Dimplex DS7420 Kurzanleitung

PARTS AND SERVICE MANUAL

FOR THE 23” STOVE

MODEL NUMBER:

DS7420

TABLE OF CONTENTS

OPERATION PAGE1

PARTS DRAWING PAGE 3

PARTSLIST PAGE4

WIRING DIAGRAM PAGE 5

LIGHT BULB REPLACEMENT PAGE 6

MAIN ON/OFF SWITCH REPLACEMENT PAGE 8

LIGHT DIMMER SWITCH REPLACEMENT PAGE 9

FLAME MOTOR/FLAME ROD REPLACEMENT PAGE 10

HEATER ON/OFF SWITCH REPLACEMENT PAGE 11

HEATER THERMOSTAT CONTROL REPLACEMENT PAGE 12

HEATER ASSEMBLY REPLACEMENT PAGE 13

POWER CORD REPLACEMENT PAGE 14

DS7420

NOTE

A 15amp, 120 volt circuit is required. A dedicated circuit is preferred but not essential in

all cases. A dedicated circuit will be required if, after installation, the circuit breaker trips

or fuse blows on a regular basis when the heater is operating. Additional appliances on

the same circuit may exceed the current rating of the circuit breaker.

WARNING

Ensure the power cord is not installed so that it is pinched or against a sharp edge and

ensure that the power cord is stored or secured to avoid tripping or snagging to reduce

the risk of fire, electric shock or injury to persons.

Construction and electrical outlet wiring must comply with local building codes and other

applicable regulations to reduce the risk of fire, electric shock and injury to persons.

Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire,

electric shock or injury to persons, always use a licensed electrician.

STOVE INSTALLATION

1. Make sure the units MAIN ON/OFF switch is switched OFF (refer to operating

instruction section).

2. Plug the unit into a 15Amp/120volt outlet. If the cord does not reach, you may use

an extension cord rated for a minimum of 1875 watts.

OPERATION

To access the controls, go to the back of the stove.

A. MAIN POWER ON/OFF SWITCH

The main power on/off switch supplies power to all stove

functions (heater & flame).

B. TOP LIGHT ON/OFF SWITCH

Controls the light intensity of the log bed display area.

C. HEATER ON/OFF SWITCH

The heater on off switch supplies power to the heater.

D. HEATER THERMOSTAT CONTROL

To adjust the temperature to your individual requirements,

turn the thermostat control clockwise all the way to turn

on the heater. When the room reaches the desired

temperature, turn the thermostat knob counter clockwise

until you hear a click. Leave in this position to maintain

the room temperature at this setting. For additional heat,

turn clockwise until you hear the click again and the heater

will turn on.

RESETTING THE TEMPERATURE CUTOFF SWITCH

Should the heater overheat, an automatic cut out will turn the heater off and it will not

come back on without being reset. It can be reset by switching the MAIN ON/OFF

SWITCH to OFF and waiting 5 minutes before switching the unit back on.

CAUTION

If you need to continuously reset the heater, unplug the unit and call Dimplex North

America Limited at 1-800-668-6663.

FIGURE 1

DS7420

REMOTE CONTROL

The remote control has a range of approximately 50ft. (15.25m) it does not have to be

pointed at the fireplace and can pass through most obstacles (including walls). It is

supplied with one of 243 independent frequencies to prevent interference with other

units. The frequency designation is indicated on the back of the transmitter (FIGURE 3)

REMOTE CONTROL INSTALLATION

1. Plug fireplace cordset into the outlet located on the side of the receiver. (FIGURE 2)

2. Plug receiver into the wall outlet.

3. Install a 9 volt battery into the transmitter. (FIGURE 3)

NOTE

• Fireplace MAIN on/off switch must be in the

ON position prior to using the Remote Control.

• ON/OFF Remote Control may be used to

control most other electrical devices including

T.V.’s, stereos and lamps.

CAUTION

• For indoor use in dry areas only

• For use on electrical devices with 15 amp

resistive load or 1/3 HP inductive load

• 120 volt AC only

FIGURE 2

Receiver

Outlet

OPEN

Frequency

Code

Battery

Cover

FIGURE 3

DS7420

REPLACEMENT PARTS

STOVE, ELECTRIC 23"

CATALOGUE NO. DS7420

PART NO. 6900470759

MOD LEVEL: MOD. D

MADE IN: CHINA

REPLACEMENT PART REPLACEMENT PART NO.

1. LOG SET 0438200200RP

2. DOOR 0438610100RP

3. FOOT 0438680100RP

4. FLAME MOTOR 2000210200RP

5. HEATER ASSEMBLY 2200490400RP

6. THERMOSTAT 2300150100RP*

7. LOWER LIGHT HARNESS 2500280100RP

8. ON/OFF SWITCH 2800070200RP

9. HEATER ON/OFF SWITCH 2800070200RP

10.UPPER LIGHT ON/OFF SWITCH 2800070200RP

11.CORD SET 4100040300RP

12.UPPER LIGHT HARNESS 4200120400RP

13.MIRROR 5900060600RP

14.REFLECTOR ASSEMBLY 5900080600RP

15.FRONT GLASS 5900440100RP

16.CAPACITOR 2300030100RP

17.TERMINAL BLOCK 4000070100RP

18.KNOB CONTROL 8800000300RP

19.REMOTE CONTROL 6800240100RP

DS7420

WIRING DIAGRAM

DS7420

If unit was operating prior to servicing allow at least 10 minutes for light bulbs and

heating element to cool off to avoid accidental burning of skin.

Disconnect power before attempting any maintenance or cleaning to reduce the risk of

electric shock or damage to persons.

Light bulbs need to be replaced when you notice a dark section of the flame or when the

clarity and detail of the log exterior disappears. There is one bulb at the top of the

opening that illuminates the log set exterior and two bulbs under the log set which

generate the flames and embers.

It is a good idea to replace all of the light bulbs at one time if they are close to the end of

their rated life. Group replacement will reduce the number of times you need to open

the unit to replace the light bulbs.

TO REPLACE UPPER LIGHT BULB

1. Open door by pulling the handle.

2. Locate the upper bulb bracket.

3. Bend light retainer bracket down.

4. Locate and remove the light bulb.

5. Insert new bulb.

6. Bend light retainer bracket back into its original position.

7. Close the door.

UPPER LIGHT BULB REQUIREMENTS

Quantity of 1 clear chandelier or candelabra bulbs with an E-12 (small) socket base, 7

watt rating.

DS7420

If unit was operating prior to servicing allow at least 10 minutes for light bulbs and

heating element to cool off to avoid accidental burning of skin.

Disconnect power before attempting any maintenance or cleaning to reduce the risk of

electric shock or damage to persons.

Light bulbs need to be replaced when you notice a dark section of the flame or when the

clarity and detail of the log exterior disappears. There is one bulb at the top of the

opening that illuminates the log set exterior and three bulbs under the log set which

generate the flames and embers.

It is a good idea to replace all of the light bulbs at one time if they are close to the end of

their rated life. Group replacement will reduce the number of times you need to open

the unit to replace the light bulbs.

TO REPLACE LOWER LIGHT BULBS

1. Remove the stove pipe kit (if equipped).

2. Gently place stove on its back on a flat surface.

3. Remove the heater cover retaining screws located on the bottom of the stove and

lower heater and light assembly out onto the floor.

4. Remove the burnt out bulb(s) by pulling straight out of socket. If bulbs are difficult to

remove form socket move the bulb from side to side while pulling being careful not to

damage the light socket.

5. Replace the lower light bulbs.

6. Reassemble in the reverse order as above.

LOWER LIGHT BULB REQUIREMENTS

Quantity of 3 – 35 watt Halogen Quartz lamps, 120 volt, G9 base. DO NOT EXCEED

35 WATTS PER BULB

DS7420

If unit was operating prior to servicing allow at least 10 minutes for light bulbs and

heating element to cool off to avoid accidental burning of skin.

Disconnect power before attempting any maintenance or cleaning to reduce the risk of

electric shock or damage to persons.

TO REPLACE MAIN ON/OFF SWITCH

1. Remove back panel screws located along the rear of the top panel.

2. Open front door and release the Cams located in the upper corner of both side

panels.

NOTE

To release Cams ensure arrow on Cam is facing up.

3. Remove top panel.

4. Locate the main on/off switch mounted on the rear panel and disconnect the wiring

clips and connections noting their original locations.

5. Depress the retainer clips on the rear of the switch and push the switch out of the

rear cover.

6. Properly orientate the new switch and connect all of the wiring clips and

connections.

7. Reassemble in the reverse order as above.

arrow

Andere Handbücher für DS7420

Inhaltsverzeichnis

Andere Dimplex Herd Handbücher

Dimplex

Dimplex Brayford BFD20 Bedienungsanleitung

Dimplex

Dimplex Log Stove MIR40 Bedienungsanleitung

Dimplex

Dimplex Opti-V 360 Bedienungsanleitung

Dimplex

Dimplex Bellingham 5kW BLM5SE Bedienungsanleitung

Dimplex

Dimplex CS33116A Bedienungsanleitung

Dimplex

Dimplex Opti-myst Gosford Kurzanleitung

Dimplex

Dimplex Mirage MIR40 Bedienungsanleitung

Dimplex

Dimplex Optiflame Electric Fireplace Bedienungsanleitung

Dimplex

Dimplex DCS19W Bedienungsanleitung

Dimplex

Dimplex SKG20BL Bedienungsanleitung

Dimplex

Dimplex 143348BK Bedienungsanleitung

Dimplex

Dimplex DS5629 Bedienungsanleitung

Dimplex

Dimplex Delaware DWR20 Bedienungsanleitung

Dimplex

Dimplex Opti-myst Cassington CSN20 Bedienungsanleitung

Dimplex

Dimplex ELECTRALOG CS1205 Bedienungsanleitung

Dimplex

Dimplex Bayport BYP20 Bedienungsanleitung

Dimplex

Dimplex CELESTE Bedienungsanleitung

Dimplex

Dimplex BAR20-AU Bedienungsanleitung

Dimplex

Dimplex TDS8515T Bedienungsanleitung

Dimplex

Dimplex Langbrook LBK5 Bedienungsanleitung

Dimplex

Dimplex Club Courchevel CLB20E Bedienungsanleitung

Dimplex

Dimplex Willowbrook WLL20 Bedienungsanleitung

Dimplex

Dimplex Optiflame Cassia Noir RTOFSTV20 Bedienungsanleitung

Dimplex

Dimplex DS5598 Bedienungsanleitung

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

Parmco

Parmco FS 600 Bedienungsanleitung

MCZ

MCZ SUITE AIR 10 M2 Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung

Regency

Regency Ultimate U39E Series Kurzanleitung