Digitus DN-80112-1 Bedienungsanleitung
16/24-Port
Gigabit Switch
Quick Installation Guide
DN-80112-1 DN-80113-1
2
1. Introduction
DN-80112-1 has 16x10/100/1000Mbps RJ45 port,
Using store and forward technology, combined with dynamic memory
allocation, to ensure the effective allocation of bandwidth to each
port. This switch is easy to install and does not require configuration，
It is easy to manage and maintain which can meet a lot of networking
environment, such as Business building, Community, Hotel, Office etc.
DN-80113-1 has 24 10/100/1000 Mbps RJ45 ports, with port 23 and port 24
as the uplink ports. It uses store-and-forward technology in combination with
the dynamic memory allocation for each port. The integrated VLAN function
can improve the network environment and reduces network maintenance
costs. The DN-80113-1 is easy to manage and maintain.
2. Main feature
Flow control for full duplex operation and back pressure for
half duplex operation
Supports VLAN mode (Only for DN-80113-1)
LED lights for monitoring the operating status and for fault analysis
Line speed forwarding, smart identification
Supports jumbo frame up to 9216K bytes
Line speed forwarding, smart identification
3. Package Content
1x 16/24 Port Switch
1x Power Cable
1x QIG
1x Mounting material
3
4. Specifications
Model DN-80112-1 DN-80113-1
Standard
IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z,
IEEE802.3az, IEEE802.3x
Network Media
10BASE-T: UTP category 3,4,5 cable (≤100m)
100BASE-TX: UTP category 5 cable (≤100m)
1000BASE-T: UTP category 5e cable (≤100m)
MAC Address Table 8K, Auto-learning, Auto-aging
Transfer mode
Store-and-Forward
Frame Forward Rate
10Base-T: 14881pps/Port
100Base-TX: 148810pps/Port
1000Base-T/X: 1488095pps/Port
Switching Capacity 32Gbps 48Gbps
Forwarding Rate 23.8Mpps 35.7Mpps
Packet buffer
4.1M bit
Dimensions (LxWxH)
280 x 180 x 44 mm
Fan
Fanless
Power Input AC: 100~240V, 50/60Hz
Temperature
Operating Temperature: 0°C ~ 40 °C (32 °F ~104°F)
Storage Temperature: -40 °C ~ 70 °C (-40 °F ~158°F)
Humidity Operating Humidity: 10% ~ 90% non-condensing
Storage Humidity: 5% ~ 90% non-condensing
Green energy saving IEEE 802.3az
MTBF >50000 hours
4
5. Hardware Description
5.1 Front Panel
The Front Panel consists of Ethernet Ports. The LED indicators are also
located on the panel.
DN-80112-1
LED indicators
16x10/100/1000Mbps port
DN-80113-1
LED indicators
DIP S
witch
24x10/100/1000Mbps port
DIP Switch (Only for DN-80113-1)
The DIP switch located on the left panel.
•Default: the factory default mode, can normal communication between
port 1~24.
•VLAN: 1-22 port can be isolated each other but 1-22 port can connect to
23-24 port after open VLAN to stop broadcast storm to increase
forwarding rate of frame.
LED indicator
LED
Color
Function
PWR Green
Off: No Power supply.
Light: Indicates the switch has power.
LNK/ACT Green
Off: No device is connected to the corresponding port.
Light: Indicates the link through that port is successfully
established at 10/100/1000Mbps.
Blink: Indicates that the Switch is actively sending or
receiving data over that port.
5
5.2 Rear Panel
The rear panel of the switch indicates an AC inlet power socket, which
accepts input power from 100 to 240V AC, 50/60HZ.
Power S
ocket
Grounding Column
Power socket
Connect the female connector of the power cord here, and the male
connector to the AC (Alternating Current) power outlet. Please make sure the
voltage of the power supply meets the requirement of the input voltage
Grounding column
The switch already comes with lightning protection mechanism. For safety
consideration, you should ground the switch through the PE (Protecting
Earth) cable by Grounding Column
6.
Installation the Switch
This part describes how to install your Ethernet Switch and make connections
to it. Please follow the following instructions in avoid of incorrect installation
causing device damage and security threat.
Before cleaning the switch, unplug the power plug of the switch first.
Do not clean the switch with wet cloth or liquid
Do not place the switch near water or any damp area. Prevent water or
moisture from entering the switch chassis
Do not place the switch on an unstable case or desk. The switch might be
damaged severely in case of a fall
Ensure proper ventilation of the equipment room and keep the ventilation
vents of the switch free of obstruction
Make sure that the operating voltage is the same one labeled
on the switch
Do not open the chassis while the switch is operating or when electrical
hazards are present to avoid electrical shocks
6
6.1 Desktop Installation
Install the Switch on a desktop, please attach these cushioning rubber feet
provided on the bottom at each corner of the Switch in case of the external
vibration. Allow adequate space for ventilation between the device and the
objects around it as example below.
7
6.2 Rack-mountable Installation
The switch is rack-mountable and can be installed on an EIA-19-inch
equipment rack. To do this, first, please install the mounting brackets on the
switch’s side panels (one on each side), secure them with the included
screws, and then use the screws provided with the equipment rack to mount
the switch on the 19-inch rack as example below.
8
7. Turn on the switch
Please connect the AC power cord into the rear of the switch and to an
electrical outlet (preferably one that is grounded). When the switch is power
on, the LED indicators flash momentarily for one second, which represents a
resetting of the system. The Power LED indicator turns on green.
Note: Please confirm the voltage is correct before power on, otherwise the
switch will be damaged.
(The power input is:100V-240Vac, 50/60Hz.)
This is a Class A product. In home environment, this product may cause radio
interference. In this case, the user may be required to take appropriate
measures.
Hereby Assmann Electronic GmbH, declares that the Declaration of
Conformity is part of the shipping content. If the Declaration of Conformity is
missing, you can request it by post under the below mentioned manufacturer
address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Digitus Schalten Handbücher
Digitus
Digitus DN-95354 Bedienungsanleitung
Digitus
Digitus DN-80063 Bedienungsanleitung
Digitus
Digitus DS-12850 Bedienungsanleitung
Digitus
Digitus DA-70248 Bedienungsanleitung
Digitus
Digitus DN-80066 Bedienungsanleitung
Digitus
Digitus DN-95341-1 Bedienungsanleitung
Digitus
Digitus DN-80233 Bedienungsanleitung
Digitus
Digitus DA-70253 Bedienungsanleitung
Digitus
Digitus DN-80111 Bedienungsanleitung
Digitus
Digitus DN-80113 Bedienungsanleitung
Digitus
Digitus DA-70244 Bedienungsanleitung
Digitus
Digitus DA-73301 Bedienungsanleitung
Digitus
Digitus DN-95316 Bedienungsanleitung
Digitus
Digitus DS-16202-1 Bedienungsanleitung
Digitus
Digitus DS-15202 Bedienungsanleitung
Digitus
Digitus DS-11200-1 Bedienungsanleitung
Digitus
Digitus Desktop 4-PortAudio-Combo-KVM Switch Bedienungsanleitung
Digitus
Digitus DS-50304 Bedienungsanleitung
Digitus
Digitus DC IC812I-MC Bedienungsanleitung
Digitus
Digitus Professional DN-60013 Bedienungsanleitung
