Dimplex DS4411 Bedienungsanleitung

7210170100r00

Valued Customer,

Thank you and congratulations for purchasing a Dimplex

electric stove. Over the years, valuable memories

will occur around the warmth and comfort of your

stove. Thank you for allowing our product to be the

backdrop for those special moments.

Serial Number

Model Number

Part Number

Quality checked by:

Owner’s Manual

Model Numbers:

DS4411

DS2205

QUICK REFERENCE GUIDE

1.PriortotherstuseoftheCompactStoveverify

the following:

Are the circuit breakers for the• unit on?

Are the light bulbs in your• Compact Stove

loose? (to check, follow the instructions

for replacing the light bulbs under the

maintenance section of this manual)

2. The heater on your Compact Stove may emit

aslight,harmlessodorwhenrstused.This

odor is a normal condition caused by the initial

heating of internal heater parts.

3. The information regarding the model of your

Compact Stove can be found on the rating plate

located on the back of the unit.

4. If you have any technical questions regarding

the operation of your Compact Stove, or require

service for your stove contact Dimplex North

America customer service at 1-888-DIMPLEX

(1-888-346-7539).

CONTENTS

PAGE 1 Important Instructions

PAGE 3 Model and Serial Number

Information

PAGE 4 Compact Stove Installation

PAGE 4 Operation

PAGE 6 Maintenance

PAGE 8 Warranty

IMPORTANT INSTRUCTIONS

Please Retain This User’s Guide For Future Reference

When using electrical appliances, basic precautions should always be followed

toreducetheriskofre,electricshock,andinjurytopersons,includingthe

following:

1. Read all instructions before using the Compact Stove.

2. The heater is hot when in use. To avoid burns, do not let bare skin touch

hot surfaces. The trim around the heater outlet becomes hot during heater

operation. Keep combustible materials, such as furniture, pillows, bedding,

papers, clothes, and curtains at least 3 feet (0.9m) from the front of the unit.

CAUTION: High Temperature. Keep electrical cords, drapery, and

other furnishings at least 3 feet (0.9m) from the front of the heater and

away from the side and rear.

3. Extreme caution is necessary when any heater is used by or near children

or invalids and whenever the unit is left operating and unattended.

4. Always unplug the Compact Stove when not in use.

5. Do not operate any unit with a damaged cord or plug, or if the heater has

malfunctioned, or if the Compact Stove has been dropped or damaged in

any manner. Return heater to authorized service facility for examination,

electricalormechanicaladjustment,orrepair.

6. Do not use outdoors.

7. The Compact Stove is not intended for use in bathrooms, laundry areas

and similar indoor locations. Never locate heater where it may fall into a

bathtub or other water container.

8. Do not run the cord under carpeting. Do not cover cord with throw rugs,

runners,orthelike.Arrangecordawayfromtrafcareaandwhereitwill

not be tripped over.

9. To disconnect the unit, turn the controls off, then remove the plug from the

outlet.

10.Donotinsertorallowforeignobjectstoenteranyventilationorexhaust

openingasthismaycauseanelectricshockorre,ordamagetothe

heater.

11.Topreventapossiblere,donotblockairintakeorexhaustinanymanner.

Do not use on soft surfaces, like a bed, where openings may become

blocked.

12. All electrical heaters have hot and arcing or sparking parts inside. Do not

useinareaswheregasoline,paint,orammableliquidsareusedorstored

orwheretheunitwillbeexposedtoammablevapors.

13. Do not modify the Compact Stove. Use it only as described in this manual.

Anyotherusenotrecommendedbythemanufacturermaycausere,

electricshockorinjurytopersons.

14. To reduce the risk of electric shock, this appliance has a polarized plug

(onebladeiswiderthantheother).Thisplugwilltinapolarizedoutlet

onlyoneway.Iftheplugdoesnottfullyintheoutlet,reversetheplug.If

itstilldoesnott,contactaqualiedelectriciantoinstalltheproperoutlet.

Do not change the plug in any way. Avoid the use of an extension cord.

Extensioncordsmayoverheatandcauseariskofre.Ifyoumustusean

extension cord, the cord must be No. 14 AWG minimum size and rated no

less than 1875 Watts.

15. Do not burn wood or other materials in the Compact Stove.

16. Do not strike the clear door panel.

17.Alwaysuseacertiedelectricianshouldnewcircuitsoroutletsberequired.

18. Always use properly grounded, fused and polarized outlets.

19. Disconnect all power supply before performing any cleaning, maintenance

or relocation of the unit.

20. When transporting or storing the unit and cord, keep in a dry place, free

from excessive vibration and store so as to avoid damage.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

SAVE THESE INSTRUCTIONS

!NOTE: Procedures and techniques that are considered important

enough to emphasize.

CAUTION: Procedures and techniques which, if not carefully

followed, will result in damage to the equipment.

WARNING: Procedures and techniques which, if not carefully

 followed,willexposetheusertotheriskofre,seriousinjury,

illness or death.

!NOTE: This equipment has been tested and found to comply with the

limits for Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

· Reorient or relocate the receiving antenna.

· Increase the separation between the equipment and the receiver.

· Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

· Consult the dealer or an experienced radio/TV technician for help.

Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynot

cause interference and; (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Model and Serial Number Information

If you have any questions about our products please have the Part,

Model and Serial numbers available upon calling Customer Service.

To locate the Part/Model and Serial numbers refer to Figure 1 below.

Record the Model Number, Serial Number, and Part number on the

front cover of this manual for future reference.

Part Number

Serial Number

Figure 1

Model Number

Compact Stove Installation

!NOTE: A 15 Amp, 120 Volt circuit is required. A dedicated circuit

is preferred but not essential in all cases. A dedicated circuit will

be required if, after installation, the circuit breaker trips or fuses

blow on a regular basis when the heater is operating. Additional

appliances on the same circuit may exceed the current rating of the

circuit breaker.

WARNING: Ensure the power cord is not installed so that it is

pinched or against a sharp edge and ensure that the power cord is

stored or secured to avoid tripping or snagging to reduce the risk of

re,electricshockorinjurytopersons.

Construction and electrical wiring must comply with local building

codesandotherapplicableregulationstoreducetheriskofre,

electricshockandinjurytopersons.

Do not attempt to wire your own new outlets or circuits. To reduce

theriskofre,electricshockorinjurytopersons,alwaysusea

licensed electrician.

1. Make sure the unit’s Main ON/OFF switch is switched OFF (refer to

operating instruction section).

2. Plug the unit into a 15 Amp/120 VAC outlet. If the cord does not

reach, you may use an extension cord rated for a minimum of 1875

Watts.

Operation

A. Main On/Off Switch

The switch has two (2) ON

positions marked with and

“Manual”. The “Manual”

position is for manual

operation. In this position the

built-in remote control is by-

passed.

The position is for operating

the unit with the provided

remote control. When in

Figure 2

position the unit is operated with the ON and OFF buttons of the

remote control.

When the switch is in the center position the unit is off.

B. Heater ON/OFF Switch

The Heater ON/OFF Switch supplies power to the heater fan and the

heater element. When the switch is in the ON position the heater

operates if the thermostat calls for heat.

C. Heater Thermostat Control

Toadjustthetemperaturetoyourindividualrequirements,turnthe

thermostat control clockwise all the way to turn on the heater. When

the room reaches the desired temperature, turn the thermostat knob

counter clockwise until you hear a click. Leave in this position to

maintain the room temperature at this setting. For additional heat, turn

clockwise until you hear the click again and the heater will turn on.

!NOTE: When the heater is switched ON, the heater fan will

operate. The heater element may or may not be on, depending on

the thermostat control setting (see “Heater Thermostat Control”).

Resetting The Temperature Cutoff Switch

The heater is protected with a safety device to prevent overheating.

Should the heater overheat, an automatic cut out will turn the heater

off and it will not come back on without being reset. It can be reset

byswitchingtheON/OFFSwitchtoOFFandwaitingve(5)minutes

before switching the unit back on.

CAUTION: If you need to continuously reset the heater, unplug

the unit and call Dimplex North America Limited at 1-888-346-7539.

Remote Operation (Figure 3)

The stove is supplied with an integrated on/off remote control.

!NOTE: Ensure that the stove’s Main ON/OFF Switch is set to the

Remote setting (right position).

To operate, push the ON button to turn stove on, push the OFF button

to turn the stove off.

Remote Control

Initialization

1. Place the Main ON/OFF

Switch (Figure 2A) in

the OFF (“ o ”) position.

2. Waitaminimumofve

(5) seconds and then

place the Main ON/OFF

Switch in the Remote

(right) position.

3. Within 10 seconds of

changing the switch position, press the ON button located on the

remote control transmitter (Figure 3). This will synchronize the

remote control transmitter and the stove receiver.

!NOTE: You will have only 10 seconds to perform this last step.

Failure to do so will result in these steps needing to be followed

again.

Battery Replacement

To replace the battery:

• Slidebatterycoveropenonthehandheldtransmitter.

• Correctlyinstallone(1)12Volt(A23)batteryinthebatteryholder.

• Closethebatterycover.

Maintenance

WARNING: Disconnect power before attempting any maintenance

orcleaningtoreducetheriskofre,electricshockordamageto

persons.

Light Bulb Replacement

Allow at least 10 minutes for light bulbs and heater to cool off before

touching bulbs to avoid accidental burning of skin.

Light bulbs need to be replaced when you notice a dark section of

Button

Battery

Cover

OFF

Button

Battery

Figure 3

theameorwhentheclarityanddetailofthelogexteriordisappears.

There are two (2) bulbs located under the log set which generate the

amesandembers.

Helpful Hints

It is a good idea to replace all light bulbs at one time if they are close to

the end of their rated life. Group replacement will reduce the number

of times you need to open the unit to replace light bulbs.

Light Bulb Requirements

Quantity of two (2) clear chandelier or candelabra bulbs with an E-12

(small) socket base, 25 Watt rating.

Required tools: Phillips screw driver.

Replacement:

1. Removethevescrews

from the access panel,

located on the back of the

unit, and remove access

panel.

2. Locate and examine the

bulb to determine if

replacement is required.

3. Unscrew the bulb counter

clockwise.

4. Insert new bulbs.

5. Secure access panel to

unit.

Clear Door Panel Cleaning

The clear door is cleaned in the factory during the assembly operation.

During shipment, installation, handling, etc., the clear door may collect

dust particles. These can be removed by dusting lightly with a clean,

dry cloth.

Toremovengerprintsorothermarks,thecleardoorscanbecleaned

with a damp cloth. The clear door should be completely dried with a

Figure 4

Light

Bulbs (2)

Access Panel

Screws

Andere Handbücher für DS4411

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dimplex Herd Handbücher

Dimplex

Dimplex Brayford BFD20 Bedienungsanleitung

Dimplex

Dimplex SNG20 Bedienungsanleitung

Dimplex

Dimplex Westcott 12kW Stove Bedienungsanleitung

Dimplex

Dimplex ELECTRALOG CS1205 Bedienungsanleitung

Dimplex

Dimplex Stockbridge 2.0 Bedienungsanleitung

Dimplex

Dimplex Bellingham BLM4iSE Bedienungsanleitung

Dimplex

Dimplex Lucia LUC20-EU Bedienungsanleitung

Dimplex

Dimplex DS2205 Bedienungsanleitung

Dimplex

Dimplex Piermont PMN20 Bedienungsanleitung

Dimplex

Dimplex ELECTRALOG CS1205 Bedienungsanleitung

Dimplex

Dimplex BFD20 Bedienungsanleitung

Dimplex

Dimplex DS4411 Bedienungsanleitung

Dimplex

Dimplex Westcott WST4i Bedienungsanleitung

Dimplex

Dimplex Opti-myst Cassington CSN20 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Dimplex

Dimplex DS6650 Bedienungsanleitung

Dimplex

Dimplex DCS19W Bedienungsanleitung

Dimplex

Dimplex CLUB Bedienungsanleitung

Dimplex

Dimplex Westcott 5 WST5SE Bedienungsanleitung

Dimplex

Dimplex DS3311 Bedienungsanleitung

Dimplex

Dimplex Brayford BFD20 Bedienungsanleitung

Dimplex

Dimplex Optiflame Electric Fireplace Bedienungsanleitung

Dimplex

Dimplex ELECTRIC STOVE Bedienungsanleitung

Dimplex

Dimplex Bellingham 8kW Bedienungsanleitung

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

Parmco

Parmco FS 600 Bedienungsanleitung

MCZ

MCZ SUITE AIR 10 M2 Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung

Regency

Regency Ultimate U39E Series Kurzanleitung