Dell Wyse Z90D7 Bedienungsanleitung

Installation Guide

Dell® Wyse Z Class Conversion to WES7p

Wyse USB Firmware ToolTM Release 1.20.0.1

Products: Z90D7, Z90S7, Z90DE7, Z90DW, Z90SW

Issue: 021214

PN: 883887-37L Rev. A

This manual and the software and firmware described in it are copyrighted. You may not reproduce, transmit,

transcribe, store in a retrieval system, or translate into any language or computer language, in any form or by

any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, any part of this

publication without express written permission.

End User License Agreement (“License”)

A copy of the End User License Agreement is included in the software and provided for your reference only.

The License at http://www.wyse.com/license as of the purchase date is the controlling licensing agreement. By

copying, using, or installing the software or the product, you agree to be bound by those terms.

Trademarks

The Dell, Wyse, and PocketCloud logos and Wyse and PocketCloud are trademarks of Dell Inc. Other product

names mentioned herein are for identification purposes only and may be trademarks and/or registered

trademarks of their respective companies. Specifications subject to change without notice.

You acknowledge that the Software is of U.S. origin. You agree to comply with all applicable international and

national laws that apply to the Software, including the U.S. Export Administration Regulations, as well as

end-user, end-use and country destination restrictions issued by U.S. and other governments. For additional

information on exporting the Software, see http://www.microsoft.com/exporting.

Ordering Information

For availability, pricing, and ordering information in the United States and Canada, call 1-800-438-9973 or visit

us at Dell.com. In all other countries, contact your sales representative.

Contents

1 Introduction 1

Kit Contents 1

Kit Warranty 2

Overview 2

Dell Technical Support 2

Related Documentation and Services 2

Dell Online Community 2

2 Installing Z Class Flash 3

Requirements 3

Procedures 3

3 Installing WES7p Firmware 7

Requirements 7

Procedures 8

Troubleshooting 13

USB Keys - Troubleshooting Boot Issues 13

SanDisk Cruiser Flash Drives - Troubleshooting Partition Issues 13

iv Contents

This page intentionally blank.

1Introduction

This guide provides step-by-step instructions to use Wyse USB Firmware Tool to

convert the following Wyse Z class thin clients to WES7p:

•Z90D7

•Z90S7

•Z90DE7

•Z90DW

•Z90SW

CAUTION: WES7p firmware requires Z class thin clients to have a minimum of 8 GB

Flash and 4 GB RAM (16 GB Flash and 4 GB RAM is recommended).

TIP: After converting your thin clients, obtain any available firmware update at

http://www.wyse.com/serviceandsupport/support/downloads.asp.

Kit Contents

The conversion kit can include:

•Conversion Software Assembly DVD-ROM

•Flash module (16 GB)

•Wyse Conversion Labels (you must attach a Wyse label to each converted thin

client)

•Microsoft License Labels (you must attach a COA label to each converted thin client)

Figure 1 Kit contents (items may look different or not be included in your kit)

The Conversion Software Assembly DVD-ROM contains:

•A PDF of this Reference Guide

•Wyse USB Firmware Tool Release 1.20.0.1

•Z Class WES7p Conversion Image folder containing the following files:

·bios.img

·commandsXml.xml

·initrd.pxe

·Merlin.log

2Chapter 1

·mbr.img

·par1.img

·par2image1.img

·par2image2i.img

·vmlinuz

Kit Warranty

The warranty on the hardware component of this kit assumes the remaining months of

warranty of the thin client in which it is installed, or for 90 days, whichever is greater.

Installation of this kit will not void the factory warranty, however the user will be

responsible for damage due to improper installation.

Overview

To convert your Z class thin clients to WES7p:

1. (Optional) If you need to perform a hardware installation (install new flash),

complete "Installing Z Class Flash."

2. (Required) Complete "Installing WES7p Firmware."

Dell Technical Support

To access Dell technical resources, visit http://www.wyse.com/support. If you still have

questions, you can submit your questions using the Self-Service Center at

http://support.wyse.com/selfservice.html or call Customer Support at 1-800-800-9973

(toll free in U.S. and Canada). Hours of operation are from 6:00 A.M. to 5:00 P.M. Pacific

Time, Monday through Friday.

To access international support, visit http://www.wyse.com/global.

Related Documentation and Services

Fact Sheets containing the features of hardware products are available on the Dell Web

site. Go to http://www.wyse.com/products and use the Cloud clients tab to locate and

download the Fact Sheet for your hardware product.

Administrator and other documentation for your cloud client model are available at:

http://www.wyse.com/manuals.

Dell Online Community

Dell maintains an online community where users of our products can seek and

exchange information on user forums. Visit the Online Community forums at:

http://community.wyse.com/forum.

2Installing Z Class Flash

This chapter contains information for users of Wyse Z class thin clients who must

install new flash. If you are installing firmware only, you can skip this chapter and

proceed to "Installing WES7p Firmware."

Requirements

•Small Phillips screwdriver

WARNING: Flash modules may be susceptible to damage by Electro-Static Discharge

(ESD). All industry-standard cautions should be followed to avoid ESD. Before you

remove or install a module, touch any metal part of the chassis and keep that contact

with the chassis during the installation process.

Procedures

CAUTION: Follow all precautions listed in the Quick-Start Guide that came with your

thin client for disconnecting and reconnecting the thin client.

1. Perform a proper shutdown of the thin client by closing all files and ending your

session, and then pressing the power button to turn off the thin client.

2. Unplug the power cord and power adapter, and remove any other cables from the

thin client, and detach the vertical foot.

3. Position the thin client horizontally, where the side with four flat screws is facing

downward. Using the Phillips Screwdriver remove the two screws from either end

near the back panel, and then remove the three screws from the cover along the

back panel edge, as shown in Figure 2.

Figure 2 Removing the cover screws

4Chapter 2

4. Place your thumbs on the top surface above where the end screws were removed.

With a continuous motion, push firmly downward and towards the back panel

(pushing down unlatches the hooks under the cover). The cover will shift

approximate 1/4 inch to hang over the back panel, as shown in Figure 3.

Figure 3 Unlatching the cover

5. (a) Grasp the overhanging cover edge and raise the edge

about 1-1/2 inches, and then (b) pull the cover out towards the back panel at the

same angle to free the opposite end of the cover from the remaining hooks, as

shown in Figure 4.

Figure 4 Removing the cover

6. Remove the cover to expose the flash module, as shown in Figure 5.

WARNING: Flash modules may be susceptible to damage by Electro-Static

Discharge (ESD). All industry-standard cautions should be followed to avoid ESD.

Before you remove or install a module, touch any metal part of the chassis and keep

that contact with the chassis during the installation process.

Installing Z Class Flash 5

7. Remove the existing flash module. Locate the flash module and use the Phillips

Screwdriver to remove its retaining screw as shown in Figure 5. Lift the flash module

out of the socket.

Figure 5 Removing the existing flash module

8. Install the new flash module in the reverse order of removing the original flash

module. Carefully screw down its retaining screw until it is secure.

9. (a) Align the cover screw tabs with screw holes and press downward; (b) slide cover

toward the front of the thin client, as shown in Figure 6.

Figure 6 Reattaching the cover

10., Attach the screws in the reverse order as described in step 3.

11.Connect the power cord and power adapter, attach any other cables to the thin

client, and then attach the vertical foot.

CAUTION: Do not turn on the thin client. The thin client is ready to re-image,

however the flash module does not contain an operating system. Turning on power

to your thin client without firmware will display the error message “NO OPERATING

SYSTEM FOUND.”

12.Continue with "Installing WES7p Firmware."

6Chapter 2

This page intentionally blank.

Andere Handbücher für Wyse Z90D7

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dell Server Handbücher

Dell

Dell PowerEdge R730 Bedienungsanleitung

Dell

Dell Dimension 4100 Leitfaden

Dell

Dell PowerEdge FC630 Bedienungsanleitung

Dell

Dell PowerEdge 2600 Bedienungsanleitung

Dell

Dell Dimension 2200 Bedienungsanleitung

Dell

Dell PowerEdge 6850 Bedienungsanleitung

Dell

Dell PowerEdge T20 Kurzanleitung

Dell

Dell PowerEdge 6650 Bedienungsanleitung

Dell

Dell PowerEdge T420 Bedienungsanleitung

Dell

Dell PowerEdge R300 Kurzanleitung

Dell

Dell PowerEdge SC430 Betriebsanleitung

Dell

Dell PowerEdge M1000e Bedienungsanleitung

Dell

Dell PowerEdge 1850 Bedienungsanleitung

Dell

Dell PowerEdge T710 Kurzanleitung

Dell

Dell PowerEdge R520 Bedienungsanleitung

Dell

Dell DSS 2500 Bedienungsanleitung

Dell

Dell PowerEdge 6950 Bedienungsanleitung

Dell

Dell EMC PowerEdge R640 Handbuch

Dell

Dell PowerEdge R860 Handbuch

Dell

Dell PowerEdge 6850 Technisches Handbuch

Dell

Dell PowerEdge C8000 Bedienungsanleitung

Dell

Dell EMC PowerEdge R750xs Handbuch

Dell

Dell PowerEdge T320 Bedienungsanleitung

Dell

Dell EMC VxRack FLEX Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung