Directed DS3+ Bedienungsanleitung
Designed by Installers for Installers
INSTALLATION GUIDE
DS3+ / DS4+
2019 Audi Q8 (Smart Key). 933.VW08 1.39.195.3
© 2021 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.
Introduction 3
Vehicle function compatibilities 3
Pre-installation and application warnings 4
Wiring diagram 4
Locating components in the vehicle 6
Immobilizer interface with OEM immobilizer receiver 7
Vehicle connections 8
Connecting the module 11
Important! 11
8556T Temperature Sensor 11
8504D Combo Sensor 11
RF Systems 12
When used in conjunction with SmartStart 12
D2D port configuration 12
Manual transmission 13
Module programming 14
(For security-only programming, see next section.) 14
Module programming for security-only installations 15
LED diagnostics and troubleshooting 16
Soft reset 18
Hard reset 18
Learning the Tach (not needed with Virtual Tach) 19
Initializing Virtual Tach (not needed with hardwired or data tach applications) 19
Limited lifetime consumer warranty 20
Quick reference guide 21
Contents
3933.VW08 1.39.195.3 2019 Audi Q8 (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Introduction
DS3+ is a complete solution for remote start, security (when security features are enabled) and bypass. This guide provides
information on the installation of the module as a digital solution. Please refer to www.directechs.com for more information about
which configuration is best for your application.
Warning! This module can be configured using the web tool located at www.directechs.com. The DS3/DS3+ module is not
equipped with Bluetooth, therefore the blue LED will not flash during module programming or when performing a soft or hard reset.
DS4+ is a complete solution for remote start, security (when security features are enabled), bypass, and features
built in Bluetooth 4.0 allowing you to configure and control your system. This guide provides information on the
installation of the module as a digital solution. Please refer to the DirectLink application or www.directechs.com
for more information about which configuration is best for your application.
Warning! This module is designed to be configured using the DirectLink application for mobile devices,
however it can also be configured using the web tool located at www.directechs.com. To download the DirectLink mobile
application, please visit the Google Play or Apple store.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.
Heated Seats Activation
Rear Window Defogger Activation
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Trunk / Hatch Release
Control of aftermarket alarm with OEM remote
* Fuel Level
* Odometer
3x LOCK START (Start control using OEM Remote)
3x LOCK STOP (Stop control using OEM Remote)
Accessory Activation
Ignition Activation
RAP Shut Down (Retained ACC Power)
Remote Start Takeover
SmartStart
Start (Crank) Activation
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Brake Status (foot brake)
Door Locks Status
E-Brake Status
Ignition Status
4933.VW08 1.39.195.3 2019 Audi Q8 (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in pricing
accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible
Keys
required for
programming
1Keys required
for operation 1
This firmware does not support transponder override. One (1) programmed OEM key must be wired into the vehicle to complete the
installation of a remote starter.
The hazards lights will flash if alarm is triggered or if Car Finder is activated. Also, they will flash every 5 seconds during runtime;
however, they are not supported for the diagnostics lights.
A Note Regarding Climate Controls: Audi climate controls are key memory sensitive. This means that the last key used to operate
the vehicle will determine the setting for the climate controls. In order to make changes to environment control settings, the following
procedure is necessary:
1) Remote start the vehicle.
2) Make your climate control adjustments, ensuring NOT to use the AUTO mode on the control panel as this makes the Audi adjust
its HVAC settings based on external factors such as engine temperature.
3) When the adjustments are complete, turn off the vehicle starter, either by remote or footbrake.
To remote start the engine, the hood, the hatch and all doors must be closed.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each wiring
diagram.
Refer to the "Vehicle connections" following the installation diagram.
General notes: This section highlights important information for this specific firmware.
[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin or if NOT
supported in Data.
[2] The siren is ONLY required when enabling the security features during module flashing.
[3] For Key Wrap instructions refer to "Immobilizer interface with OEM immobilizer receiver".
[4] The correct brake activation wire will test as 0.6V with the ignition ON and 12V with the brake pedal depressed with ignition ON.
Failure to identify the correct wire will cause permanent damage to the interface.
[5] For Security Only Installations, refer to 'Locating components in the vehicle' for the optional starter disable connection.
5933.VW08 1.39.195.3 2019 Audi Q8 (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Key Wrap: Lt. Green: 8
Key Wrap: Lt. Green/Red: 7
Key Wrap: Lt. Green/White: 9
(-) Ground: Black: 10
HS CAN 1 Low: Tan: 1
(+) Brake Activation Output: White: 7
(-) GWA Output: Blue/White: 2
HS CAN 1 High: Tan/Black: 2
HS CAN 3 High: Orange/Green: 4
HS CAN 3 Low: Orange/Brown: 3
Siren
Hood Pin
(+) 12V Input: Red: 6 & 12
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
16
8
9
1OBDII
Diagnostic
Connector
HS CAN 1 Low: Violet/Brown,pin 14
HS CAN 1 High: Blue/Green, pin 6
(-) Ground: Brown/Black, pin 4
Wiring diagram
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
(-) Push-to-Start 1 Output: Lt. Blue/Black: 10
(-) Push-to-Start 2 Output: Dk. Blue/Black: 9
(-) Push-to-Start 3 Output: Lt. Green/Black: 1
22 812
4 2442
Slide to open
A module can also be used for
this installation.
IMPORTANT:
Position the
fuses correctly!
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
Refer to the
Optional starter disable
connection section for relay
and connection details.
See Vehicle
connections for
more information.
Remove the
cloth tape
for the twisted
Yellow and White
Immo. wires.
See Vehicle
connections for
more information.
Immo.
14
7
13
6
12
5
11
4
10
3
9
2
8
1
15
16
17
Black Connector
(rear of center console)
(-) PTS 6:
Blue/Yellow,
pin 3
(-) PTS 5: White/Gray, pin 2
(-) PTS 4: Yellow/Gray, pin 1
(+) 12V: Red, pin 16
Twisted pair
(in driver kick, door harness)
Alternative: HS CAN 3 wires
HS CAN 3 High: Green
HS CAN 3 Low: Orange/Brown
(+) Brake
Black/Red wire
in driver’s firewall
harness.
6933.VW08 1.39.195.3 2019 Audi Q8 (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Locating components in the vehicle
(-) Ground When Armed (GWA) Output: Blue/White: 2
86 85
30
87a
87
Optional starter disable connection
Cut
Starter (conn. side)
Starter (veh. side)
(+) Ignition
Refer to the
Vehicle connections
section for wire and
connector details.
22 812
4 2442
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
1A diode [1N4002+]
When using an external relay, use a 1N4002 diode or larger.
Important: When flashing your module for Security Only, the Ground When Armed (GWA)
function is pre-configured. When flashing your module for Remote Start & Security, you must
manually assign the designated output to Anti Grind (AG) Starter Kill.
(Applicable to CORE 194+.)
7933.VW08 1.39.195.3 2019 Audi Q8 (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Method 1: Key Wrap for Push-to-Start (PTS)
Remove battery
from OEM
Remote Control
4-6 loops
- Make 4-6 loops and place them as close to the front of key port (OEM Immobilizer Receiver) as possible.
- Test and secure mounted loops before reassembling the vehicle.
- Make 4-6 loops and place them around the front of the plastic body of the vehicle’s coded key as shown above.
- When possible use valet key for key wrap: battery must be removed.
COM Relay 2: Lt. Green: 8
NO Relay 2: Lt. Green/Red: 7
4-6
loops
OEM
Immobilizer
Receiver
22 812
4 2442
Immobilizer interface
For vehicles with Keyless Entry you must remove battery from OEM key (the OEM remote may differ from
the models shown in the illustrations).
Method 2: Key Wrap for Push-to-Start (PTS)
COM Relay 2: Lt. Green: 8
NO Relay 2: Lt. Green/Red: 7
NC Relay 2: Lt. Green/White: 9
Immobilizer ECU
Remove battery from
OEM Remote Control
4-6 loops
- Make connections to the OEM Immobilizer Receiver as shown above.
- Test and secure mounted loops before reassembling the vehicle.
- Make 4-6 loops and place them around the front of the plastic body of the vehicle’s coded key as shown above.
Cut
OEM
Immobilizer
Receiver
OEM Transponder coil:
Yellow, pin 2
22 812
4 2442
8933.VW08 1.39.195.3 2019 Audi Q8 (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2019 Audi Q8 (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes.
Data harness, 8-pin white connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H1/1 Tan (Data) HS CAN 1 Low OBD-Data Link Connector, black 16 pin plug, pin 14 Data Violet/Brown Mandatory
H1/2 Tan/Black (Data) HS CAN 1 High OBD-Data Link Connector, black 16 pin plug, pin 6 Data Blue/Green Mandatory
H1/3 Orange/Brown (Data) HS CAN 3 Low Driver Kick, door harness Data Orange/Brown Mandatory
H1/4 Orange/Green (Data) HS CAN 3 High Driver Kick, door harness Data Green Mandatory
H1/5 Lt. Green No Connection No Connection
H1/6 Violet/Brown No Connection No Connection
H1/7 Orange/Black No Connection No Connection
H1/8 Yellow/Black No Connection No Connection
Analog input/output harness, 22-pin white connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/1 Lt. Green/Black (-) PTS 3 Output Rear of Center Console, black 17 pin plug, pin 3 - Blue/Yellow (PTS 3
alternate)
Remote Start
Only
H2/2 Blue/White (-) Ground When Armed (GWA) Output [6] Starter:
Starter Relay in engine compartment passenger side rear
Ignition:
VESCM above driver kick, middle black 73 pin plug, pin 19
Must use a relay.
+
+
Red/Black
Black
Remote Start
Only
H2/3 Dk. Green/Black No Connection No Connection
H2/4 Red/White No Connection No Connection
H2/5 Brown/Black (-) Horn Output VESCM above driver kick, right black-white 73 pin plug, pin 5 Revers
e
Violet/Red Optional
H2/6 Brown/White No Connection No Connection
H2/7 White (+) (+) Brake Output [5] Driver Firewall, harness to engine compartment + Black/Red (alternate
location)
Remote Start
Only
H2/8 Violet/Black No Connection No Connection
H2/9 Dk. Blue/Black (-) PTS 2 Output Rear of Center Console, black 17 pin plug, pin 2 - White/Gray (PTS 2
alternate)
Remote Start
Only
H2/10 Lt. Blue/Black (-) PTS 1 Output Rear of Center Console, black 17 pin plug, pin 1 - Yellow/Gray (PTS 1
alternate)
Remote Start
Only
H2/11 Brown/Red (+) Siren Output [2] Security Only
H2/12 Pink No Connection No Connection
H2/13 Violet No Connection No Connection
H2/14 Brown No Connection No Connection
H2/15 White/Blue No Connection No Connection
H2/16 Red/Blue No Connection No Connection
9933.VW08 1.39.195.3 2019 Audi Q8 (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/17 Black/White No Connection No Connection
H2/18 Orange/Black No Connection No Connection
H2/19 Blue No Connection No Connection
H2/20 Green No Connection No Connection
H2/21 Gray (-) Hood Switch Input [1]
H2/22 Violet/White No Connection No Connection
Main harness, 12-pin black connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H3/1 Blue/White Relay N.C. No Connection No Connection
H3/2 Blue/Red Relay N.O. No Connection No Connection
H3/3 Blue Relay COM. No Connection No Connection
H3/4 White/Brown Relay N.C. No Connection No Connection
H3/5 White Relay COM. No Connection No Connection
H3/6 Red (+) 12 Volt Input OBD-Data Link Connector, black 16 pin plug, pin 16 + Red (10A) Mandatory
H3/7 Lt. Green/Red Relay N.O. Key Wrap [3] Rear of Center Console, twisted pair wires RF Yellow (alternate location) Remote Start
Only
H3/8 Lt. Green Relay COM. Key Wrap [3] Rear of Center Console, twisted pair wires RF Yellow (alternate location) Remote Start
Only
H3/9 Lt. Green/White Relay N.C. Key Wrap [3] Rear of Center Console, twisted pair wires RF Yellow (alternate location) Remote Start
Only
H3/10 Black (-) Ground OBD-Data Link Connector, black 16 pin plug, pin 4 - Brown/Black Mandatory
H3/11 White Relay COM. No Connection No Connection
H3/12 Red (+) 12 Volt Input OBD-Data Link Connector, black 16 pin plug, pin 16 + Red (10A) Mandatory
Relay harness, 10-pin white connector (H4)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H4/1 N/A No Connection No Connection
H4/2 Red/Black No Connection No Connection
H4/3 Pink/Black No Connection No Connection
H4/4 Pink/White No Connection No Connection
H4/5 Red No Connection No Connection
H4/6 Green No Connection No Connection
H4/7 Violet No Connection No Connection
H4/8 Orange No Connection No Connection
H4/9 Red/White No Connection No Connection
H4/10 Pink No Connection No Connection
10 933.VW08 1.39.195.3 2019 Audi Q8 (Smart Key)
©2021 VOXX•DEI LLC. All rights reserved.
RF Port harness, 2-pin white connector (H5)
Module
Conn./Pin Color Description
H5/1 N/A RF Loop
H5/2 N/A RF Loop
D2D harness, 4-pin white (1) and black (2) connectors (H6)
Module
Conn./Pin Color Description
H6/1 Blue (Data) TX
H6/2 Black (-) Ground
H6/3 Green (Data) RX
H6/4 Red (+) 12 Volt
Temperature sensor harness, 2-pin black connector (H7)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H7/1 Black Temperature Sensor
H7/2 Black Temperature Sensor
Andere Handbücher für DS3+
19
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Directed Autozubehör Handbücher
Directed
Directed DB3 403.KIA8 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed DIRECTECHS CHRYSLER8 Bedienungsanleitung
Directed
Directed VOXX DEI DS3+ Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed 403.MIT3 Bedienungsanleitung
Directed
Directed XPRESSKIT solex DLCH-CHDL6+ Bedienungsanleitung
Directed
Directed 403.VW10 Bedienungsanleitung
Directed
Directed 403.GM9 Bedienungsanleitung
Directed
Directed 933.SUBARU5 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed DS3+ Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed 933.TL7 Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
Directed
Directed Xpresskit DBALL-NISS08EU Bedienungsanleitung
Directed
Directed Directechs DB3 Bedienungsanleitung
