Delta MessageMaxx DMS-279 Handbuch
01992 523523
www.deltamembranes.com
MessageMaxx™ (DMS-279)
Installation & Operating Instructions Rev 1
For Ground & Foul Water
Pump Station Telemetry System
T.
E.
W.
MessageMaxx
MM-M-V1-02.16
Legal information/Copyright
All rights reserved. Contents provided herein must neither be distributed, copied, reproduced, edited or
processed for any other purpose, nor otherwise transmitted, published or made available to a third party
without express written consent from Delta Membranes.
Subject to technical modication without prior notice.
© Delta Membranes 2016
MessageMaxx
For technical support, please call 01279 757400 3
Contents
1.0 MessageMaxx overview 4
2.0 Box contents 4
2.1 Cardboard box contents 4
2.2 MessageMaxx unit contents 4
3.0 Technical information 5
4.0 Unit location 5
5.0 SIM card selection 5
6.0 Mounting the MessageMaxx unit 5
7.0 Installing the MessageMaxx unit 6
8.0 Wiring the MessageMaxx unit 7
9.0 Installing the GSM aerial 8
10.0 Conguring the MessageMaxx unit 9
11.0 Mounting the GSM aerial 9
12.0 Text commands 10
13.0 Text message structure 11
14.0 Limitations 12
15.0 Servicing 12
16.0 Spares 13
17.0 LED codes 14
1.0 MessageMaxx overview
2.0 Box contents
4 For technical support, please call 01279 757400
MessageMaxx
2.1 Cardboard box contents
• 1 x Large Cable Gland
• 1 x Large Blanking Plug
• 1 x Small Cable Gland
• 1 x Small Blanking Plug
2.2 MessageMaxx unit contents
• 1 x MessageMaxx Unit
• 1 x Chamber Location Sticker Sheet (For MessageMaxx)
• 1 x 3m length of MaxxConnect family cable
• 1 x GSM Aerial
• 1 x Aerial Mounting Plate
• 1 x Installation & Operating Instructions (this document)
This telemetry system is designed to be used in conjunction with the AlertMaxx high level alarm and has the
ability to connect with the PowerMaxx battery backup, to give remote monitoring of a pump station when
the home owner is away from their property. Messages are sent to predetermined phone numbers using
GSM technology and are received in text format.
CAUTION!
The MessageMaxx should be installed by a qualied tradesperson.
MessageMaxx
For technical support, please call 01279 757400 5
3.0 Technical information
MessageMaxx Specication
Size (without cable glands) W: 115mm x D: 95mm x H: 60mm
Weight 400g
Visual Display Red, Blue, Green LED
Operating temperature 5-35°C
Approximate Installation time 30 minutes
4.0 Unit location
The MessageMaxx must be positioned within 20m of the AlertMaxx unit it will be used in conjunction with,
somewhere with a good GSM signal, within 3m of the aerial mounting point and be permanently accessible.
MaxxConnect cable can be purchased per 10m (DMS-288). Do not join cables. Run full lengths only.
6.0 Mounting the MessageMaxx unit
1. Using the template provided on page 15 of this instruction manual (gure 1), mark the xing
positions on the wall.
2. Drill the two holes and t suitable wall plugs (ensure correct wall plugs are used for the wall type).
3. Remove the screws from the front of the unit that secure the front fascia and remove the black GSM unit
from the Velcro holding it within the casing.
4. Secure the MessageMaxx unit to the wall using appropriate screws.
PLEASE NOTE
When securing the unit to the wall, avoid over tightening the screws as this may cause the box to crack.
5.0 SIM card selection
1. Purchase a functioning traditional contract SIM card. This doesn’t require a minutes or data allowance,
just be enabled to send text messages. The SIM card must have no pin number assigned to it.
2. If possible, test the SIM card in an unblocked telephone on site and survey the area for the best signal
strength for aerial placement.
3. Once an area of installation for the aerial has been chosen, proceed as below.
CAUTION!
The MessageMaxx unit is not waterproof and must be installed indoors or inside a kiosk.
7.0 Installing the MessageMaxx unit
6 For technical support, please call 01279 757400
MessageMaxx
1. Disconnect the battery and mains power to the AlertMaxx unit and ensure the PowerMaxx is switched
o (if installed).
2. Remove the black sliding cover on the GSM box, slide the SIM hatch back, ip up, install the SIM card,
push down and lock shut. Replace the black cover.
3. Install the supplied large cable gland into the far right hand hole and a small cable gland into the far left
hand hole of the casing. Use the supplied blanking plugs to ll the remaining holes.
4. Feed the plug of the aerial through the large cable gland, screw into the silver socket on the
GSM unit and tighten the cable gland (see gure 2).
5. Push and x the GSM box on to the Velcro within the casing until a audible click is heard.
6. Feed the MaxxConnect family cable through the small cable gland and leave loose until wired in.
7. Strip the end of the MaxxConnect family cable to reveal the coloured wires.
Figure 2. Internal casing view
GSM Box
MessageMaxx
For technical support, please call 01279 757400 7
8.0 Wiring the MessageMaxx unit
Please refer to the MaxxConnect Installation & Operating Instructions.
8 For technical support, please call 01279 757400
MessageMaxx
9.0 Installing the GSM aerial
1. Prior to testing, position the aerial in the preferred mounting location - do not x. The aerial is magnetic
and should be stuck to the mounting plate (provided). This has been designed to boost the signal.
2. Set the internal switch on the PCB to the ‘SIG’ position (see gure 3).
3. The LED’s will illuminate as below.
Red LED Blue LED Green LED Signal Strength
Solid Quick ash Very strong
Solid Medium ash Sucient
Solid Slow ash Weak
Solid No ash 0%
4. If a sucient signal strength isn’t achieved, move the aerial and run the test again.
5. When complete, set the internal switch on the PCB to the ‘RUN’ position and ret the front fascia.
Figure 3. Conguring the PCB on the lid
SIG PCRUN
10.0 Conguring the MessageMaxx unit
MessageMaxx
For technical support, please call 01279 757400 9
11.0 Mounting the GSM aerial
1. Using a mobile phone, text the units telephone number with a ‘?’.
2. The green LED will ash 4/sec as the response message is sent to your mobile phone. The reply from
the unit will give you a STATUS message.
3. Ensure that all people who would like to be on the active list text the units telephone number with a ‘?’.
PLEASE NOTE
The active telephone list can store a maximum of ve numbers.
4. If you would like your telephone number removed from the MessageMaxx, text the unit with a ‘R’.
An aerial mounting plate has been provided which should be xed in your chosen location after testing the
GSM signal (see section 8.0).
1. Select the correct installation method for your chosen application using the gures below (4 & 5).
2. Using the two holes on the plate, mark the xing positions on the wall.
3. Drill the two holes and t suitable wall plugs (ensure correct wall plugs are used for the wall type).
4. Secure the mounting plate to the wall using appropriate screws.
5. Attach the magnetic aerial as pictured below.
Figure 5. Inside installationFigure 4. Outside installation
12.0 Text commands
10 For technical support, please call 01279 757400
MessageMaxx
The MessageMaxx can be interrogated using a number of dierent text message commands. The table
below shows those that can be used.
PLEASE NOTE
To be able to execute these commands, you must already be on the active telephone list.
In order to do this, text the units telephone number with a ‘?’
Command Description
? Status - This command gives an overall status of the system. It also adds your
telephone number to the active list.
L Log - This command sends the last 8 log entries held on the AlertMaxx. This log is
consolidated from all the units installed in the Maxx Family.
R Remove - This command removes your telephone number from the active list.
RA=IDIDID* Remove all - This command removes all telephone numbers from the active list.
‘IDIDID’ is the MessageMaxx ID.
AT=+44 Add telephone - This command adds a telephone number to the active list.
SP= Set property - This command will set the property name related to the MessageMaxx.
This is limited to 10 characters and will be displayed on messages from the unit.
PLEASE NOTE
*The MessageMaxx ID can be found on the white label located on the bottom right side of the unit.
The command letter must be in the rst position on the text message - no other characters are permitted.
Inhaltsverzeichnis
Andere Delta Messgerät Handbücher
Delta
Delta DPM-C510 Bedienungsanleitung
Delta
Delta DPM-C501L Bedienungsanleitung
Delta
Delta REVEZ-HD-TRIO DVB-T/T2 Bedienungsanleitung
Delta
Delta LTL-X Mark II Bedienungsanleitung
Delta
Delta WS-6975 Bedienungsanleitung
Delta
Delta XVR5432L-I2 Bedienungsanleitung
Delta
Delta UNOnext Bedienungsanleitung
Delta
Delta HD2105.2 Bedienungsanleitung
Delta
Delta dvp04pt-s Bedienungsanleitung
Delta
Delta DPM-MA1121 Bedienungsanleitung
Delta
Delta DVP04TC-H2 Bedienungsanleitung
Delta
Delta RetroSign GR1 Bedienungsanleitung
Delta
Delta OR-AE-1306 Bedienungsanleitung
Delta
Delta LTL-XL Bedienungsanleitung
Delta
Delta HD2114.0 Bedienungsanleitung
Delta
Delta DPM-C530 Bedienungsanleitung
Delta
Delta DPM-C520 Bedienungsanleitung
Delta
Delta DVP08NTC-S Bedienungsanleitung
Delta
Delta ZS1000-A-V2 Bedienungsanleitung
Delta
Delta TZU-22 Bedienungsanleitung
