Delta CliQ II DRP024V480W3B Series Bedienungsanleitung

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

24V 480W 3

Phase

/ DRP024V480W3B

□

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

www.DeltaPSU.com (December 2018, Rev. 03)

Highlights & Features

•Universal AC input voltage: 3 x 320Vac – 600Vac (3-Phase)

or 2 x 360Vac – 600Vac (2-Phase)

•Power will not de-rate for the entire input voltage range

•Power Boost of 150% for 5 seconds and 200% for 2 seconds

•Full corrosion resistant aluminium chassis

•Conformal coating on PCBA to protect against chemical and

dust pollutants

•Hazardous Locations approval to ATEX and Class I, Div 2

(DRP024V480W3BA)

Safety Standards

CB Certified for worldwide use

Model Number: DRP024V480W3B☐

Unit Weight:1.35 kg (2.98 lb)

Dimensions (L x W x D): 121 x 140 x 117.3 mm

(4.76 x 5.51 x 4.62 inch)

General Description

The CliQ II 3-phase DIN rail power supply series offers output voltage of 24V. These products are encased in rugged yet lightweight full

aluminium body that can withstand shock and vibration according to IEC 60068-2 standard. The series of 3-phase products can

operate over a wide temperature range of -25°C to +80°C. These products also feature universal AC input voltage range for 3-phase

from 320Vac to 600Vac or 2-phase from 360Vac to 600Vac, and the power will not de-rate throughout the entire range. Another great

feature is the conformal coating on the PCBA which allows selected models to be certified to ATEX and Class I, Div 2 for use in

hazardous locations. The design conforms to harmonic current emission IEC/EN 61000-3-2, Class A.

Model Information

CliQ II DIN Rail Power Supply

Model

Number

Input Voltage Range Rated Output

oltage

Rated Output Curr

ent

DRP024V480W3B☐ 3 x 320-600Vac (3-Phase) or

2 x 360-600Vac (2-Phase)

24Vdc 20.0A

Model Numbering

DR P024V

480W

□

DIN Rail Power Supply Output Voltage Output Power Three Phase CliQ II Series A - Metal Case,

with Class I, Div 2

N - Metal Case,

without Class I, Div 2

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

24V 480W 3

Phase

/ DRP024V480W3B

□

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

www.DeltaPSU.com (December 2018, Rev. 03)

Specifications

Input Ratings / Characteristics

Nominal Input Voltage 3 x 400-500Vac

Input Voltage Range 3 x 320-600Vac (3-Phase) or 2 x 360-600Vac (2-Phase)

Nominal Input Frequency 50-60Hz

Input Frequency Range 47-63Hz

DC Input Voltage Range* 450-800Vdc

Input Current < 1.00A @ 3 x 400Vac, < 0.75A @ 3 x 500Vac

Efficiency at 100% Load > 91.0% @ 3 x 400Vac & 3 x 500Vac

Max Inrush Current (Cold Start) < 50A @ 3 x 400Vac & 3 x 500Vac

Power Factor at 100% Load > 0.95 @ 3 x 400Vac, > 0.94 @ 3 x 500Vac

Leakage Current < 3.5mA @ 500Vac

*Safety approval according to IEC/EN/UL 60950-1.

Output Ratings / Characteristics

Nominal Output Voltage 24Vdc

Factory Set Point Tolerance ± 2% (initial set point tolerance from factory)

Output Voltage Adjustment Range 24-28Vdc

Output Current 20.0A (continuously operating at 24V)

30.0A (Power Boost for 5 seconds at 24V, refer to the details in

the Functions section)

40.0A (Power Boost for 2 seconds at 24V, refer to the details in

the Functions section)

Output Power 480W (continuously operating at 24V)

720W (Power Boost for 5 seconds at 24V, refer to the details in

the Functions section)

960W (Power

Boost for 2 seconds at 24V, refer to the details in

the Functions section)

Line Regulation < 0.5% typ. (@ 3 x 320-600Vac input, 100% load)

Load Regulation < 1% typ. (@ 3 x 320-600Vac input, 0-100% load)

PARD (20MHz) < 150mVpp

Rise Time

< 100ms @ nominal input (100% load)

Start-up Time < 1,000ms @ nominal input (100% load)

Hold-up Time > 20ms @ 3 x 400Vac & 3 x 500Vac (100% load)

Dynamic Response (Overshoot & Undershoot O/P Voltage) ± 5% @ 10-90% load

Start-up with Capacitive Loads 10,000µF Max

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

24V 480W 3

Phase

/ DRP024V480W3B

□

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

www.DeltaPSU.com (December 2018, Rev. 03)

Mechanical

Case Cover / Chassis

Aluminium

Dimensions (L x W x D) 121 x 140 x 117.3 mm (4.76 x 5.51 x 4.62 inch)

Unit Weight 1.35 kg (2.98 lb)

Indicator Green LED (DC OK)

Cooling System Convection

Terminal Input 4 Pins (Rated 600V/35A)

Output 4 Pins (Rated 300V/30A)

Wire Input AWG 18-8

Output AWG 12-10

Mounting Rail Standard TS35 DIN Rail in accordance with EN 60715

Noise (1 Meter from power supply) Sound Pressure Level (SPL) < 40dBA

Environment

Surrounding Air Temperature Operating -25°C to +80°C (Cold Start at -40°C)

Storage -40°C to +85°C

Power De-rating Vertical Mounting > 50°C de-rate power by 2.5% / °C,

> 70°C de-rate power by 5% / °C

Operating Humidity 5 to 95% RH (Non-Condensing)

Operating Altitude 0 to 2,500 Meters (8,200 ft.) for ITE application (@ 50°C)

0 to 2,000 Meters (6,560 ft.) for Industrial application (@ 50°C)

Shock Test Non-Operating IEC 60068-2-27, 30G (300m/S²) for a duration of 18ms,

1 time per direction, 2 times in total

Vibration Non-Operating IEC 60068-2-6, 10Hz to 500Hz @ 30m/S² (3G peak);

60 min per axis for all X, Y, Z direction

Pollution Degree 2

Protections

Overvoltage 32V ±10%, SELV Output, Hiccup Mode,

Non-Latching (Auto-Recovery)

Overload / Overcurrent > 200% of rated load current, Hiccup Mode,

Non-Latching (Auto-Recovery)

Over Temperature < 80°C Surrounding Air Temperature @ 100% load,

Non-Latching (Auto-Recovery)

Short Circuit Hiccup Mode, Non-Latching

(Auto-Recovery when the fault is removed)

Degree of Protection IP20

Protection Against Shock Class I with PE* connection

*PE: Primary Earth

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

24V 480W 3

Phase

/ DRP024V480W3B

□

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

www.DeltaPSU.com (December 2018, Rev. 03)

Reliability Data

MTBF > 500,000 hrs. as per Telcordia SR-332

I/P: 3 x 400Vac, O/P: 100% load, Ta: 25°C

Expected Cap Life Time 10 years (3 x 400Vac & 3x 500Vac, 50% load @ 40°C)

Safety Standards / Directives

Electrical Equipment in Power

Installations

EN 50178 / IEC 62103

Electrical Safety SIQ Bauart

EN 60950-1

UL/cUL recognized UL 60950-1 and CSA C22.2 No. 60950-1 (File No. E191395)

CB scheme IEC 60950-1

Industrial Control Equipment UL/cUL listed UL 508 and CSA C22.2 No. 107.1-01 (File No. E315355)

CSA CSA C22.2 No. 107.1-01 (File No. 181564)

Hazardous Location / ATEX cCSAus CSA C22.2 No. 213-M1987, ANSI / ISA 12.12.01:2007

[Class I, Division 2, Group A, B, C, D T4, Ta = -25°C to +80°C

(> +50°C derating)]

ATEX EN 60079-0:2012, EN 60079-15:2010

[ II 3G Ex nA IIC T4 Gc, Ta= -25°C to +80°C (> +50°C

derating)]

Certificate No. EPS 13 ATEX 1 575 X

CE In conformance with EMC Directive 2014/30/EU and

Low Voltage Directive 2014/35/EU

DRP024V480W3BA:

In conformance with Equipment for explosive atmospheres

(ATEX) directive 2014/34/EU

Material and Parts RoHS Directive 2011/65/EU Compliant

Galvanic Isolation Input to Output 4.0KVac

Input to Ground 2.0KVac

Output to Ground 1.5KVac

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

24V 480W 3

Phase

/ DRP024V480W3B

□

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

www.DeltaPSU.com (December 2018, Rev. 03)

EMC

Emissions (CE & RE) CISPR 32, EN 55032, CISPR 11, EN 55011,

FCC Title 47: Class B

Component Power Supply for General Use

EN 61204-3

Immunity EN 55024, EN 61000-6-2

Electrostatic Discharge IEC 61000-4-2 Level 4 Criteria A1)

Air Discharge: 15kV

Contact Discharge: 8kV

Radiated Field IEC 61000-4-3 Level 3 Criteria A1)

80MHz-1GHz, 10V/M, 80% modulation (1KHz)

1.4GHz-2GHz, 3V/M, 80% modulation (1KHz)

2GHz-2.7GHz, 1V/M, 80% modulation (1KHz)

Electrical Fast Transient / Burst IEC 61000-4-4 Level 3 Criteria A1)

2kV

Surge IEC 61000-4-5 Level 3 Criteria A1)

Common Mode2): 2kV

Differential Mode3): 1kV

Conducted IEC 61000-4-6 Level 3 Criteria A1)

150kHz-80MHz, 10Vrms

Power Frequency Magnetic Fields IEC 61000-4-8 Criteria A1)

30A/Meter

Voltage Dips IEC 61000-4-11 100% dip; 1 cycle (20ms); Self Recoverable

Low Energy Pulse Test (Ring Wave) IEC 61000-4-12 Level 3 Criteria A1)

Common Mode2): 2kV

Differential Mode3): 1kV

Harmonic Current Emission IEC/EN 61000-3-2, Class A

Voltage Fluctuation and Flicker IEC/EN 61000-3-3

1) Criteria A: Normal performance within the specification limits

2) Asymmetrical: Common mode (Line to earth)

3) Symmetrical: Differential mode (Line to line)

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

24V 480W 3

Phase

/ DRP024V480W3B

□

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

www.DeltaPSU.com (December 2018, Rev. 03)

Block Diagram

Device Description

1) Input terminal block connector

2) Output terminal block connector

3) DC Voltage adjustment potentiometer

4) DC OK control LED (Green)

5) Universal mounting rail system

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

24V 480W 3

Phase

/ DRP024V480W3B

□

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

www.DeltaPSU.com (December 2018, Rev. 03)

Dimensions

L x W x D: 121 x 140 x 117.3 mm (4.76 x 5.51 x 4.62 inch)

Engineering Data

Output Load De-rating VS Surrounding Air Temperature

Note

1. Power supply components may degrade, or

be damaged, when the power supply is

continuously used outside the shaded region,

refer to the graph shown in Fig. 1.

2. If the output capacity is not reduced when the

surrounding air temperature >50°C (Vertical),

the device may run into Over Temperature

Protection. When activated, the output

voltage will go into bouncing mode and will

recover when the surrounding air

temperature is lowered or the load is reduced

as far as necessary to keep the device in

working condition.

3. In order for the device to function in the

manner intended, it is also necessary to keep

a safety distance of 5mm (0.20 inch) for

Vertical Mounting with adjacent units while

the device is in operation.

Depending on the surrounding air

temperature and output load delivered by the

power supply, the device can be very hot!

5. If the device has to be mounted in any other

orientation, please contact

[email protected]om for more details.

Fig. 1 De-rating for Vertical Mounting Orientation

> 50°C de-rate power by 2.5% / °C,

> 70°C de-rate power by 5% / °C

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

24V 480W 3

Phase

/ DRP024V480W3B

□

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

www.DeltaPSU.com (December 2018, Rev. 03)

Output Load De-rating VS Input Voltage

Assembly & Installation

The power supply unit (PSU) can be mounted on 35mm DIN rails in accordance with EN 60715. For Vertical Mounting, the device

should be installed with input terminal block at the bottom.

Each device is delivered ready to install.

Mounting

No output power de-rating across the entire

input voltage range 3 x 320-600Vac

(3-Phase) or 2 x 360-600Vac (2-Phase)

Dismounting

Fig. 2.1 Mounting

Snap on the DIN rail as shown in Fig. 2.1:

1. Tilt the unit upwards and insert it onto the DIN rail.

2. Push downwards until stopped.

3. Press against the bottom front side for locking.

4. Shake the unit slightly to ensure that it is secured.

Fig. 2.2 Dismounting

To uninstall, pull or slide down the latch with screw driver as

shown in Fig. 2.2. Then slide the power supply unit (PSU) in

the opposite direction, release the latch and pull out the power

supply unit (PSU) from the rail.

In accordance to EN 60950 / UL 50950, flexible cables require ferrules.

Use appropriate copper cables designed to sustain operating temperature of:

1. 60°C, 60°C / 75°C for USA

2. At least 75°C for ambient not exceeding 50°C, and 90°C for ambient exceeding 50°C for Canada.

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

24V 480W 3

Phase

/ DRP024V480W3B

□

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

www.DeltaPSU.com (December 2018, Rev. 03)

Safety Instructions

Vertical Mounting

•ALWAYS switch mains of input power OFF before connecting and disconnecting the input voltage to the unit. If mains are not

turned OFF, there is risk of explosion / severe damage.

•To guarantee sufficient convection cooling, keep a distance of 50mm (1.97 inch) above and below the device as well as a

lateral distance of 5mm (0.20 inch) to other units.

•Note that the enclosure of the device can become very hot depending on the surrounding air temperature and load of the power

supply. Risk of burns!

•Only plug in and unplug connectors when power is turned off!

•DO NOT insert any objects into the unit.

•Hazardous voltages may be present for up to 5 minutes after the input mains voltage is disconnected. Do not touch the unit during

this time.

•The power supplies unit should be installed in minimum IP54 rated enclosure.

•The power supplies are built in units and must be installed in a cabinet or room (condensation free environment and indoor

location) that is relatively free of conductive contaminants.

•CAUTION: “For use in a controlled environment”.

•It is NOT advised to install in horizontal mounting orientation, since it may cause damage to the PSU.

For DRP024V480W3BA:

•The power supplies unit must be installed in an IP54 enclosure or cabinet in the final installation. The enclosure or cabinet must

comply with EN60079-0 or EN60079-15.

•Warning: Explosion Hazard - Substitution of components may impair suitability for Class I, Division 2.

•Warning: Explosion Hazard - Do not disconnect equipment or adjust potentiometer unless the power has been switched off or the

area is known to be non-hazardous.

TECHNICAL DATASHEET

CliQ II DIN Rail Power

Supply

24V 480W 3

Phase

/ DRP024V480W3B

□

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

www.DeltaPSU.com (December 2018, Rev. 03)

Functions

Graph illustrating the Start-up Time, Rise Time, and Hold-up Time

Start-up Time

The time required for the output voltage to reach 90% of its final steady state set value, after the input voltage is applied.

Rise Time

The time required for the output voltage to change from 10% to 90% of its final steady state set value.

Hold-up Time

Time between the collapse of the AC input voltage, and the output falling to 95% of its steady state set value.

Inrush Current

Inrush current is the peak, instantaneous, input current measured

and, occurs when the input voltage is first applied. For AC input

voltages, the maximum peak value of inrush current will occur

during the first half cycle of the applied AC voltage. This peak

value decreases exponentially during subsequent cycles of AC

voltage.

Dynamic Response

The power supply output voltage will remains within ±5% of its

steady state value, when subjected to a dynamic load from 10%

to 90% of its rated current.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Delta Stromversorgung Handbücher

Delta

Delta PMT Series Bedienungsanleitung

Delta

Delta PMT-24V350W1AK Bedienungsanleitung

Delta

Delta PMC Series Bedienungsanleitung

Delta

Delta PM 24V200W1AI Series Bedienungsanleitung

Delta

Delta PMC-24V150W1AA Bedienungsanleitung

Delta

Delta PMC-24V075W1AA Bedienungsanleitung

Delta

Delta DNPS01 Bedienungsanleitung

Delta

Delta PMT2 75 W Series Bedienungsanleitung

Delta

Delta PMC-12V035W1AA Bedienungsanleitung

Delta

Delta Sync DRS-12V50W1N Series Bedienungsanleitung

Delta

Delta IMA-1000 Series Montage- und Bedienungsanleitung

Delta

Delta 24V/8A/PA18AC Bedienungsanleitung

Delta

Delta DRP024V240W3BA Kurzanleitung

Delta

Delta PMT Series Bedienungsanleitung

Delta

Delta PMT-4V350W1A Series Bedienungsanleitung

Delta

Delta LYTE II Bedienungsanleitung

Delta

Delta PMC-24V100W1AA Bedienungsanleitung

Delta

Delta DVPPS01 Bedienungsanleitung

Delta

Delta PMC-24V100W1AA Bedienungsanleitung

Delta

Delta LYTE II Bedienungsanleitung

Delta

Delta MCS-600 Series Gebrauchsanweisung

Delta

Delta PMC-05V050W1AA Bedienungsanleitung

Delta

Delta DRP024V480W1AA Bedienungsanleitung

Delta

Delta PMC-12V100W1AA Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung