Digital Equipment VAXft 810 Service-Handbuch

VAXftSystems

Model810

InstallationInformation

Order Number: EK-VXFTA-IN. A01

June 1993

This manual is intended for use by Digital Customer Services and other

personnel responsible for installing VAXft Model 810 systems.

Digital Equipment Corporation

June 1993

The information in this document is subject to change without notice and should not be construed

as a commitment by Digital Equipment Corporation. Digital Equipment Corporation assumes no

responsibility for any errors that may appear in this document.

No responsibility is assumed for the use or reliability of software on equipment that is not supplied

by Digital Equipment Corporation or its afﬁliated companies.

Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions

as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software

clause at DFARS 252.227-7013.

Printed in U.S.A.

The following are trademarks of Digital Equipment Corporation: CompacTape, OpenVMS, ThinWire,

TK, UETP, VAX, VAXft, VMS, and the DIGITAL logo.

FCC NOTICE: This equipment generates, uses, and may emit radio frequency energy. It has been

tested and found to comply with the limits for a Class A computing device pursuant to Subpart J

of Part 15 of FCC rules of operation in a commercial environment. This equipment, when operated

in a residential area, may cause interference to radio/TV communications. In such event the user

(owner), at his own expense, may be required to take corrective measures.

This document is available on CDROM.

Documentation Map

Overview

Information

(VAXft Systems)

Software

Information

(VAXft System Services)

Operating System

(VMS)

Hardware

Information

(VAXft Systems)

Manager’s

Guide

MR−6228−RA

Reference

Manual

Software Product

Description

Owner’s Manual

Site Prep and

Installation Guide

Service

Installation

Information

Models Model

110, 410, 610, 612 810

Bookreader

Online

Book Tape

Network

Device Drivers

Before You

Install Letter

Maintenance

Guide

Operating

Information

Release Notes

VMS Upgrade and

Installation Manual

VMS Upgrade and

Installation Supplement:

VAXft Systems

VMS Volume

Shadowing Manual

Cover

Letter

Using Factory−Installed

Software with

VAXft Systems

= Letter

= Order Separately

VAX Wide Area

Configuration

Guide

Release Notes

Online Help

the Model 810

Configuring

Site Prep

Information

iii

Contents

1 System Inspection and Unpacking

1.1 InThisChapter............................................. 1–1

1.2 UnloadingtheSystem ........................................ 1–1

1.3 InspectingtheShipment ...................................... 1–2

1.4 MovingtheShipment......................................... 1–2

1.5 UnpackingtheOptions ....................................... 1–3

1.6 Opening the Shipping Cartons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4

1.7 UnpackingtheCabinets....................................... 1–6

1.8 DeskiddingtheCabinets ...................................... 1–8

2 Cabinet Assembly and Cable Installation

2.1 InThisChapter............................................. 2–1

2.2 Entry System Interface Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1

2.3 EntrySystemPowerCabling................................... 2–3

2.4 Expanded System Cabinet Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4

2.5 Expanded System Cabinet Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6

2.6 Expanded System Interface Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8

2.6.1 DSSI and Ethernet Conﬁgurations . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8

2.7 Expanded System Power Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–16

3 Completing the System Installation

3.1 InThisChapter............................................. 3–1

3.2 Power Preparation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1

3.3 TurningOnSystemPower..................................... 3–1

3.4 Turning Off Zone and System Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4

3.5 Setting the Terminal Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–5

3.6 FinalSystemTests........................................... 3–5

A Cabinet and Component Descriptions

A.1 InThisAppendix............................................ A–1

A.2 CPUandExpansionCabinets .................................. A–1

A.3 ZoneControlPanel .......................................... A–6

A.4 PowerModules.............................................. A–8

A.5 Domestic and International Power Distribution Boxes . . . . . . . . . . . . . . . . A–9

Figures

1–1 Opening a Cabinet Shipping Carton . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5

1–2 UnpackingaCabinet...................................... 1–7

1–3 Attaching the Deskidding Ramps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–9

2–1 Console Module Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3

2–2 CabinetPanels........................................... 2–5

2–3 AssemblingtheCabinets ................................... 2–7

2–4 DSSICablingExample1................................... 2–9

2–5 Card Cage Cabling for Example 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10

2–6 Zone A and B Interface Module Card Cages . . . . . . . . . . . . . . . . . . . . 2–11

2–7 Device and Cable Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–13

2–8 Console Module Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–14

2–9 DSSICablingExample2................................... 2–15

3–1 Power Module Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . 3–3

A–1 Cabinet Layout, Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–2

A–2 CabinetLayout,RearView ................................. A–4

A–3 ZoneControlPanel ....................................... A–6

A–4 Power Module Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . A–8

A–5 Domestic Power Distribution Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–10

A–6 International Power Distribution Box . . . . . . . . . . . . . . . . . . . . . . . . . A–11

Tables

1–1 InspectingtheShipment ................................... 1–2

1–2 MovingtheShipment...................................... 1–2

1–3 UnpackingtheOptions .................................... 1–3

1–4 Opening the Shipping Cartons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4

1–5 Key to Figure 1–1, Opening a Cabinet Shipping Carton . . . . . . . . . . . 1–5

1–6 UnpackingtheCabinets.................................... 1–6

1–7 Key to Figure 1–2, Unpacking a Cabinet . . . . . . . . . . . . . . . . . . . . . . . 1–7

1–8 DeskiddingtheCabinets ................................... 1–8

1–9 Key to Figure 1–3, Attaching the Deskidding Ramps . . . . . . . . . . . . . . 1–9

2–1 Entry System Interface Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1

2–2 TA85TapeDriveCabling................................... 2–3

2–3 PowerCableCountryKits.................................. 2–4

2–4 Preparing the Cabinets for Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4

2–5 Key to Figure 2–2, Cabinet Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5

2–6 AssemblingtheCabinets ................................... 2–6

2–7 Key to Figure 2–3, Assembling the Cabinets . . . . . . . . . . . . . . . . . . . . 2–6

2–8 SupportedDeviceNodes.................................... 2–8

2–9 Summary of Example 1 DSSI Cabling Rules . . . . . . . . . . . . . . . . . . . . 2–9

2–10 Detail of Example 1 System Interface Cabling . . . . . . . . . . . . . . . . . . . 2–12

2–11 Example 1 System Power Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–16

2–12 PowerCableCountryKits.................................. 2–16

3–1 Power Preparation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1

3–2 TurningOnSystemPower.................................. 3–2

3–3 Key to Figure 3–1, Power Module Controls and Indicators . . . . . . . . . 3–2

3–4 TurningOffZonePower.................................... 3–4

3–5 TurningOffSystemPower.................................. 3–4

3–6 RunningFinalSystemTests ................................ 3–5

A–1 Key to Figure A–1, Cabinet Layout, Front View . . . . . . . . . . . . . . . . . A–3

A–2 Key to Figure A–2, Cabinet Layout, Rear View . . . . . . . . . . . . . . . . . . A–5

A–3 Key to Figure A–3, Zone Control Panel . . . . . . . . . . . . . . . . . . . . . . . . A–7

A–4 Key to Figure A–4, Power Module Controls and Indicators . . . . . . . . . A–9

A–5 Key to Figure A–5, Domestic Power Distribution Box . . . . . . . . . . . . . A–10

A–6 Key to Figure A–6, International Power Distribution Box . . . . . . . . . . A–11

vii

System Inspection and Unpacking

1.1 In This Chapter

This chapter includes:

• Unloading the system

• Inspecting the shipment

• Moving the system

• Unpacking the options

• Opening the shipping cartons

• Unpacking the cabinets

• Deskidding the cabinets

1.2 Unloading the System

Before unloading the system from the truck, deﬁne carrier and Digital Customer

Services responsibilities. Determine who is responsible for the following activities:

• Moving the system from the truck onto the loading dock

• Moving the system from the loading dock into the building

• Moving the system to the deskidding area

• Unpacking and deskidding the system

• Moving the system to the installation area

System Inspection and Unpacking 1–1

1.3 Inspecting the Shipment

To inspect the shipment, perform the steps in Table 1–1.

Table 1–1 Inspecting the Shipment

Step Action

1. Refer to the product delivery document. Make sure you received the correct

number of shipping cartons.

2. If any cabinet or option is missing or damaged, report it on the labor activity

reporting system (LARS). Include a note to clarify the extent of the problem.

Notify the customer and responsible Digital Customer Services manager.

Note

If there is a problem, stop the installation until the customer notiﬁes the

carrier or insurance company and gives you permission to continue.

1.4 Moving the Shipment

To move the shipment, perform the steps in Table 1–2.

Table 1–2 Moving the Shipment

Step Action

1. Move all shipping cartons to the installation area.

2. Make sure the installation area provides a ﬁrm surface for the system.

3. Make sure the installation area allows full exhaust airﬂow from the rear of the

cabinets.

Note

If there is a problem, stop the installation until the customer notiﬁes the

carrier or insurance company and gives you permission to continue.

1–2 System Inspection and Unpacking

Inhaltsverzeichnis

Andere Digital Equipment Desktop Handbücher

Digital Equipment

Digital Equipment PDT 11/150 Bedienungsanleitung

Digital Equipment

Digital Equipment VAX 4000 100 Service-Handbuch

Digital Equipment

Digital Equipment VAX 4000 500A Bedienungsanleitung

Digital Equipment

Digital Equipment VAX 6000 Series Bedienungsanleitung

Digital Equipment

Digital Equipment VAXstation 4000/90 Series Benutzerhandbuch

Digital Equipment

Digital Equipment VT18X Bedienungsanleitung

Digital Equipment

Digital Equipment AlphaStation 600 Series Handbuch

Digital Equipment

Digital Equipment PMS 201 Technisches Datenblatt

Digital Equipment

Digital Equipment VAX 4000 Model 100 Technische Daten

Digital Equipment

Digital Equipment DIGITAL Personal Workstation Installations- und Betriebshandbuch

Digital Equipment

Digital Equipment DECstation 5000 Kurzanleitung

Digital Equipment

Digital Equipment DEC 3000 700 AXP Kurzanleitung

Digital Equipment

Digital Equipment MicroVAX 3100 Model 85 Service-Handbuch

Digital Equipment

Digital Equipment DECstation 2100 Handbuch

Digital Equipment

Digital Equipment digital VAX 8200 Bedienungsanleitung

Digital Equipment

Digital Equipment DEC 3000 300 AXP Series Gebrauchsanweisung

Digital Equipment

Digital Equipment VAXstation 2000 Handbuch

Digital Equipment

Digital Equipment DECstation 5000/100 Series Betriebsanleitung

Digital Equipment

Digital Equipment VENTURIS 575 Bedienungsanleitung

Digital Equipment

Digital Equipment MicroVAX 3100 90 Leitfaden

Digital Equipment

Digital Equipment VAXstation 3100 Series Installations- und Betriebshandbuch

Digital Equipment

Digital Equipment DIGITAL Ultimate Workstation 533 Bedienungsanleitung

Digital Equipment

Digital Equipment VAX 4000 Model 100 Kurzanleitung

Digital Equipment

Digital Equipment VAX 4000 300 Handbuch

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung

HP Z1 Bedienungsanleitung

Everex

Everex eXplora Bedienungsanleitung