Directed Directechs DB3 Bedienungsanleitung

INSTALLATION GUIDE

DB3

2010 Toyota Camry. 403.TL11 1.15

This product is intended for installation by a professional installer only! Attempts to install this

product by a person other than a trained professional may result in severe damage to a vehicle’s

electrical system and components.

Introduction 3

Vehicle function compatibilities 4

Pre-installation and application warnings 5

Key type 6

Wiring Diagram 7

Locating components in the vehicle 8

Vehicle connections 9

Module programming 11

With transponder and CAN 11

Without transponder with CAN 12

Connecting the module 13

LED diagnostics and troubleshooting 14

Soft reset 16

Hard reset 16

Feature programming 17

Feature and option list 18

Limited one year consumer warranty 19

Quick reference guide 20

Contents

3403.TL11 1.15 2010 Toyota Camry

Introduction

DB3 is an all-in-one door lock and override module.

Warning!

This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs

Mobile application for smartphones. Refer to “Connecting the module” for more information.

4403.TL11 1.15 2010 Toyota Camry

Vehicle function compatibilities

This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.

Arm Factory Security

Disarm Factory Security

Door Lock Control

Door Unlock

Driver Priority Unlock

Trunk / Hatch Release

Immobilizer Bypass-Data No Key Req'd

Remote Start Takeover

Tach / RPM Output

Entry Monitoring ALL Door Pins

Entry Monitoring Driver Door Pin

Entry Monitoring Hood Pin

Entry Monitoring Trunk/Hatch Pin

Factory Alarm Trigger Monitoring

Brake Status (foot brake)

E-Brake Status

Ignition Status

5403.TL11 1.15 2010 Toyota Camry

Pre-installation and application warnings

Firmware notes: This section highlights important information for this specic rmware and will assist in

pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness

compatible

Keys required for

programming 1Keys required for

operation 0

Important! TL11 requires either CAN or IMMO connections. An Analog Firmware is recommended if CAN connections are

NOT used and the vehicle does NOT have a transponder. The TL11 installation guides can be used for wire and connection

details.

Some Toyota 2010+ models have dierent encryption types. Please look at your key blade and identify the markings. A dot

"." means the vehicle is compatible with TL11 rmware. "G" or "H" indicates the vehicle is not compatible with this rmware.

Refer to "Key Types" for more information. Note: some replacement keys may not have any markings on the key.

Unless specied otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic

connector.

Refer to the "Vehicle connections" following the installation diagram.

General notes: This section highlights important information for this specic rmware.

[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.

[2] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin or

NOT supported in data.

[3] Second starter connection may be required in some vehicles.

6403.TL11 1.15 2010 Toyota Camry

Key type

Some Toyota 2010+ models have different encryption types. Please look at your key blade and identify the markings.

G-stamped keys Standard Key

H-stamped keys

For vehicles with H-stamped keys, see

the TL10 firmware.

For vehicles with G-stamped keys, see

the TL5 & TL7 firmware.

For vehicles with dot-stamped keys,

see the TL11 firmware.

Note: Some replacement keys

may not have any markings on

the key.

7403.TL11 1.15 2010 Toyota Camry

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

D2D Port

(-) Ground (-) Ground

(+) Ignition 1 Output

(+) Ignition 2 Output

(+) 12V Input

(-) Parking Lights Output

HS CAN High: Tan/Black: 3

HS CAN Low: Tan: 4

1412

10 42

9: Pink: (+) Ignition Input

Wiring diagram

(+) Starter 2 Output

(+) Accessory Output

(+) Starter 1 Output

XKD2D65

(AC) Tach Output: Violet/White: 5

TX: Yellow/Black: 10

RX: Orange/Black: 11

(AC) Tach Input

OBDII Plug

Black Connector

HS CAN High: Pin 6

HS CAN Low: Pin 14

Headlight Switch

(white conn. at headlights)

(-) Parking Lights: Pin 18

12345678910

1112131415161720

19 18

Refer to Vehicle connections for wire and connector details.

Ignition Switch

Dash Fuse Box

(white 1-pin conn.)

Transponder Key Amplifier

(black conn. around ignition)

(-) Hood Pin Input

Hood Pin

8403.TL11 1.15 2010 Toyota Camry

Locating components in the vehicle

9403.TL11 1.15 2010 Toyota Camry

Vehicle connections

The connection information listed below is specific to the 2010 Toyota Camry. Refer to “Pre-installation and application warnings” for a list of important notes.

Data 14-pin blue connector (H1)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color

H1/1 Light Green No Connection No Connection

H1/2 Violet/Yellow No Connection No Connection

H1/3 Tan/Black (DATA) HS CAN High OBD-data link connector, black 16 pin plug, pin 6 data black

H1/4 Tan (DATA) HS CAN Low OBD-data link connector, black 16 pin plug, pin 14 data white

H1/5 Orange/Green No Connection No Connection

H1/6 Orange/Brown No Connection No Connection

H1/7 Brown Relay N.O. No Connection No Connection

H1/8 Yellow Relay COM No Connection No Connection

H1/9 Orange/Yellow Relay N.C. No Connection No Connection

H1/10 Orange/Red Relay N.C. No Connection No Connection

H1/11 Yellow/Red Relay COM No Connection No Connection

H1/12 Brown/Red Relay N.O. No Connection No Connection

H1/13 Red (+) W2W Only - 12 Volt Input ignition switch, white 8 pin plug, pin 5 + black (30A)

H1/14 Black (-) W2W Only - Ground (chassis ground)

Output 12-pin red connector (H2)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color

H2/1 Black/White (-) W2W Only - E-Brake Output Remote Starter

H2/2 Green/Black No Connection No Connection

H2/3 Green/White (-) W2W Only - Door Output Remote Starter

H2/4 Red/Black (-) W2W Only - Trunk Output Remote Starter

H2/5 Violet/White (AC) W2W Only - Tach Output [1] Remote Starter

H2/6 Gray (+) W2W Only - Brake Output Remote Starter

H2/7 Gray/Black No Connection No Connection

H2/8 Violet/Green No Connection No Connection

H2/9 Violet/Brown No Connection No Connection

H2/10 Yellow/Black (Data) Immo Data Transponder Key Amplifier on ignition switch, black 7 pin plug, pin 5 data red

H2/11 Orange/Black (Data) Immo Data Transponder Key Amplifier on ignition switch, black 7 pin plug, pin 4 data brown

H2/12 Blue/Red (-) W2W Only - Hood Output Remote Starter

Input 10-pin black connector (H3)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color

10 403.TL11 1.15 2010 Toyota Camry

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color

H3/1 Green (-) W2W Only - Lock Input Remote Starter

H3/2 Blue (-) W2W Only - Unlock Input Remote Starter

H3/3 Red/White (-) W2W Only - Trunk Input Remote Starter

H3/4 White/Violet No Connection No Connection

H3/5 Violet/Black No Connection No Connection

H3/6 White/Black No Connection No Connection

H3/7 Pink/White No Connection No Connection

H3/8 Violet No Connection No Connection

H3/9 Pink (+) Ignition Input ignition switch, white 8 pin plug, pin 6 + yellow

H3/10 Blue/White (-) W2W Only - Ground When Running (Status) Input Remote Starter

D2D 4-pin white connector (H4)

Module

Conn./Pin Color Description

H4/1 Blue (Data) TX

H4/2 Black (-) Ground

H4/3 Green (Data) RX

H4/4 Red (+) 12 Volt

RF 2-pin white connector (H5)

Module

Conn./Pin Color Description

H5/1 N/A No Connection

H5/2 N/A No Connection

Additional remote start connections

(Not all of these connections may be required for your installation. Refer to the wiring diagram for vehicle-specific connections.)

Wire Connects To

Wire Location (+/-) Wire Color

12 Volts ignition switch, white 8 pin plug, pin 5 + black (30A)

Accessory ignition switch, white 8 pin plug, pin 2 + white

Ignition ignition switch, white 8 pin plug, pin 6 + yellow

Parking Lights - headlight switch, white 20 pin plug, pin 18 - black

Second Ignition ignition switch, white 8 pin plug, pin 1 + pink

Second Starter ignition switch, white 8 pin plug, pin 3 + gray

Starter ignition switch, white 8 pin plug, pin 7 + blue

Andere Handbücher für Directechs DB3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Directed Autozubehör Handbücher

Directed

Directed VOXX DEI 403.VW14 v2.11 Bedienungsanleitung

Directed

Directed 403.CHRYSLER3 Bedienungsanleitung

Directed

Directed Directechs DS3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs NISS07 Bedienungsanleitung

Directed

Directed DS4+ Bedienungsanleitung

Directed

Directed Xpresskit DBALL2 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs VW08 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed MIT4 Gebrauchs- und Pflegehandbuch

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed FORD9 Bedienungsanleitung

Directed

Directed Directechs DB3+ Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed VW10 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed 5305 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed XPRESSKIT optimax Series Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung