. Dell UPS Local Node Manager can be installed on the main operating system (hosting

Hyper-V).

Dell UPS Local Node Manager will consolidate information from the UPS which is supplying the

server. Advantages of installing our protection software on the main operating system (hosting

Hyper-V) include:

Only one deployment of Dell ULNM on physical machine, to manage all virtual machines.

Silent deployment possibility.

Dynamic management of virtual machines configuration, with a personalized script.

This manual will guide you through the installation and configuration process of the Dell UPS Local

Node Manager on Microsoft Hyper-V (or Hyper-V Server) platform.

Dell tested virtualization security in a redundant power supply configuration, for system shutdown,

electrical shutdown, and reboot.

Dell UPS Local Node Manager

USER'S GUIDE EXTENSION FOR MICROSOFT VIRTUAL ARCHITECTURES

Dellups.com

Dell ULNM - User guide extension - HyperV R1 & R2

rev0.01

CHAPTER: Installation

2. INSTALLATION

This section will guide the user through the installation process of Dell UPS Local Node Manager on

Microsoft Hyper-V architecture. Use of Dell UPS Local Node Manager will allow continuity of the

electrical power supply to the end user’s internal power system.

2.1. INSTALLATION PREREQUISITES

2.1.1. TEST CONFIGURATION WITH HYPER-V MANAGER

This procedure was validated using Microsoft Windows 2008 Enterprise R1, R2 x64 as the main

operating system (hosting Hyper-V). The system had the following applications installed:

Microsoft Hyper-V hosting several virtual machines :

oWindows 2000 Server SP4 and Advanced Server SP4

oWindows Server 2003 x86/x64 R2 SP2

oWindows Server 2008 x86/x64 SP1/SP2

oWindows XP Professional SP2/SP3 and x64 SP2

oWindows Vista SP1/SP2 (except Home editions)

oWindows Seven x86/x64 (except Home editions) (Only On Server 2008 R2)

oSUSE Linux Enterprise Server 10 SP2 & 11

oRed Hat Enterprise Linux 5.2/5.3/5.4 x86/x64

Dell UPS Local Node Manager for Windows.

2.1.2. TEST CONFIGURATION WITH HYPER-V SERVER R1 & R2

This procedure was validated using Hyper-V Server running on an x64 machine.

Microsoft Hyper-V Server was hosting:

oWindows 2000 Server SP4 and Advanced Server SP4

oWindows Server 2003 x86/x64 R2 SP2

oWindows Server 2008 x86/x64 SP1/SP2

oWindows XP Professional SP2/SP3 and x64 SP2

oWindows Vista SP1/SP2 (except Home editions)

oWindows Seven x86/x64 (except Home editions) (Only on Hyper-V Server R2)

oSUSE Linux Enterprise Server 10 SP2 & 11

oRed Hat Enterprise Linux 5.2/5.3/5.4 x86/x64

Dell UPS Local Node Manager for Windows.

Note: Hyper-V Server doesn’t support RS232 communication port; please connect the UPS through

the USB link or through the Network link.

Dell UPS Local Node Manager

USER'S GUIDE EXTENSION FOR MICROSOFT VIRTUAL ARCHITECTURES

Dellups.com

Dell ULNM - User guide extension - HyperV R1 & R2

rev0.01

CHAPTER: Installation

2.2. MICROSOFT HYPER-V MANAGER / HYPER-V SERVER R1 & R2 CONFIGURATION

For the automatic OS boot on start-up, the user must configure the physical machine to allow

automatic OS boot on start-up. This is found in the machine’s BIOS.

For further information, see specific documentation of the physical hardware.

Note: It may be required to activate Virtualization Technology Enabled (in the machine’s BIOS) to run

Hyper-V, in CPU Information -> Virtualization Technology -> Enabled

To enable graceful virtual machines shutdown, it is necessary to install on each Virtual Machine the

additional program “Guest Component Service” included in the operating system and to configure it.

2.2.1. “GUEST COMPONENT SERVICE” INSTALLATION

Open the Hyper-V console and start your virtual machine.

Select the Action tab



insert the disk integration services.

Install the Service. To check that installation works fine, verify that the software is available

in the Control Panel of the virtual machine ("Add / Remove Programs").

2.2.2. SERVICES CONFIGURATION

Open Hyper-V console and select the virtual machine where the service was installed.

Do a Right-click. Choose Settings



Integration Services.

Check the box "Operating System shutdown".

Dell UPS Local Node Manager

USER'S GUIDE EXTENSION FOR MICROSOFT VIRTUAL ARCHITECTURES

Dellups.com

Dell ULNM - User guide extension - HyperV R1 & R2

rev0.01

CHAPTER: Installation

This configuration is illustrated on the following screenshot:

Dell UPS Local Node Manager

USER'S GUIDE EXTENSION FOR MICROSOFT VIRTUAL ARCHITECTURES

Dellups.com

Dell ULNM - User guide extension - HyperV R1 & R2

rev0.01

CHAPTER: Installation

To ensure an automatic boot of each virtual machine when Microsoft Hyper-V starts-up, use the

following procedure:

From the “Hyper-V” manager:

oSelect the virtual Machine list

oSelect the “Virtual Machine”

oSelect Parameters



Manage



Automatic Start Action

oChoose the appropriate parameters for the virtual machine that coincide with the

start rules of the specific application.

This configuration is illustrated on the following screenshot:

Dell UPS Local Node Manager

USER'S GUIDE EXTENSION FOR MICROSOFT VIRTUAL ARCHITECTURES

Dellups.com

Dell ULNM - User guide extension - HyperV R1 & R2

rev0.01

CHAPTER: Installation

Follow this procedure to ensure an automatic graceful shutdown of each virtual machine when

Microsoft Hyper-V stops:

From the “Hyper-V” manager:

oSelect the virtual Machine list,

oSelect the “Virtual Machine”

oSelect Parameters



Management



Automatic Stop Actions,

oChoose the appropriate parameters for the virtual machine, to fit with shutdown

rules of the specific application

This configuration is illustrated on the following screenshot:

Dell UPS Local Node Manager

USER'S GUIDE EXTENSION FOR MICROSOFT VIRTUAL ARCHITECTURES

Dellups.com

Dell ULNM - User guide extension - HyperV R1 & R2

rev0.01

CHAPTER: Installation

Note: With Windows Hyper-V Server, this configuration will be done remotely.

MMC Microsoft console is installed on a remote computer running Windows 2008 Server or Vista

SP1.

Dell UPS Local Node Manager

USER'S GUIDE EXTENSION FOR MICROSOFT VIRTUAL ARCHITECTURES

Dellups.com

Dell ULNM - User guide extension - HyperV R1 & R2

rev0.01

CHAPTER: Installation

2.3. DELL HARDWARE ARCHITECTURE

The prerequisites for Dell UPS Local Node Manager installation are described in the "Dell UPS Local

Node Manager –User Guide" chapter: “Installation Prerequisites“. (http://www.dellups.com/)

For UPS systems compatibility, please refer to the chapter “Appendix -> Compatibility List”

2.4. NETWORK ARCHITECTURE

All hardware elements must have an operational network configuration that allows free dialog

amongst each other.

Connections through the following ports must be authorized within the firewall of the main

operating system:

Connections on tcp port 4679 and 4680 to enable a remote access for supervision and

configuration through Web Browser. These ports are reserved at IANA

(http://www.iana.org/).

Connections through TCP port 80 must be opened as a destination port (for output) on the

machine hosting Dell UPS Local Node Manager. (To enable communication between Dell

UPS Local Node Manager and Network Management Card).

To configure network parameters of the main operating system, please refer to its user manual.

2.5. INSTALLING DELL ULNM ON HYPER-V SERVER R1 & R2 AND WINDOWS SERVER

2008 R2 (HYPER-V MANAGER)

Download the latest version of Dell UPS Local Node Manager Windows version package from

Dell’s website : http://www.dellups.com/ and choose the version windows of Dell ULNM

Copy the package on your system.

Execute the package from the DOS Windows command and Go to the directory where you

placed Dell UPS Local Node Manager.

Andere Handbücher für PowerEdge UPS 500T

Inhaltsverzeichnis

Andere Dell Server Handbücher

Dell

Dell PowerEdge XR8620t Handbuch

Dell

Dell PowerEdge 1655MC Bedienungsanleitung

Dell

Dell poweredge VRTX Bedienungsanleitung

Dell

Dell PowerEdge R210 Technisches Handbuch

Dell

Dell PowerEdge UPS 500T Bedienungsanleitung

Dell

Dell PowerEdge T630 Bedienungsanleitung

Dell

Dell PowerEdge C5125 Handbuch

Dell

Dell PowerEdge R200 Technisches Handbuch

Dell

Dell EMC PowerEdge M640 Handbuch

Dell

Dell PowerEdge C6145 Bedienungsanleitung

Dell

Dell PowerEdge R650XS M4JNT Handbuch

Dell

Dell PowerEdge 1955 Bedienungsanleitung

Dell

Dell DX6000G Bedienungsanleitung

Dell

Dell PowerEdge E31S Series Bedienungsanleitung

Dell

Dell PowerEdge R930 Bedienungsanleitung

Dell

Dell PowerEdge M1000e Bedienungsanleitung

Dell

Dell PowerEdge 2950 Technisches Handbuch

Dell

Dell 5J5D0 Handbuch

Dell

Dell Force10 C150 Bedienungsanleitung

Dell

Dell PowerEdge DR715 Bedienungsanleitung

Dell

Dell PowerEdge 1750 Handbuch

Dell

Dell PowerEdge C8000 Bedienungsanleitung

Dell

Dell PowerEdge R730 Kurzanleitung

Dell

Dell OptiPlex FX130 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung