Diesse MINI-CUBE Bedienungsanleitung

July 2021

QUICK START GUIDE

REFER TO THE USER MANUAL FOR ALL DETAILS

PERFORMING AN ANALYSIS CYCLE

- Switch on the instrument

- Click START

Wait for the instrument to complete the initialization phase

Gently invert the tube 10-12 times for complete

inversion of the tube so that the air bubble that forms run through it

from one end to the other, immediately before starting the analysis.

From this moment on, it is possible to introduce the sample for testing.

To start a cycle, insert the tubes orienting them as shown in the

photo in one of the free positions. If a barcode reader (optional) is

present, read the sample identification code before inserting the

tube. After insertion, the instrument scans to determine the blood

level at zero sedimentation time.

During the first scan a “CHECK TUBE” pop-up window appears which determines the

display of the tube type (normal or pediatric) and the blood level, after which the

countdown will be activated.

Procedure for map TUBES (BD MICROTAINER®, MICROVETTE® APT

(SARSTEDT))

To analyze a MAP tube sample, touch the screen in one of the

empty positions to open the NEW SAMPLE window.

Select “Microtube MAP” YES (Y) and insert the tube in one of the

free positions.

The tube will be represented as a pediatric tube, with the letter

M on the cap, indicating that they are MAP tubes.

If most of the tubes are BD Microtainer® MAP, in the settings menu, MICROTUBE MAP

parameter, select ON.

July 2021

EXECUTION OF ANALYSIS CYCLE - RANDOM ACCESS

- During a cycle it will be possible at any time to insert a new sample in each of the free

positions present.

- Mix the sample thoroughly before inserting it into the instrument as described above

RESULTS

At the end of the 20 minutes (14 min for Pediatric) the instrument displays the result.

Green color indicates ESR within the normal range.

Red color indicates an ESR that has exceeded the normal level.

The results are expressed in mm / h (Westergren 1st hour).

The results can be printed via Bluetooth printer (Optional)

You will need to connect it to the instrument first from the menu.

Printing can take place automatically at the end of the analysis, or

- Press the ARCHIVE key

- Select the samples for consultation / printing of the results

QUALITY CONTROL

Entering the settings menu, under QC, you can enter the

characteristics of each control, just read the bar code of the QC

Diesse. Then, every time the control is inserted in any position of

the instrument, it will be recognized as QC, and displayed on the

screen, as shown in the image.

The tube with the white cap indicates the Normal control, the

one with the black cap the Pathological control.

In case you are using another trade control, it is recommended that you

create dedicated barcode labels and manually enter the data.

REFILL

- Press the SETTINGS button

- Select REFILL on the second page

- Insert the TEST DEVICE NEXT in the appropriate compartment

(as shown in the figure)

- Press the CHECK key

- Press OK to confirm the test number to reload

- Automatic update of the number of tests displayed on the

instrument screen (top left)

July 2021

TROUBLESHOOTING

ERROR MESSAGES

CAUSE

REMEDY

Remove all test tubes

A cycle was started with some

tubes already inserted.

Otherwise, there may be a

foreign body in front of the

sensors.

Remove the tubes and restart the run.

Turn off the instrument, turn it over and try to

clean it internally. If the problem persists,

contact technical assistance.

Low (Lo)

Blood level inside the tube too

low

If possible, add blood up to established levels.

High (HI)

- Blood level inside the tube too

high

-Interference caused by labels

- If possible, remove blood up to the

established levels

- Try to reposition the tube as described

previously

ERR

Generic error, pressing on the

error message a number will

appear that differentiates the

cause.

See complete troubleshooting

in the User Manual

- Check that the tube used is compatible with

the instrument or the possible presence of a

number of labels greater than 2 in case remove

the excess labels. Check for any lumps or clots.

- Try to repeat the test

Printer error, retry?

Printer not found.

Make sure the printer is turned on. Otherwise,

deselect the Bluetooth mode (OFF)

Exam not available. Need refill

The executable test counter is

equal to zero

Follow the instructions to recharge the

instrument with a new transponder described

in chapter 4.

USB pendrive not found

The instrument does not

recognize the USB stick.

Remove and reinsert the USB stick or change

it.

Warning! Remain n tests

The number of tests remaining

is less than 50

It is recommended to recharge the instrument

as soon as possible with a new transponder

CHECK DEVICE already used

The transponder used is empty.

Use a new transponder

CHECK DEVICE not found

The instrument does not

recognize the transponder used

Remove and reinsert the transponder. Use

another transponder

Enrica Gentile

Junior customer care specialist

DIESSE Diagnostica Senese SpA

Andere Handbücher für MINI-CUBE

Andere Diesse Laborausrüstung Handbücher

Diesse

Diesse MINI-CUBE Bedienungsanleitung

Diesse

Diesse VES-MATIC 30 Bedienungsanleitung

Diesse

Diesse CHORUS AUTOSAMPLER Bedienungsanleitung

Diesse

Diesse cube 30 touch Bedienungsanleitung

Diesse

Diesse cube 30 touch Bedienungsanleitung

Diesse

Diesse cube 30 touch Bedienungsanleitung

Diesse

Diesse MINI-CUBE Bedienungsanleitung

Diesse

Diesse VES-MATIC CUBE 30 Bedienungsanleitung

Diesse

Diesse cube 30 touch Bedienungsanleitung

Diesse

Diesse cube 30 touch Bedienungsanleitung

Diesse

Diesse VES MATIC CUBE 80 Bedienungsanleitung

Diesse

Diesse Chorus Bedienungsanleitung

Diesse

Diesse CHORUS AUTOSAMPLER Bedienungsanleitung

Diesse

Diesse MINI-CUBE Bedienungsanleitung

Diesse

Diesse VES MATIC Original Bedienungsanleitung

Diesse

Diesse CHORUS SPECIFIC IgE Bedienungsanleitung

Diesse

Diesse Ves-Matic Cube 200 Bedienungsanleitung

Diesse

Diesse VES-MATIC 20 Bedienungsanleitung

Diesse

Diesse CHORUS TRIO CHORUS EXPANDER UPGRADE KIT Bedienungsanleitung

Diesse

Diesse Chorus Trio Bedienungsanleitung

Diesse

Diesse VES MATIC 5 Bedienungsanleitung

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung