Directed DS3+ Bedienungsanleitung

INSTALLATION GUIDE

DS3+ / DS4+

2010 Volkswagen Jetta SportWagen. 933.VW10 2.00.195.3

This product is intended for installation by a professional installer only! Attempts to install this

product by a person other than a trained professional may result in severe damage to a vehicle’s

electrical system and components.

Introduction 3

Vehicle function compatibilities 4

Pre-installation and application warnings 5

Installation 6

Wiring diagram with T-Harness (THVWN1) 6

Wiring diagram 7

Locating components in the vehicle 8

Immobilizer interface with OEM immobilizer receiver 9

Key wrap options for THVWN1 11

Vehicle connections 12

Module programming 15

For Security-Onlyprogramming, see next section. 15

Module programming for security-only installations 16

Pairing remotes 17

Connecting the module 17

8556T Temperature Sensor 17

8504D Combo Sensor 17

RF Systems 17

When used in conjunction with SmartStart 18

D2D port configuration 18

Manual transmission 19

LED diagnostics and troubleshooting 20

Soft reset 22

Hard reset 22

Tach learning procedure (not needed with Virtual Tach) 23

Initializing Virtual Tach (not needed with hardwired or data tach applications) 23

Limited lifetime consumer warranty 24

Quick Reference Guide (customer copy) 25

Contents

3933.VW10 2.00.195.3 2010 Volkswagen Jetta SportWagen

Introduction

This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a

digital conﬁguration require the module to be ﬂashed with vehicle speciﬁc ﬁrmware. Refer to our website (www.directechs.com) and click on

the DIRECTLINK text in the header for additional information.

DS3/DS3+ and DS4/DS4+ modules provide an all-in-one solution for most modern vehicles, and include remote start, keyless entry, security,

and immobilizer bypass capabilities. T-harnesses may also be used in many applications for easy installation.

The following methods are available to conﬁgure modules:

• Web: www.directechs.com (DS3/DS3+ and DS4/DS4+)

• Desktop Application: Directlink DT (DS3/DS3+ and DS4/DS4+)

• Mobile Device: Directlink App (DS4/DS4+ only)

When Flashing via Directlink DT (Desktop app) or via the Web, an XKloader2 will be required.

To conﬁgure via Web or DirectLink DT (mobile app):

1. Disconnect the main module from any (+) 12V power source.

2. Connect the module to your computer using the XKLoader2.

3. Follow the steps in the pop-up window that will be displayed when the module is detected.

Notes:

•Flashing via web is only possible using Internet Explorer on Windows 8, 8.1, and 10.

•This method is not compatible with any other browser (Edge, Chrome, Firefox, etc.)

•When using Windows 11 or newer, Directlink DT is mandatory.

The DS4/DS4+ module is designed to be conﬁgured using the DirectLink application through mobile devices.

To download the DirectLink mobile application, visit the Google Play or Apple store. They can also be

conﬁgured via Web and DirectLink DT. The DS4/DS4+ features are built in Bluetooth® 4.0, allowing you to

conﬁgure and control your system. The DS3/DS3+ module is not equipped with Bluetooth®, therefore is not

compatible with the DirectLink app for mobile devices.

To conﬁgure via DirectLink DT (mobile app):

1. Follow and complete the wiring diagram(s) related to your installation through the app.

2. When installation is complete, select Conﬁgure DS4/DS4+.

3. Follow the on-screen instructions.

FLASH REQUIRED!

4 White

4933.VW10 2.00.195.3 2010 Volkswagen Jetta SportWagen

Vehicle function compatibilities

This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.

Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.

Parking Lights Control

Arm Factory Security

Disarm Factory Security

Door Lock Control

Door Unlock

Driver Priority Unlock

Trunk / Hatch Release

Control of aftermarket alarm with OEM remote

* Fuel Level

* Odometer

Universal RF Bypass- Key Req'd

3x LOCK START (Start control using OEM Remote)

3x LOCK STOP (Stop control using OEM Remote)

Accessory Activation

Ignition Activation

RAP Shut Down (Retained ACC Power)

Remote Start Takeover

SmartStart

Start (Crank) Activation

Tach / RPM Output

Entry Monitoring ALL Door Pins

Entry Monitoring Hood Pin

Entry Monitoring Trunk/Hatch Pin

Brake Status (foot brake)

Door Locks Status

E-Brake Status

Ignition Status

5933.VW10 2.00.195.3 2010 Volkswagen Jetta SportWagen

Pre-installation and application warnings

START HERE This section highlights important information for this speciﬁc ﬁrmware and will assist in pricing accordingly, as

well as bringing awareness to any operational or vehicle limitations.

Compatibilities and Requirements

T-Harness

compatible THVWN1 Keys required for

programming 1Keys required

for operation 1

Vehicle Takeover Refer to the Quick Reference Guide section for more details.

Firmware notes

Input/output conﬁgurations: Version 2.00 and higher use different input/output conﬁgurations and are not compatible with the

wiring instructions of previous versions. Updating an older version to version 2.00 or higher will require wiring modiﬁcations.

Note: Damage to the vehicle may occur if the appropriate wiring modiﬁcations are not done.

T-Harness (THVWN1) notes:

•All T-Harness wires not listed in the diagram are not required for the installation. Loose wires such as Siren Output and Hood

Input may need to be pulled from the tapped section of the T-Harness. Refer to the “Wiring diagram with T-Harness” for more

information on connections and installation instructions.

•The optional Plug & Play THVWN1 T-Harness is sold separately.

•OBDII Diagnostic Connector features: will remain the same even when the T-Harness is installed.

Fuses: It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each wiring

diagram.

Unless speciﬁed otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.

Refer to the "Vehicle connections" following the installation diagram.

Footnotes

[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory

hood pin, or if not supported in data.

[2] Siren: The siren is only required when enabling the security features during module ﬂashing.

[3] Key Wrap: For Key Wrap instructions, refer to "Immobilizer interface with OEM immobilizer receiver".

[4] Starter, diodes, and brake: Starter connection is mandatory. Diodes and brake connections only required on vehicles

where brake needs to be depressed to start.

[5] Security-only: For Security-Only Installations, refer to 'Locating components in the vehicle' for the optional starter

disable connection.

6933.VW10 2.00.195.3 2010 Volkswagen Jetta SportWagen

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

VESCM

Driver side underdashboard

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

22 812

4 2442

Slide to open

A module can also be used for

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

THVWN1

(optional T-Harness)

8-pin White Connector

12-pin Black Connector

22-pin White Connector

Siren

Hood Pin (-) Hood Input: Gray

(+) Siren Output: Brown/Red

Key 3

PKL 3

Key 2

Orange/Green

Orange/Brown

These connectors are not used for this installation type.

NOT USED

PTS Key 1

Ignition 2

(+) Brake Output: White

Headlight

switch

PKL 1 PKL 2

OBDII

Diagnostic Connector

42 25 1

52 41 24 11

Brown VESCM connector C

(+) Brake: Black/Red, pin 17

Steering Column Module

Wiring diagram with T-Harness (THVWN1)

Key Wrap

Parking Lights

Starter

Disable

Relay

CUT the

Dk.Blue/Black

loop to deactivate

the Starter Disable.

7933.VW10 2.00.195.3 2010 Volkswagen Jetta SportWagen

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

10 6

Key Wrap: Lt. Green: 8

Key Wrap: Lt. Green/White: 9

(-) Ground: Black: 10

HS CAN 1 Low: Tan: 1

(+) Starter / Brake Activation Output: White: 7

(+) Ignition Output: Violet/Black: 8

HS CAN 1 High: Tan/Black: 2

FT CAN High: Orange/Green: 4

FT CAN Low: Orange/Brown: 3

Siren

Hood Pin

(+) 12V Input: Red: 6 & 12

Key Wrap: Lt.Green/Red: 7

(-) Hood Input: Gray: 21

(+) Siren Output: Brown/Red: 11

HS CAN High: Orange/Black, pin 6

HS CAN Low: Orange/Brown, pin 14

Parking Lights Interrupt:

Red/White, pin 8

(+) Parking Lights: White/Black, pin 1

CUT

42 25 1

52 41 24 11

Brown VESCM connector C

(+) Brake: Black/Red, pin 17

(+) 12V:

Red/Yellow, pin 42

Diode 1A

Headlight switch

(black conn. at

light switch)

FT CAN Low: Orange/Brown, pin 15

(+) Ignition: Black, pin 17

(+) Starter:

Red/Black or

Red/Brown, pin 18

FT CAN High: Orange/Green, pin 14

VESCM-Driver side underdashboard

Parking Light Interrupt (conn. side): Blue/White: 1

(+) Parking Light Output: Blue/Red: 2

Parking Light Interrupt (vehicle side): Blue: 3

Diagnostic

Connector

OBDII

Refer to the

Optional starter disable

connection section for relay

and connection details.

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

(-) GWA Output: Dk.Blue/Black: 9

22 812

4 2442

Slide to open

A module can also be used for

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

Steering

Column Module

(behind steering

column trim)

Wiring diagram

8933.VW10 2.00.195.3 2010 Volkswagen Jetta SportWagen

Locating components in the vehicle

Optional starter disable connection

When using an external relay, use a 1N4002 diode or larger.

Note: This connection is not required when using a THVWN1 T-Harness.

22 812

4 2442

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

(-) Ground When Armed (GWA) Output: Blue/White: 2

86 85

87a

Cut

Starter (conn. side)

Starter (veh. side)

(+) Ignition

Refer to the

Vehicle connections

section for wire and

connector details.

1A diode [1N4002+ ]

Important: When ﬂashing your module for Security Only, the Ground When Armed (GWA)

function is pre-conﬁgured. When ﬂashing your module for Remote Start & Security, you must

manually assign the designated output to Anti Grind (AG) Starter Kill. (Applicable to CORE 194+.)

9933.VW10 2.00.195.3 2010 Volkswagen Jetta SportWagen

Immobilizer interface

For vehicles with Keyless Entry you must remove battery from OEM key (the OEM remote may differ from the models shown in

the illustrations).

Method 1: Key Wrap

Note:

- Make 4-6 loops and place them as close to the front of key port (OEM Immobilizer Receiver) as possible.

- Test and secure mounted loops before reassembling the vehicle.

- Make 4-6 loops and place them around the front of the plastic body of the vehicle’s coded key as shown above.

* When possible use valet key for key wrap, if blade key is used, battery must be removed.

4-6 loops

OEM

Immobilizer

Receiver

COM Relay 2: Lt. Green 8

NO Relay 2: Lt. Green/Red: 7

22 812

4 2442

556UXL is sold SEPARATELY.

Method 2: Immobilizer interface using 556UXL

IMPORTANT!: Not all OEM remotes can be inserted in 556UXL because of their size.

Make sure the key will fit, otherwise it is recommended to use a different method.

Move 556UXL loop as close to the

front of ignition cylinder (OEM

Immobilizer Receiver) as possible.

Test and secure mounted loop

before reassembling the vehicle.

COM Relay 2: Lt. Green: 8

N.O. Relay 2: Lt. Green/Red: 7

4 2442

22 810 12

Note: The discontinued 556U or 556UW can

still be used for the installation.

OEM

Immobilizer

Receiver

N/A: Green, pin 6

Black/White - NOT USED

Black/Red

Black

N/A: Violet, pin 5

N/A: Pink, pin 3

(-) GWR: Blue, pin 2

(+)12V : Red, pin 1 (+)12V

(-) Ground: Black, pin 4

10 933.VW10 2.00.195.3 2010 Volkswagen Jetta SportWagen

Method 3: Immobilizer interface with OEM Immobilizer Receiver

Immobilizer ECU

Remove battery

from OEM

Remote Control

OEM

Immobilizer

Receiver

4-6 loops

- Make 4-6 loops and place them around the front of the plastic body of the vehicle's coded key as shown above.

- Test and secure mounted loops before reassembling the vehicle.

- Make connections to the OEM Immobilizer receiver as shown above.

* When possible use valet key for key wrap, if blade key is used, battery must be removed.

COM Relay 2: Lt.Green: 8

NC Relay 2: Lt.Green/White: 9

22 812

4 2442

NO Relay 2: Lt.Green/Red: 7

22 812

4 2442

Andere Handbücher für DS3+

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Directed Autozubehör Handbücher

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed XPRESSKIT optimax Series Bedienungsanleitung

Directed

Directed 933.TL7 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed 403.SUBARU2 Bedienungsanleitung

Directed

Directed 403.SUBARU11 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs MIT2 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed DIRECTECHS CHRYSLER3 Bedienungsanleitung

Directed

Directed Directechs HYUNDAI1 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed MIT4 Gebrauchs- und Pflegehandbuch

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed FORD12 Bedienungsanleitung

Directed

Directed Directechs DS3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs DB3+ Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed 933.SUBARU2 Bedienungsanleitung

Directed

Directed DS4+ Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung