DFI VP101-BT Bedienungsanleitung
1
VP101-BT Installation Guide
Package Contents
DFI reserves the right to change the specications at any time prior to the product's release. For the latest revision and details of the
installation process, please refer to the user's manual.
www.d.com
Note:
The CD that came with the system contains an autorun screen to install drivers, utilities,
and software applications required to enhance the performance of the system and a user's
manual for your reference. Insert the CD into a CD-ROM drive. The autorun screen will ap-
pear. If after inserting the CD, “Autorun” did not automatically start, please go directly to
the root directory of the CD and double-click “Setup”. Please install all required drivers.
•
1 VP101-BT system unit
• 6
Mounting screws for Mini PCIe module
•
1 Quick Installation Guide
•
1 Disk includes:
- Drivers / Manual
2
Panel
Bottom View
Top View
Note:
You can choose to wire the COM 4 port to be a CANbus (Controller Area Network)
interface instead.
VGA
USB 2.0
LAN 2
Line-out
LAN 1 MIC-in
VCC/ACC/GND
(Connects to car battery)
COM 3
(RS232/RS422/RS485)
COM 5
(RS232)
Antenna
hole
COM 1/2
(RS232/RS422/RS485)
HDMI
COM 4/ 8-bit DIO
CANbus*
USB 3.0
Reset switch/
Status LED
Power button
3
4. After removing the mounting screws, lift the bottom side of the chassis
cover to open the system. The Mini PCIe and the micro SD slots will be
readily accessible.
Removing the Chassis Cover
Please observe the following guidelines and follow the procedure to open the system.
1. Make sure the system and all other peripheral devices connected to it have
been powered off.
2. Disconnect all power cords and cables.
3. The 12 mounting screws on the bottom and two sides of the system are used
to secure the cover to the chassis. Remove these screws and then put them in
a safe place for later use.
Chassis screw
Power board
micro SD
Mini PCIe slots
Mini PCIe slots
4
Installing a Mini PCIe Card
The system board is equipped with 3 Mini PCIe slots: two full-size and one half-
size slots. Here we will demonstrate the installation of a half-size Mini PCIe card
(
PCIe/USB/LPC signals
) for WiFi connection.
1. Grasp the Mini PCIe card by its edges and align the notch in the connector of
the card with the notch in the connector on the system board.
2. Push the Mini PCIe card down and use the provided mounting screws to se-
cure the card on the system board.
Note:
The system also has two additional full-size Mini PCIe slots that use PCIe (PCIe/
USB/3G/GPRS/CANbus signals) and mSATA (SATA signals) interfaces.
Mounting screw
5
Installing a SATA Drive
The system can accomondate one SATA drive. Please use the following procedure
to install a SATA drive into the system.
2. Install the SATA drive on the HDD bracket. Place the HDD bracket back to the
system and secure the drive in place with the provided mounting screws.
1. SATA HDD bay is located under the power board. Please remove the
power board rst to uninstall the HDD bracket.
SATA connectors
on the board
SATA connectors
SATA
Mounting screws
Power board
Mounting screws
SATA bracket
Mounting screws
6
The wall mount kit includes the following:
• 2 wall mount brackets
• Bracket screws
1. Select a place on the wall where you will mount the system.
2. Use the provided mounting screws to attach “wall mount bracket 1” to
the wall.
Mounting Options
Wall mount
Wall mount bracket 1 Wall mount bracket 2
Wall mount bracket 1
Mounting screw
7
3. Attach the other bracket (wall mount bracket 2) to the rear of the
system.
4. Slide the system to "wall mount bracket 1" to attach the two brackets with the
hooks. Then tighten the screw to secure the assembly in place.
Screw
Wall mount bracket 2
Mounting screw
Mounting screw
Hooks
8
1. Select a place on the panel (or wall) where you will mount the system.
2. Cut out a shape on the panel that corresponds to the system’s rear di-
mensions (272mm x 169mm) and ensure that the system can be tted
into the panel properly.
3. Insert the system from the outside surface of the panel into the mount-
ing hole until it is properly tted against the panel.
4. Position the mounting clamps along the rear edges of the system and
insert them into the slits around the system.
www.d.com
Panel mount
The panel mounting kit includes the following:
• 6 mounting clamps
132.20
210.50
5
Panel
Mounting hole
272
169
9
5. The rst and second clamps must be positioned and secured diagonally prior
to mounting the rest of the clamps. Tighten the clamp’s screw using an electric
screwdriver by pressing the white plastic cap onto the back of the panel. The
illustration below shows that all clamps are properly mounted.
272
169
Slit for mounting the clamp
Mounting clamp
White plastic cap
10
Board Layout and Jumper Settings
TOP BOTTOM
LAN 1
LAN 2
DDR3L
DDR3L
DDR3L
DDR3L
Mini PCIe with SIM
COM 4
1210
31
JP22 1
1
1
(JP20)
(JP18)
(JP17)
(JP21)
1 3
1210
COM 2
USB 0
USB 3.0
HDMI
Reset
Power
DC-in
USB 2
USB 7
USB 1
USB 6
COM 3
1
Battery
Buzzer
1
Chassis
Intrusion
1
Clear CMOS
Data (JP24)
SPI
Flash
BIOS
eMMC
(optional)
iTE
IT8528E
Mini PCIe with LPC mSATA
MicroSD
(optional)
1
System Fan
1
USB 0
Power
Select
(JP5)
1
1 1
USB 1-2
Power Select (JP6)
USB 5-7 Power
Select (JP7)
(JP25)
USB 2.0
(JP17)
(JP20)
COM 4/DIO Select (JP22, JP21)
Digital I/O 0-3 Output State
Digital I/O Power Select
Auto
Power-on
Select
(JP18)
Digital I/O 4-7 Output State
VGA
DC-in
from
Power board
DDR3L
DDR3L
DDR3L
DDR3L
DDR3L
Intel Atom
E3800 Series
Intel
WGI210AT
Nuvoton
NCT6106D
ASMedia
ASM1442
Intel
WGI210AT
SMSC
USB4604
SIM Card
NXP
PTN3460
Standby
Power LED
www.d.com
USB Power Select: 0 (JP5), 1-2
(JP6), 5-7 (JP7)
+5V_standby (default) 1-2 On
+5V 2-3 On
Clear CMOS Data JP24
Normal (default) 1-2 On
Clear CMOS Data 2-3 On
Auto Power-on Select JP25
Power-on via power button 1-2 On
Power-on via AC power
(default)
2-3 On
Note:
You cannot use COM 4 and DIO at the same
time. Please adjust JP21 and JP22 together.
Digital I/O Output State JP18 (DIO 4-7)
JP20 (DIO 0-3)
GND (default) 1-2 On
+5V or +5V_standby 2-3 On
Digital I/O Power Select JP17
+5V_standby 1-2 On
+5V (default) 2-3 On
COM 4/DIO Select JP21, JP22
C O M 4 ( d e f a u l t ) 1-2, 4-5
7-8, 10-11 On
DIO 2-3, 5-6
8-9, 11-12 On
Andere Handbücher für VP101-BT
1
Inhaltsverzeichnis
Andere DFI Touchscreen Handbücher
DFI
DFI KS-SD Series Bedienungsanleitung
DFI
DFI KS150-BT Bedienungsanleitung
DFI
DFI TPC121 Installationsanleitung
DFI
DFI TPC150-SD Bedienungsanleitung
DFI
DFI KS101-BT Bedienungsanleitung
DFI
DFI TPC170 Installationsanleitung
DFI
DFI KS230 Bedienungsanleitung
DFI
DFI KS070-AL Bedienungsanleitung
DFI
DFI VS 15 Bedienungsanleitung
DFI
DFI KS150 Bedienungsanleitung
DFI
DFI KS104-CD Bedienungsanleitung
DFI
DFI KS200 Bedienungsanleitung
DFI
DFI KS070-ALE39P Bedienungsanleitung
DFI
DFI VP070-M8M Bedienungsanleitung
DFI
DFI KS057R-FS Bedienungsanleitung
DFI
DFI KS150-BT Bedienungsanleitung
DFI
DFI KS156-AL Bedienungsanleitung
DFI
DFI KS070-FS Bedienungsanleitung
DFI
DFI VP070-M8M Bedienungsanleitung
DFI
DFI TPC121 Bedienungsanleitung
Beliebte Touchscreen Handbücher anderer Marken
IBASE Technology
IBASE Technology ASTUT-152-RE1S Bedienungsanleitung
YASKAWA
YASKAWA TP 610C Bedienungsanleitung
B&R
B&R Power Panel C Series Bedienungsanleitung
Beijer Electronics
Beijer Electronics X2 control Bedienungsanleitung
AXIOMTEK
AXIOMTEK GOT321W-521 Bedienungsanleitung
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Bedienungsanleitung
