Directed DS3+ Bedienungsanleitung

Functions compatible with the 2013 Ford Fusion

*Telematics features: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart Pro.

* Odometer

3x LOCK START (Start control using OEM Remote)

3x LOCK STOP (Stop control using OEM Remote)

Accessory Activation

Brake Status (foot brake)

Control of aftermarket alarm with OEM remote

Door Lock Control

Door Unlock

Entry Monitoring ALL Door Pins

Entry Monitoring Hood Pin

Entry Monitoring Trunk/Hatch Pin

Factory Alarm Trigger Monitoring

Fuel level/EV battery level

Ignition Activation

Ignition Status

Immobilizer Bypass-Data No Key Req'd

Parking Lights Control

Remote Start Takeover

SmartStart

Start (Crank) Activation

Tach / RPM Output

933.FORD11

v2.07.198.12

2013 Ford Fusion

THFON2 Compatible

(Sold Separately)

Introduction 3

Pre-installation and application warnings 4

Installation 5

Wiring diagram with OEM Remote Start and with T-Harness (THFON2 Rev. 2) 5

Wiring diagram without OEM Remote Start with T-Harness (THFON2 Rev. 2) 6

Wiring diagram with OEM Remote Start and with T-Harness (THFON2 Rev. 1) 7

Wiring diagram without OEM Remote Start with T-Harness (THFON2 Rev. 1) 8

Wiring diagram with OEM Remote Start without T-Harness 9

Wiring diagram without OEM Remote Start without T-Harness 10

Locating components in the vehicle 11

Vehicle connections 12

Module programming 15

Key type vehicles 15

Module programming for convenience only (skip transponder) 16

Module programming for security-only installations 17

Pairing remotes 18

Connecting the module 19

8556T Temperature Sensor 19

8504D Combo Sensor 19

RF Systems 19

When used in conjunction with SmartStart 19

D2D port configuration 19

Manual transmission 20

LED diagnostics and troubleshooting 21

Soft reset 23

Hard reset 23

Tach learning procedure (not needed with Virtual Tach) 24

Initializing Virtual Tach (not needed with hardwired or data tach applications) 24

Limited lifetime consumer warranty 25

Quick reference guide 26

Contents

3933.FORD11 2.07.198.12 2013 Ford Fusion

Introduction

This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a

digital conﬁguration requires the module to be ﬂashed with vehicle-speciﬁc ﬁrmware. Refer to our website (www.directechs.com) and click

on the DIRECTLINK text in the header for additional information.

DS3/DS3+ and DS4/DS4+ modules provide an all-in-one solution for most modern vehicles, and include remote start, keyless entry, security,

and immobilizer bypass capabilities. T-harnesses may also be used in many applications for easy installation.

The following methods are available to conﬁgure modules:

• Web: www.directechs.com (DS3/DS3+ and DS4/DS4+)

• Desktop application: Directlink DT (DS3/DS3+ and DS4/DS4+)

• Mobile device: Directlink App (DS4/DS4+ only)

When ﬂashing via Directlink DT (desktop app) or via the Web, an XKloader2 will be required.

To conﬁgure via Web or DirectLink DT (desktop app):

1. Disconnect the main module from any (+) 12V power source.

2. Connect the module to your computer using the XKLoader2.

3. Follow the steps in the pop-up window that will be displayed when the module is detected.

Notes:

•Flashing via web is only possible using Internet Explorer on Windows 8, 8.1, and 10.

•This method is not compatible with any other browser (Edge, Chrome, Firefox, etc.).

•When using Windows 11 or newer, Directlink DT is mandatory.

The DS4/DS4+ module is designed to be conﬁgured using the DirectLink application through mobile devices.

To download the DirectLink mobile application, visit the Google Play or Apple store. They can also be

conﬁgured via Web and DirectLink DT. The DS4/DS4+ features are built in Bluetooth® 4.0, allowing you to

conﬁgure and control your system. The DS3/DS3+ module is not equipped with Bluetooth®, therefore is not

compatible with the DirectLink app for mobile devices.

To conﬁgure via DirectLink mobile app (Android/iOS):

1. Follow and complete the wiring diagram(s) related to your installation through the app.

2. When installation is complete, select Conﬁgure DS4/DS4+.

3. Follow the on-screen instructions.

FLASH REQUIRED!

4 White

4933.FORD11 2.07.198.12 2013 Ford Fusion

Pre-installation and application warnings

START HERE This section highlights important information for this speciﬁc ﬁrmware and will assist in pricing accordingly, as

well as bringing awareness to any operational or vehicle limitations.

Compatibilities and Requirements

T-Harness

compatible THFON2

AUX

or Keys required for

programming 1Keys required

for operation 0

Vehicle Takeover Refer to the Quick Reference Guide section for more details.

Firmware notes

Pit Stop/idle mode: This feature is not available in this ﬁrmware.

The following remote start features can be conﬁgured via the information display:

Climate control

Heated seats/steering wheel

Runtime (For best results, program the runtime to match the OEM setting.)

Remote start enable/disable

The optional Plug & Play THFON2 T-Harness is sold separately

Loose wires: All T-Harness wires not listed in the diagram are not required for the installation. Loose wires such as Siren Output and

Hood Input may need to be pulled from the tapped section of the T-harness. Refer to the "wiring diagram with T-Harness" for more

information on connections and installation instructions.

The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed.

All connectors are displayed from the wire side (unless speciﬁed otherwise).

Fuses positioning: It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed

on each wiring diagram.

Refer to the "Vehicle connections" following the installation diagram.

Conditions and Limitations

This installation enables the OEM remote starter and the remote start system will not work in the following conditions:

The ignition is on.

The alarm system is triggered.

The hood is open.

The transmission is not in Park (P).

The vehicle battery voltage is too low.

The service engine light is on.

Footnotes

[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin or if

not supported in data.

[2] Siren: The siren is only required when enabling the security features during module ﬂashing.

[3] Security-Only: Refer to the "Locating components in the vehicle" section for optional starter disable connection information.

5933.FORD11 2.07.198.12 2013 Ford Fusion

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

Gateway Module

(black connector on OBDII connector)

Type 2

4-pin Connectors

Type 1

NOT USED

Siren

Hood Pin

(-) Hood Input: Gray: 21

(+) Siren Output: Brown/Red: 11

(-) Trunk Release:

Gray/Yellow, pin 6

Trunk Release

(black or brown connector

at trunk release switch)

1 2 3

4 5 6

(-) Trunk Release Output: Red/White: 4

Wiring diagram with OEM Remote Start with T-Harness (THFON2 Rev. 2)

THFON2 Rev. 2 (Optional T-Harness)

Refer to the optional starter

disable connection section for

relay and connection details.

(-) Ground When Armed (GWA) Output: Blue/White: 2

Headlight Switch

8-pin White Connector

12-pin Black Connector

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

22 812

4 2442

Slide to open

A module can also be used for

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

6933.FORD11 2.07.198.12 2013 Ford Fusion

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

Gateway Module

(black connector on OBDII connector)

Type 1

4-pin Connectors

Type 2

NOT USED

Siren

Hood Pin

(-) Hood Input: Gray: 21

(+) Siren Output: Brown/Red: 11

(-) Trunk Release:

Gray/Yellow, pin 6

Trunk Release

(black or brown connector

at trunk release switch)

1 2 3

4 5 6

(-) Trunk Release Output: Red/White: 4

Wiring diagram without OEM Remote Start with T-Harness (THFON2 Rev. 2)

Refer to the optional starter

disable connection section for

relay and connection details.

(-) Ground When Armed (GWA) Output: Blue/White: 2

THFON2 Rev. 2 (Optional T-Harness)

Headlight Switch

8-pin White Connector

12-pin Black Connector

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

22 812

4 2442

Slide to open

A module can also be used for

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

7933.FORD11 2.07.198.12 2013 Ford Fusion

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

Gateway Module

(black connector on OBDII connector)

Type 2

4-pin Connectors

Type 1

NOT USED

Parking Lights Interrupt

(vehicle side: Lt. Green

Parking Lights Interrupt

(connector side): Lt. Green/White

(-) Parking Light Output:

Lt.Green/Red

Siren

Hood Pin

(-) Hood Input: Gray: 21

(+) Siren Output: Brown/Red: 11

Cut

Headlight Switch

(black connector at headlight switch)

(-) Parking Lights:

Gray or Yellow, pin 11

(-) Trunk Release:

Gray/Yellow, pin 6

Trunk Release

(black or brown connector

at trunk release switch)

1 2 3

4 5 6

Parking Light Interrupt:

Black/Blue, pin 4

(-) Trunk Release Output: Red/White: 4

Wiring diagram with OEM Remote Start with T-Harness (THFON2 Rev. 1)

THFON2 Rev. 1 (Optional T-Harness)

Refer to the optional starter

disable connection section for

relay and connection details.

(-) Ground When Armed (GWA) Output: Blue/White: 2

8-pin White Connector

12-pin Black Connector

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

22 812

4 2442

Slide to open

A module can also be used for

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

8933.FORD11 2.07.198.12 2013 Ford Fusion

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

Gateway Module

(black connector on OBDII connector)

Type 1

4-pin Connectors

Type 2

NOT USED

Parking Lights Interrupt

(vehicle side: Lt. Green

Parking Lights Interrupt

(connector side): Lt. Green/White

(-) Parking Light Output:

Lt.Green/Red

Siren

Hood Pin

(-) Hood Input: Gray: 21

(+) Siren Output: Brown/Red: 11

Cut

Headlight Switch

(black connector at headlight switch)

(-) Parking Lights:

Gray or Yellow, pin 11

(-) Trunk Release:

Gray/Yellow, pin 6

Trunk Release

(black or brown connector

at trunk release switch)

1 2 3

4 5 6

Parking Light Interrupt:

Black/Blue, pin 4

(-) Trunk Release Output: Red/White: 4

Wiring diagram without OEM Remote Start with T-Harness (THFON2 Rev. 1)

THFON2 Rev. 1 (Optional T-Harness)

Refer to the optional starter

disable connection section for

relay and connection details.

(-) Ground When Armed (GWA) Output: Blue/White: 2

8-pin White Connector

12-pin Black Connector

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

22 812

4 2442

Slide to open

A module can also be used for

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

9933.FORD11 2.07.198.12 2013 Ford Fusion

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

Parking Lights Interrupt (vehicle side: Lt. Green: 8

Parking Lights Interrupt (connector side): Lt. Green/White: 9

(-) Ground: Black: 10

(-) Parking Light Output: Lt.Green/Red: 7

HS CAN 2 Low: Tan: 1

(-) Trunk Release Output: Red/White: 4

HS CAN 2 High: Tan/Black: 2

HS CAN 1 High: Orange/Green: 4

HS CAN 1 Low: Orange/Brown: 3

Siren

Hood Pin

(+) 12V Input: Red: 6 & 12

(-) Hood Input: Gray: 21

(+) Siren Output: Brown/Red: 11

Wiring diagram with OEM Remote Start without T-Harness

Cut

MS CAN Low: Violet/Orange or Violet, pin 22

MS CAN High: Gray/Orange or Gray, pin 23

HS CAN Low:

White, pin 19

HS CAN High:

White/Blue or Blue, pin 20

(+)12V: Gray/Red, pin 24

(-) Ground:

Black/Blue, pin 14

Gateway Module

(black connector on OBDII connector)

Headlight Switch

(black connector

at headlight switch)

(-) Parking Lights:

Gray or Yellow,

pin 11

(-) Trunk Release:

Gray/Yellow, pin 6

Trunk Release

(black or brown connector

at trunk release switch)

1 2 3

4 5 6

Parking Light Interrupt:

Black/Blue, pin 4

Refer to the optional starter

disable connection section for

relay and connection details.

(-) Ground When Armed (GWA) Output: Blue/White: 2

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

22 812

4 2442

Slide to open

A module can also be used for

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

10 933.FORD11 2.07.198.12 2013 Ford Fusion

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).

Parking Lights Interrupt (vehicle side: Lt. Green: 8

Parking Lights Interrupt (connector side): Lt. Green/White: 9

(-) Ground: Black: 10

(-) Parking Light Output: Lt.Green/Red: 7

HS CAN 3 Low: Tan: 1

(-) Trunk Release Output: Red/White: 4

HS CAN 3 High: Tan/Black: 2

HS CAN 1 High: Orange/Green: 4

HS CAN 1 Low: Orange/Brown: 3

Siren

Hood Pin

(+) 12V Input: Red: 6 & 12

(-) Hood Input: Gray: 21

(+) Siren Output: Brown/Red: 11

Cut

Headlight Switch

(black connector

at headlight switch

(-) Parking Lights:

Gray or Yellow,

pin 11

(-) Trunk Release:

Gray/Yellow, pin 6

Trunk Release

(black or brown connector

at trunk release switch)

1 2 3

4 5 6

Parking Light Interrupt:

Black/Blue, pin 4

HS CAN 1 Low: White, pin 19

HS CAN 1 High: White/Blue or Blue, pin 20HS CAN 2 Low: Gray, pin 17

HS CAN 2 High: Green, pin 18

(+)12V: Gray/Red, pin 24

(-) Ground: Black/Blue, pin14

Gateway Module

(black connector on OBDII connector)

Wiring diagram without OEM Remote Start without T-Harness

Refer to the optional starter

disable connection section for

relay and connection details.

(-) Ground When Armed (GWA) Output: Blue/White: 2

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

22 812

4 2442

Slide to open

A module can also be used for

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

Andere Handbücher für DS3+

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Directed Autozubehör Handbücher

Directed

Directed DS3+ Bedienungsanleitung

Directed

Directed DIRECTWIRE DIRECTECHS 933.TL14 Bedienungsanleitung

Directed

Directed DIRECTECHS TL11 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed 403.SUBARU2 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed 403.SUBARU1 Bedienungsanleitung

Directed

Directed VOXX DEI 403.VW14 v2.11 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed DS4+ Bedienungsanleitung

Directed

Directed 403.CHRYSLER3 Bedienungsanleitung

Directed

Directed 403.NISS4HT 2.36 RSR Bedienungsanleitung

Directed

Directed DS4+ Bedienungsanleitung

Directed

Directed 5305 Bedienungsanleitung

Directed

Directed Xpresskit dball 2 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed DIRECTECHS CHRYSLER8 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed DS4+ Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed 933.SUBARU5 Bedienungsanleitung

Directed

Directed DS3+ Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung