DFI SR100-N Bedienungsanleitung

SR100-N

System Board

User’s Manual

935-SR1003-050G

I02640848

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior writ-

ten permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any ex-

press or implied warranties of merchantability or fitness for any par-

ticular purpose.The user will assume the entire risk of the use or the

results of the use of this document. Further, the manufacturer re-

serves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or en-

tity of such revisions or changes.

Trademarks

Product names or trademarks appearing in this manual are for iden-

tification purpose only and are the properties of the respective own-

ers.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation.This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following meas-

ures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

About this Manual................................................................................

Warranty.................................................................................................

Static Electricity Precaution................................................................

Safety Measures.....................................................................................

About the Package...............................................................................

Before Using the System Board.........................................................

Chapter 1 - Introduction....................................................................

Specifications...................................................................................................................................

Features..............................................................................................................................................

Chapter 2 - Hardware Installation....................................................

System Board Layout ..........................................................................................................

System Memory..........................................................................................................................

CPU.......................................................................................................................................................

Jumper Settings............................................................................................................................

Rear Panel I/O Ports.............................................................................................................

I/O Connectors..........................................................................................................................

Chapter 3 - BIOS Setup......................................................................

Award BIOS Setup Utility.................................................................................................

Updating the BIOS..................................................................................................................

Chapter 4 - Supported Softwares.....................................................

Drivers for Windows Vista System..........................................................................

Drivers for Windows XP System..............................................................................

Appendix A - Watchdog Timer.............................................................

Appendix B - Troubleshooting..........................................................

Appendix C - Frequently Asked Questions....................................

Appendix D - Hot Keys for Graphics Display...............................

113

130

132

136

138

About this Manual

An electronic file of this manual is included in the CD. To view the

user’s manual in the CD, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product specifica-

tions.

2. The warranty is void if the product has been subjected to physi-

cal abuse, improper installation, modification, accidents or unau-

thorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service, adjust-

ments or repairs on the product, whether in or out of warranty.

It must be returned to the purchase point, factory or authorized

service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board,

components or devices even before installing them in your system

unit. Static electrical discharge can damage computer components

without causing any signs of physical damage. You must take extra

care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its

anti-static bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of

the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connec-

tors. Hold modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor,

disk drive and other components. Perform the upgrade in-

struction procedures described at an ESD workstation

only. If such a station is not available, you can provide

some ESD protection by wearing an antistatic wrist strap

and attaching it to a metal part of the system chassis. If a

wrist strap is unavailable, establish and maintain contact

with the system chassis throughout any procedures requir-

ing ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to local ordinance.

Introduction

About the Package

The system board package contains the following items. If any of

these items are missing or damaged, please contact your dealer or

sales representative for assistance.

;The system board

;One IDE cable

;One bracket mounted with 2 USB ports

;One Serial ATA data cable

;One Serial ATA power cable

;One “Main Board Utility” CD

;Two floppy diskettes

;One I/O shield

;One QR (Quick Reference)

The system board and accessories in the package may not come

similar to the information listed above.This may differ in accordance

to the sales region or models in which it was sold. For more infor-

mation about the standard package in your region, please contact

your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need

at least the following internal components.

•A CPU

•Memory module

•Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use

which will normally include at least a keyboard, a mouse and a video

display monitor.

Introduction

Processor

Chipset

System Memory

BIOS

Energy Efficient

Design

Damage Free

Intelligence

Audio

Chapter 1 - Introduction

• Intel®CoreTM2 Duo mobile processor

- 800/533MHz system data bus

• Intel®Celeron®M 500 series processor for mobile Intel®965

Express chipset

• Processor socket: mPGA478P

• Intel®chipset

- Northbridge: Intel®GM965/GME965 Express chipset

- Southbridge: Intel®82801HBM ICH8M

• Two 200-pin SODIMM sockets

• Supports 533MHz and 667MHz DDR2 SDRAM

• Supports maximum of 4GB system memory

• Award BIOS

• 8Mbit flash memory

• Supports ACPI specification 2.0/1.0

• Supports ACPI STR (Suspend to RAM) function

• Wake-On-Events include:

- Wake-On-PS/2 Keyboard/Mouse

- Wake-On-Ring

- Wake up by PCI card

- PCI Express PME

- USB KB/MS Wake up from S3

- RTC timer to power-on the system

• Enhanced Intel®SpeedStep Technology

• Intel®Rapid Memory power management

• Dynamic FSB frequency switching

• AC power failure recovery

• Monitors CPU/system temperature and overheat alarm

• Monitors CPU(V)/3.3V/5V/12V/VBAT(V)/5VSB(V) voltages and

failure alarm

• Monitors CPU/system fan speed and failure alarm

• Read back capability that displays temperature, voltage and fan

speed

• Watchdog timer function

• Realtek ALC262 2-channel High Definition Audio

• Two 24-bit stereo DACs and three 20-bit stereo ADCs

• S/PDIF input/output interface

Specifications

Introduction

Graphics

LAN

Serial ATA

IDE

Rear Panel I/O

Ports

I/O Connectors

• Internal graphics feature

- Mobile Intel®Graphics Media Accelerator X3100

- Dynamic Video Memory Technology 4.0

- Microsoft DirectX 9x

- OpenGL 1.5

• Integrated graphics interface

- Analog CRT

- Integrated 300MHz RAMDAC

- Analog monitor supports up to QXGA (2048x1536@60Hz)

- LVDS

- 25MHz-112MHz single/dual channel, TFT panel type support

- Single / dual channel LVDS interface: 2x24 bpp panel

supports up to WUXGA (1920x1200@65Hz) or UXGA

(1600x1200@75Hz)

- DVI (DVI-D signal only)

- DVI 1.0 support for external digital monitor

• Two Realtek RTL8111B PCI Express Gigabit controllers

• Suppor ts 10Mbps, 100Mbps and 1Gbps data transmission

• IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) compliant

• Three Serial ATA ports, compliant with SATA 1.0a specification

• Data transfer rate up to 3Gb/s

• Supports Advanced Host Controller Interface (AHCI)

• Supports up to two IDE devices

• Supports Ultra ATA 100/66/33

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 2 DB-9 serial ports

• 1 DB-15 VGA port

• 1 DVI-I port (DVI-D signal only)

• 2 RJ45 LAN ports

• 4 USB 2.0/1.1 ports

• Mic-in, line-in and line out jacks

• 2 connectors for 4 additional external USB 2.0/1.1 ports

• 1 LCD brightness control connector

• 1 LVDS LCD panel connector

• 1 LCD/inverter power connector

• 1 LCD AUX power connector

• 1 DIO connector

• 1 front audio connector for line-out and mic-in jacks

• 1 CD-in internal audio connector

• 1 S/PDIF connector

• 3 Serial ATA connectors

• 1 40-pin IDE connector

• 1 20-pin ATX power connector

• 1 front panel connector

• 1 chassis open connector

• 2 fan connectors

Introduction

Expansion Slots

Temperature

Humidity

PCB

• 1 PCI slot for PCI expansion card or customized riser card for 1,

2 or 3 PCI slots expansion

•0

oC to 60oC

• 10% to 90%

• 8 layers, Mini-ITX form factor

• 17cm (6.7") x 17cm (6.7")

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI 915P-TAL Bedienungsanleitung

DFI

DFI KT600-AL Bedienungsanleitung

DFI

DFI PB64-V3 Bedienungsanleitung

DFI

DFI G7B630-N Bedienungsanleitung

DFI

DFI AD72-SC Bedienungsanleitung

DFI

DFI P4M266A-MLV Bedienungsanleitung

DFI

DFI FS051 Bedienungsanleitung

DFI

DFI 865PE-ML Bedienungsanleitung

DFI

DFI NS80-EA Bedienungsanleitung

DFI

DFI CS65-SC Bedienungsanleitung

DFI

DFI CW35-TC Bedienungsanleitung

DFI

DFI Qseven FS700 Series Bedienungsanleitung

DFI

DFI 848P-AL Bedienungsanleitung

DFI

DFI KD171 Bedienungsanleitung

DFI

DFI CMS632-W480E Bedienungsanleitung

DFI

DFI G586IPV Bedienungsanleitung

DFI

DFI CMS631-Q470E Bedienungsanleitung

DFI

DFI NB32-SC Bedienungsanleitung

DFI

DFI 865PE-ALE Bedienungsanleitung

DFI

DFI K6XV3+ Bedienungsanleitung

DFI

DFI PB61-V3 Bedienungsanleitung

DFI

DFI COM630-B Bedienungsanleitung

DFI

DFI CS631-C246 Bedienungsanleitung

DFI

DFI NS30-SC/SL Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung