Digital Equipment VAX 4000 100 Service-Handbuch

VAX4000

Model100

InstallationInformation

Order Number: EK–465AA–IN. A01

September 1992

This manual describes how to install and test the VAX 4000 Model 100.

Revision Information: This is a new manual.

Digital Equipment Corporation

Maynard, Massachusetts

September 1992

The information in this document is subject to change without notice and should not be

construed as a commitment by Digital Equipment Corporation. Digital Equipment Corporation

assumes no responsibility for any errors that may appear in this document.

The software described in this document is furnished under a license and may be used or copied

only in accordance with the terms of such license.

No responsibility is assumed for the use or reliability of software on equipment that is not

supplied by Digital Equipment Corporation or its afﬁliated companies.

Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to

restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer

Software clause at DFARS 252.227-7013.

The postpaid Reader’s Comments forms at the end of this document request your critical

evaluation to assist in preparing future documentation.

The following are trademarks of Digital Equipment Corporation: DEC, Digital, ThinWire, VAX,

VAX DOCUMENT, VMS, and the DIGITAL logo.

S2009

This document was prepared using VAX DOCUMENT, Version 2.1.

Contents

Preface ..................................................... v

1 Installation Procedure

Step 1: Choosing a Suitable Location . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1

Step 2: Unpacking the System and Identifying the Parts . . . . . . . . . . . . 1–2

Step 3: Connecting the Console Terminal . . . . . . . . . . . . . . . . . . . . . . . . 1–3

Step 4: Connecting the ThinWire Terminator . . . . . . . . . . . . . . . . . . . . . 1–4

Step 5: Connecting the SCSI Terminator . . . . . . . . . . . . . . . . . . . . . . . . . 1–5

Step 6: Connecting the DSSI Terminator . . . . . . . . . . . . . . . . . . . . . . . . . 1–6

Step 7: Connecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7

Step 8: Turning on the Console Terminal and System Unit . . . . . . . . . . . 1–8

Step 9: Checking the Power-Up Test Results . . . . . . . . . . . . . . . . . . . . . . 1–9

Step 10: Connecting the System to a Network . . . . . . . . . . . . . . . . . . . . . 1–11

Step 11: Connecting External Options to the System . . . . . . . . . . . . . . . 1–11

Step 12: Booting the Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . 1–11

Examples

1–1 Successful Power-Up Test Screen . . . . . . . . . . . . . . . . . . . . . . 1–9

1–2 Unsuccessful Power-Up Test Screen . . . . . . . . . . . . . . . . . . . . 1–10

Figures

1–1 The VAX 4000 Model 100 System . . . . . . . . . . . . . . . . . . . . . 1–2

1–2 ConsoleConnection ................................ 1–3

1–3 ThinWireTermination .............................. 1–4

1–4 Connecting the SCSI Terminator . . . . . . . . . . . . . . . . . . . . . . 1–5

1–5 Connecting the DSSI Terminator . . . . . . . . . . . . . . . . . . . . . . 1–6

1–6 Power Cord Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7

1–7 PowerTurnOn ................................... 1–8

iii

Preface

This manual describes how to install and test the VAX 4000 Model 100. It

also refers to information on connecting the system to a network, connecting

external options to the system, and booting the operating system.

Audience

This manual is intended for anyone who wants to install the VAX 4000

Model 100. It is written for both experienced and inexperienced users.

Structure of This Manual

This manual contains one chapter. Each section heading is a step in the

installation procedure and is indicated by the word step and a numeral.

Substeps in the procedure are indicated by a numeral.

Additional Information

See the VAX 4000 Model 100 Operator Information manual for the list of

associated and related documents.

Conventions

The following conventions are used in this manual:

Convention Description

MONOSPACE

Text displayed on the screen is shown in monospace type.

italic type Italic type emphasizes important information and indicates the

complete titles of manuals.

Note A note contains information that is of special importance to the user.

Installation Procedure

This chapter shows you, step by step, how to install the VAX 4000 Model 100.

Step 1: Choosing a Suitable Location

Follow these guidelines when choosing where to place the system unit:

• Place the system unit where the room temperature is between 10°C and

40°C (50°F and 104°F) and the humidity is between 20% and 80%.

• Place the system unit at least 1 metre (3 feet) from heaters, photocopying

machines, or other operating equipment.

• Place the system unit in a well-ventilated location.

• Place the system unit on a work surface that is raised above the ﬂoor.

• Do not place this unit on the top of any pedestal system.

• Keep the air vents on either side of the system unit clear.

• Do not expose the system unit to direct sunlight or abrasive particles.

Note

The console terminal is not supplied with the system.

Installation Procedure 1–1

Step 2: Unpacking the System and Identifying the Parts

1. Unpack the system.

2. Make sure that you have all the parts listed on the packing slip. The

loose-piece accessory kit is shipped with all basic systems. If you do not

have all the parts listed, contact your Digital Sales representative.

Figure 1–1 The VAX 4000 Model 100 System

7 8

MLO-009274

.....

....



System Unit



SCSI Terminator H8574-A (PN 12-30552-01)



One ThinWire™ Ethernet T-Connector (H8223) and Two Terminators

(H8225)



Standard Ethernet Loopback Connector (12-22196-01)



DEC423 Terminal Cable (BC16E-25)



DSSI Terminator (12-29258-01)



Power Cord



Documentation and Software Licenses

1–2 Installation Procedure

Step 3: Connecting the Console Terminal

1. Connect one end of the terminal cable to the modiﬁed modular jack (MMJ)

port 3. This system will be shipped with a label covering ports 0 and 1.

After port 3 is properly identiﬁed as the console port, the OPA0 arrow label

may be removed.

2. Connect the other end of the terminal cable to a DEC423 (MMJ)

communications port on the console terminal.

Figure 1–2 Console Connection

MLO-009275



Terminal Cable

Installation Procedure 1–3

Step 4: Connecting the ThinWire Terminator

1. Assemble the T-connector and the two terminators to form a ThinWire

terminator.

2. Connect the ThinWire terminator to the system unit.

Figure 1–3 ThinWire Termination

MLO-009276

1 22



T-Connector



Terminator

1–4 Installation Procedure

Step 5: Connecting the SCSI Terminator

1. Connect the SCSI terminator to the SCSI port.

2. Close the bail lock loops.

Figure 1–4 Connecting the SCSI Terminator

MLO-009696



SCSI Terminator

Installation Procedure 1–5

Andere Handbücher für VAX 4000 100

Inhaltsverzeichnis

Andere Digital Equipment Desktop Handbücher

Digital Equipment

Digital Equipment Personal DECstation 5000 50 Handbuch

Digital Equipment

Digital Equipment DIGITAL Personal Workstation Installations- und Betriebshandbuch

Digital Equipment

Digital Equipment VAX 4000 105A Leitfaden

Digital Equipment

Digital Equipment VAXstation 2000 Montage- und Wartungsanleitung

Digital Equipment

Digital Equipment DEC 3000 600 AXP Bedienungsanleitung

Digital Equipment

Digital Equipment Starion Minitower PC 919 Bedienungsanleitung

Digital Equipment

Digital Equipment VAX 4000 Model 100 Kurzanleitung

Digital Equipment

Digital Equipment DEC 3000 700 AXP Kurzanleitung

Digital Equipment

Digital Equipment DECstation 5000 Kurzanleitung

Digital Equipment

Digital Equipment DECstation 2100 Handbuch

Digital Equipment

Digital Equipment VT420 Bedienungsanleitung

Digital Equipment

Digital Equipment DECstation 212LP Bedienungsanleitung

Digital Equipment

Digital Equipment DECstation 5000 Model 200 Bedienungsanleitung

Digital Equipment

Digital Equipment VAX 4000 500A Bedienungsanleitung

Digital Equipment

Digital Equipment PDP-11/23-PLUS Benutzerhandbuch

Digital Equipment

Digital Equipment DECpc LP Bedienungsanleitung

Digital Equipment

Digital Equipment VAXstation 4000 VLC Bedienungs- und Montageanleitung

Digital Equipment

Digital Equipment DEC 3000 Bedienungsanleitung

Digital Equipment

Digital Equipment VT100 Bedienungsanleitung

Digital Equipment

Digital Equipment VAX 4000 Model 100 Technische Daten

Digital Equipment

Digital Equipment VT18X Bedienungsanleitung

Digital Equipment

Digital Equipment DEC 3000 Bedienungs- und Montageanleitung

Digital Equipment

Digital Equipment VAXstation 4000/90 Series Benutzerhandbuch

Digital Equipment

Digital Equipment DECpc AXP 150 Handbuch

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

HP Z1 Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung