Desa GA9150A Bedienungsanleitung

WARNING: If the information in this manual is not





-



     -

       

-



   



The GA9150A Series Remote Ready On/Off Safety Valve/Pilot kit contains the following:

• Piezo Ignitor 097159-04

• MV Valve 14512

• Propane/LP Conversion Regulator 106380-01

• Pilot Burner

(with natural gas orice) 901073-01

• Piezo Ignitor Electrode 901072-01

• Steel Shroud - Pilot Kit 106823-01

• Piezo Ignitor Cover 106824-01

• Natural Gas Brass Orice 901064-03

• Natural Gas Brass Orice 901064-04

• Natural Gas Brass Orice 901064-09

GA9150A REMOTE-READY VALVE/PILOT kit

INSTRUCTION MANUAL

Save this manual for future reference.

For more information, visit www.desatech.com

• Brass Flare Adaptor Fitting 901056-01

• Propane/LP Conversion Decal 901691-01

• Screw #10-32 x 1/4" 11107

• 18" Propane/LP Brass Orice 901065-02

• 24" Propane/LP Brass Orice 901065-03

• 30" Propane/LP Brass Orice 901065-04

• Propane/LP Brass Air Mixer 901066-02

• Propane/LP Pilot Burner Orice 901070-01

• Screws 1/4" #8 “B” pt (6 ea.) 901075-01

• Refractory Remote Control 901837-01

• 4" Jumper Wire 14580

      



For All Single, Dual and Triple Burner

Natural and Propane/LP Gas Logs

www.desatech.com 901053-01J2

INSTALLATION

  

MODEL DESCRIPTION   

CVSR18 18" Single Burner 50,000 40,000 8" dia.

CPVSR18 18" Single Burner 50,000 40,000 8" dia.

CVSR24 24" Single Burner 60,000 50,000 8" dia.

CPVSR24 24" Single Burner 60,000 50,000 8" dia.

CVDR18 18" Dual Burner 55,000 45,000 8" dia.

MD18 18" Dual Burner 55,000 45,000 8" dia.

CVDR24 24" Dual Burner 65,000 55,000 8" dia.

MD24 24" Dual Burner 65,000 55,000 8" dia.

CVDR30 30" Dual Burner 70,000 60,000 8" dia.

(C)BFL(T,R) 18" Triple Burner 65,000 55,000 8" dia.

(C)BFL(T,R) 24" Triple Burner 70,000 60,000 8" dia.

  

 

Inlet Manifold*

NG 5.5"-10.5" 3.5"

LP 11"-13" 10"

* ± .2"

CHECK GAS TYPE

You must install this Remote Ready Valve/

Pilot Kit if your gas type is propane/LP. For ad-

ditional convenience and safety, this Remote

Ready Valve/Pilot Kit can be used with natural

gas. If you are unsure of the proper applica-

tion, call dealer where you bought log set.

If the replace does not have a gas supply

shutoff valve, one must be installed.

CONNECTING TO GAS SUPPLY

   

    





Figure 1 - Technical Information Charts



  

MODEL WIDTH* WIDTH** DEPTH HEIGHT

18DR/SR/MD 28" 16" 14" 18"

24DR/SR/MD 29 3/4" 17" 15 1/2" 18"

30DR 36" 27" 18" 18"

BFL18 28" 16" 15 1/2" 18"

BFL24 30" 22" 15 1/2" 18"

* Add 6" if valve/pilot is used

**At depth indicated



NATURAL PROPANE/LP

LOG       

18SR/DR/MD 0.129 30 Green 0.073 49 Red

24SR/DR/MD/BFL18 0.141 28 Yellow 0.086 44 Orange

30DR/BFL24 0.157 22 Yellow/ 0.089 43 Black

Blue







-





   







www.desatech.com 3901053-01J

Installation Items Needed

Before installing log set, make sure you have

the items listed below.

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve*

• test gauge connection*

• adjustable (crescent) wrench or pliers

• sediment trap

• tee joint

• pipe wrench

• exible gas line

* A CSA design-certied equipment shutoff

valve with 1/8" NPT tap is an acceptable al-

ternative to test gauge connection. Purchase

the optional CSA design-certied equipment

shutoff valve from your dealer.

For propane/LP units, the installer must

supply an external regulator. The external

regulator will reduce incoming gas pressure.

You must reduce incoming gas pressure

to between 11" and 14" of water. If you do

not reduce incoming gas pressure, heater

regulator damage could occur. Install exter-

nal regulator with the vent pointing down as

shown in Figure 2, page 3. Pointing the vent

down protects it from freezing rain or sleet.

WARNING: Never connect



   

    



CAUTION: Use only new,

     -





     









INSTALLATION

Continued

Installation must include an equipment shutoff

valve, union and plugged 1/8" NPT tap. Locate

NPT tap within reach for test gauge hook up.

NPT tap must be upstream from log set (see

Figure 3, page 4).

IMPORTANT: Install equipment shutoff valve

in an accessible location. The equipment

shutoff valve is for turning on or shutting off

the gas to the appliance.

Check your building codes for any special

requirements for locating equipment shutoff

valve to appliance.

Apply pipe joint sealant lightly to male NPT

threads. This will prevent excess sealant from

going into pipe. Excess sealant in pipe could

result in a clogged burner orice.

    





We recommend that you install a sediment

trap in supply line as shown in Figure 3,

page 4. Locate sediment trap where it is

within reach for cleaning. Install in piping

system between fuel supply and heater.

Locate sediment trap where trapped matter

is not likely to freeze. A sediment trap traps

moisture and contaminants. This keeps

them from going into log set controls. If

sediment trap is not installed or is installed

wrong, log set may not run properly.

Figure 2 - External Regulator on

Propane/LP Supply Tank with Vent

Pointing Down

External

Regulator

Vent

Pointing

Down

Propane/LP

Supply Tank

www.desatech.com 901053-01J4

INSTALLATION

Continued

Figure 4 - Equipment Shutoff Valve

Open

Closed

Equipment

Shutoff Valve

CHECKING GAS CONNECTIONS



and connections, internal and



 



WARNING: Never use an



-









    

   





PRESSURE TESTING GAS SUPPLY

PIPING SYSTEM





1. Disconnect log set and its individual

equipment shutoff valve from gas supply

piping system.

2. Cap off open end of gas pipe where equip-

ment shutoff valve was connected.

3. Pressurize supply piping system by either

opening propane/LP supply tank valve

for propane/LP gas or opening main gas

valve located on or near gas meter for

natural gas, or using compressed air.

4. Check all joints of gas supply piping sys-

tem. Apply noncorrosive leak detection

uid to all joints. Bubbles forming show a

leak.

5. Correct all leaks at once.

6. Reconnect log set and equipment shutoff

valve to gas supply. Check reconnected

ttings for leaks.





1. Close equipment shutoff valve (see

Figure 4).

2. Pressurize supply piping system by either

opening propane/LP supply tank valve

for propane/LP gas or opening main gas

valve located on or near gas meter for

natural gas, or using compressed air.

3. Check all joints from gas meter for natural

gas (see Figure 5, page 5) or propane/LP

supply (see Figure 6, page 5) to equip-

ment shutoff valve. Apply noncorrosive

leak detection uid to all joints. Bubbles

forming show a leak.

4. Correct all leaks at once.

Tee Pipe Cap

Joint Nipple

Approved Flexible

Gas Hose (if allowed

by local codes)

Figure 3 - Gas Connection

* Purchase the optional CSA design-certied

equipment shutoff valve from your dealer.

** Minimum inlet pressure for purpose of input

adjustment.

3" Minimum

Sediment Trap

CSA Design-Certied

Equipment Shutoff Valve

With 1/8" NPT Tap*

Natural Gas

From Gas Meter

(5" W.C.** to 10.5"

W.C. Pressure)



From External

Regulator

(11" W.C.**

to 14" W.C.

Pressure)

www.desatech.com 5901053-01J

Figure 6 - Checking Gas Joints (Propane/

LP Gas Only)

Figure 5 - Checking Gas Joints

Gas Meter

Equipment

Shutoff Valve

INSTALLATION

Continued

Equipment

Shutoff Valve

Propane/LP

Supply Tank

6. Install the inlet tting into the inlet opening

of the gas control valve (see Figure 9). Use

thread sealant on the male pipe threads.

7. Place the burner pan assembly in the

center of the replace oor. Make sure

the front of pan faces forward.

Figure 8 - Gas Control Valve with

Thermocouple and Pilot (Valve May Vary

from Illustration)

Thermopile and Line

Pilot and Line

Gas

Control

Valve

Pressure Tap -

Out (Manifold) Pressure Tap - In

(Inlet)



PILOT KIT ASSEMbLY

Natural Gas Installation

1. Remove burner inlet tting from burner

manifold (see Figure 7).

2. Use 10 mm socket to remove the orice

(see Figure 11, page 6). Replace with the

proper orice for your log set. See technical

information charts in Figure 1 on page 2.

3. Thread the gas control valve onto the

burner inlet tting (see Figure 7). Use

thread sealant on the male threads of the

burner inlet tting. Hold the burner inlet

tting with a wrench to prevent overtight-

ening the connection to the burner. Make

sure the control knob is facing the front

(see Figure 7).

4. Replace burner inlet tting into burner

manifold (see Figure 7).

5. Attach the pilot gas line to the pilot outlet of

the gas control valve and tighten. Connect

thermocouple wires to TP and TPTH termi-

nals on gas valve terminal block. See Figure

8. Do not overtighten. If using propane/LP

gas, see Changing Pilot Orice, page 7.

Burner Inlet Fitting

(containing orice)

Gas

Control

Valve

Burner Pan

Assembly

Figure 7 - Installing Gas Control Valve

(Valve May Vary from Illustration)

Control Knob

Figure 9 - Installing Inlet Fitting and Gas

Connector Tube (Valve May Vary from

Illustration)

Gas

Control

Valve Gas Inlet Fitting

Gas

Connector

Tube

Inlet

Opening

www.desatech.com 901053-01J6

INSTALLATION

Continued

8. Thread the gas supply adaptor to the

replace gas supply pipe. Adjust to most

convenient position.

9. Install the gas connector tube to the gas

supply adapter. Carefully shape tube and

attach to gas inlet tting (see Figure 9,

page 5). Be careful not to cause kinks in

tube.

10. Test for leaks following instructions in your

hearth kit owner’s manual under the sec-

tion Testing Burner for Leaks.

11. Retighten and adjust the location of the

gas control as necessary. The gas control

should be level, with the control knob to

the front.

12. Install cover to burner pan using screws

provided.

13. Install thermocouple, pilot, and piezo

ignitor cover onto valve cover as shown

in Figure 10. Use the provided screws.

Piezo Ignitor

Screw

Valve

Cover

Figure 10 - Installing Thermocouple,

Pilot, and Piezo Ignitor Cover (Valve May

Vary from Illustration)

Thermopile

Ignitor

Pilot

Piezo

Ignitor

Cover

Machine

Screw

Figure 11 - Burner Inlet Fittings with

Injectors

NATURAL

GAS

FITTING

PROPANE/LP

GAS FITTING

Injector for

Natural Gas

Injector for

Propane/LP Gas

WARNING: You must use a





Figure 12 - Remove Burner Inlet Fitting

Burner Inlet

Fitting for

Natural Gas



To convert to propane/LP gas, the regulator pres-

sure must be reset also the burner inlet tting

and pilot orice must be replaced. The propane/

LP burner inlet tting is supplied with the orice

installed for a 24" log set. If you have an 18" or 30"

set, you must change this orice also.



1. Remove the burner inlet tting from the

burner pan assembly. DO NOT remove

the orice from this tting. The propane/

LP burner inlet tting is included in the

hardware kit (see Figure 11).

2. Be sure to use the correct orice for your

appliance. The hardware kit included with

this appliance contains three orices with

a cone-like shape. If you have an 18" set,

the orice for the burner inlet tting is red;

for a 30" set, it is black. If you have a 24"

log set, the orice is orange.

3. For an 18" or 30" set, use a 10 mm socket

or nut driver to install the orice from the

propane/LP burner inlet tting. Choose

the correct orice for your log set size and

install using thread sealant.

Using thread sealant (resistant to the action of

propane/LP gas) on larger end of tting, screw

the burner inlet tting through hole and into

burner manifold. Tighten using a wrench.

5 . Follow steps 3 through 13 under Natural

Gas Installation, page 5.

www.desatech.com 7901053-01J

INSTALLATION

Continued



Convert the gas control valve by changing out

the valve regulator portion of the gas valve.

Using a TORX T20 or slotted screwdriver, re-

move and discard the three mounting screws,

pressure regulator tower and diaphragm/

spring components (see Figure 13).

2. Insure that the rubber gasket is properly

positioned on the new pressure regulator

assembly. Install the new pressure regu-

lator assembly to the valve using the new

mounting screws supplied with the kit.

Tighten screws securely (approximately

25 in-lbs.) See Figure 14.

3. Install the identication label enclosed

with the gas valve regulator to the valve

body where it can easily be seen (see

Figure 14).

Figure 13 - Removing Mounting

Screws, Pressure Regulator Tower and

Diaphragm/Spring Components

Mounting

Screws

Pressure

Regulator

Tower

Diaphragm/

Spring

Components

Figure 14 - Installing Pressure Regulator

Assembly

Mounting

Screws

Rubber

Gasket

Identication

Label

Figure 15 - Installing Propane/LP Pilot Orice

Pilot

Injector



The pilot is provided with a natural gas ori-

ce installed. For propane/LP gas you must

remove it and replace it with an propane/LP

orice. The hardware kit contains an propane/

LP orice with a red stripe for converting the

pilot.

1. Gently loosen and remove the pilot line con-

nection from the bracket (see Figure 15).

2. Replace the injector (see Figure 15) with

the propane/LP pilot injector with the red

stripe.

3. Replace and tighten the pilot line to the

bracket.

4. Continue with step 6 under Natural Gas

Installation, page 5.

Note: Follow the instructions in your hearth

kit owner’s manual under the section, Testing

Burner for Leaks.



If pilot ow is weak adjustments can be made

with the pilot adjustment screw. The screw is

located below the wire harness on gas valve

body (see Figure 14).

www.desatech.com 901053-01J8

REMOTE CONTROL OPTION



If you are using the HRC100 remote control

option, you must rst connect the leads of

the receiver to the terminal block on the gas

control (see Figure 16).

1. Connect the leads to the male fast-on

terminals marked TH and TPTH.

2. Install a 9V battery (refer to the instruc-

tions included with the HRC100).

Install a 9V battery into the hand held

transmitter.

4. Insert the receiver into the simulated log

control cover, with the raised cylinder t-

ting into the hole in the cover.

5. The cover may be moved aside when op-

eration of the gas control is necessary.

Figure 16 - Connecting Wire Terminals

Control

Valve

INSTALLATION

Continued



If you choose no remote accessories at

this time, the provided jumper wire must be

installed to the terminal block on the gas con-

trol. Connect the lead to the fast-on terminals

marked TH and TPTH (see Figure 16).

OPERATION





WARNING: If you do not fol-

low these instructions exactly,

     

-



 

-





-









 

• 





    









 





-







        











LIGHTING

INSTRUCTIONS

1. STOP! Read the safety information

above.

2. Make sure equipment shutoff valve is fully

open.

3. Set selector switch to the OFF position.

WARNING: burner will come

onautomaticallywithinone minute

when the selector switch is in the



www.desatech.com 9901053-01J

Figure 17 - Control Knob and Ignitor

Button Location (Shown as Supplied, No

Control Options)

Control

Knob

Ignitor

Button

4. Press in and turn control knob clockwise

to the OFF position.

5. Wait ve (5) minutes to clear out any gas.

Then smell for gas, including near the

oor. If you smell gas, STOP! Follow “B”

in the safety information. If you don’t smell

gas, go to the next step.

6. Press in and turn control knob counter-

clockwise to the PILOT position.

Press in control knob for ve (5) seconds

(see Figure 17).

Note: You may be running this log set

for the rst time after hooking up to gas

supply. If so, the control knob may need

to be pressed in for 30 seconds or more.

This will allow air to bleed from the gas

system.

7. With control knob pressed in, press and

release ignitor button. This will light pilot.

If needed, keep pressing ignitor button

until pilot lights.

Note: If pilot does not stay lit, contact a

qualied service person or gas supplier

for repairs. Until repairs are made, light

pilot with match. To light pilot with match,

see Manual Lighting Procedure.

8. Keep control knob pressed in for 30 sec-

onds after lighting pilot. After 30 seconds,

release control knob.

• If control knob does not pop out when

released, contact a qualified service

person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4

through 8.

9. Slightly push in and turn control knob coun-

terclockwise to the ON position.

10. Wait one minute and switch selector

switch to the ON position to light burner.

11. Turn control knob clockwise to the

PILOT position, or set selector switch in

the OFF position.

OPERATION

Continued

Figure 18 - Thermopile and Pilot

Pilot

Thermopile



TO APPLIANCE



1. Turn control knob clockwise to the

OFF position.

2. If Using Optional Hand-Held Remote: Set

selector switch in the OFF position to

prevent draining battery.

3. Turn off all electrical power to appliance

if service is to be performed.

MANUAL LIGHTING

PROCEDURE

1. Follow steps 1 through 6 under Lighting

Instructions, starting on page 8.

2. Depress control knob and light pilot with

match.

3. Keep control knob pressed in for 30 sec-

onds after lighting pilot. After 30 seconds,

release control knob. Now follow steps

9 and 10, under Lighting Instructions,

column 1

www.desatech.com 901053-01J10

OPERATION

Continued

OPTIONAL REMOTE

OPERATION

Note: All remote control accessories must

be purchased separately. Follow instructions

included with the remote control



-

Lighting

Instructions

After lighting, let pilot ame burn for about one

minute. Turn control knob to ON position. Slide

the selector switch to the REMOTE position.

Note: The burner may light if hand-held remote

was on when selector switch was last turned

off. You can now turn the burner on and off with

the hand-held remote control unit.

IMPORTANT: Do not leave the selector switch

in the REMOTE or ON position when the pilot

is not lit. This will drain the battery.



Hold the control button on the hand-held

remote until burner turns on. Hold the control

button again until burner turns off.

TO LOCK press both buttons on hand-held

remote control until light stops ashing. Hand-

held remote control is now locked. If the re

is on it will be turned off automatically. In the

locked state, the light will not light up when

any button is pressed.

TO UNLOCK press both buttons together

on hand-held remote control until the light

stops ashing. The hand-held remote is now

unlocked.

Figure 19 - On/Off Hand-Held Remote

Control unit HRC100

Inhaltsverzeichnis

Andere Desa Kaminzubehör Handbücher

Desa

Desa Proflame 584 Bedienungsanleitung

Desa

Desa Wall Mantel and Base W26ME Gebrauchsanweisung

Desa

Desa DVC36 Kurzanleitung

Desa

Desa GA6050 Bedienungsanleitung

Desa

Desa GB38 Bedienungsanleitung

Desa

Desa Wall Mantel and Base W26LT Gebrauchsanweisung

Desa

Desa C32CO Gebrauchsanweisung

Desa

Desa Wall Mantel and Base W32LT Gebrauchsanweisung

Desa

Desa Wall Mantel and Base W26LC Gebrauchsanweisung

Desa

Desa W23OT Gebrauchsanweisung

Desa

Desa 102865-01 Bedienungsanleitung

Desa

Desa PC-BVBN Bedienungsanleitung

Desa

Desa GS38 Bedienungsanleitung

Desa

Desa Wall Mantel and Base W32LS2 Gebrauchsanweisung

Desa

Desa HFL200 SERIES Bedienungsanleitung

Desa

Desa Wall Mantel and Base with Trim W32WP Gebrauchsanweisung

Desa

Desa Mantel and Base W26TO Gebrauchsanweisung

Desa

Desa W32CO Gebrauchsanweisung

Desa

Desa PCDM-36VB Bedienungsanleitung

Desa

Desa Wall Mantel with Base and Trim WD26CPA Gebrauchsanweisung

Desa

Desa PC-BDV37N Bedienungsanleitung

Desa

Desa Mantel and Base W26RO Gebrauchsanweisung

Desa

Desa Wall Mantel and Base with Trim W32KCSA Gebrauchsanweisung

Desa

Desa DS37 Bedienungsanleitung

Beliebte Kaminzubehör Handbücher anderer Marken

Valor

Valor L2 1700K Bedienungsanleitung

Exodraft

Exodraft Xzense Bedienungsanleitung

Whalen

Whalen Ruso MNFP62BF23-6 Bedienungsanleitung

Lopi

Lopi Hearthview 864 Bedienungsanleitung

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Bedienungsanleitung

EdilKamin

EdilKamin SERBATOIO 250 Kurzanleitung

Bronpi

Bronpi KIT-1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Bedienungsanleitung

Superior

Superior ASD3628-TI Bedienungsanleitung

pleasant hearth

pleasant hearth OFP28WG Bedienungsanleitung

IHP

IHP Astria Series Bedienungsanleitung

Firegear

Firegear FG-H-2110SS Bedienungsanleitung

Nibe

Nibe Contura C i31 Bedienungsanleitung

kozy heat

kozy heat KZK-052 Bedienungsanleitung

SimpliFire

SimpliFire SF-WM36 Bedienungsanleitung

Bluegrass Living

Bluegrass Living BC18NR Kurzanleitung

pleasant hearth

pleasant hearth IRIS SCROLL Bedienungsanleitung