DMP Electronics Aqualite 7560A Bedienungsanleitung

InstallatIon GuIde

Thinline™ LCD Keypads

7560, 7563, 7570, 7573

Aqualite™ LCD Keypads

Models 7560A, 7563A, 7570A, 7573A

Information furnished by DMP is believed to be accurate and reliable.

This information is subject to change without notice.

LCD Keypad Installation Guide 1

DMP Keypad Features

The DMP Thinline™ and Aqualite™ LCD Keypads offer exible features and

functionality in stylish design choices.

Each keypad provides:

• Custom 16-character home or business name

• Four 2-button Panic keys

• AC power LED

• Armed LED

• 32-character display

• Backlit keyboard with easy-to-read lettering

• Internal speaker.

• Keyboard and logo backlighting turns Red in alarm conditions

• Simple harness connection to 4-wire keypad bus

• Optional backboxes for conduit or wall-mount applications

• The Thinline and Aqualite logo is also backlit.

The Models 7570/7573 and 7570A/7573A keypads provide four fully programmable

Class B, Style A, supervised, power limited protection zones you can program for a

variety of burglary and access control applications.

The Model 7563/7573, and 7563A/7573A keypads provide a built-in proximity card

reader designed to read DMP/HID proximity credentials.

The Model 7573 and 7573A keypads provide a door strike relay and allow Wiegand

input from external card readers.

2 LCD Keypad Installation Guide

Installing the Keypad

All DMP keypad housings are designed to easily install on any 4” square box, 3-gang

switch box, DMP 695 and 696 backbox, or a at surface. Figure 1 shows the keypad

housing base mounting hole locations.

Remove the Cover

The keypad housing is made up of two parts: the front, which

contains the circuit board and keyboard components and

the base. Use the following steps and gures to separate the

keypad front and base.

1. Insert a at screwdriver into one of the slots on the

bottom of the keypad and gently lift the screwdriver

handle toward you while pulling the halves apart. Repeat

with the other slot.

2. Using your hands, gently separate the front from the base

and set the front and components aside.

Harness Wiring

Figure 1 shows wiring harness assignments. Observe wire colors when connecting the

red, yellow, green, and black wires to the keypad bus. Connect red to panel terminal

7, yellow to terminal 8, green to 9, and black to panel terminal 10. Use 1k Ohm EOL

resistors, DMP Model 311, on keypad zones 1 through 4.

The 7560/7560A keypads are supplied with a 4-wire harness for panel keypad bus

connection.

The 7570/7570A and 7573/7573A keypads are supplied with a 12-wire data bus/zone

harness. Four wires connect to the keypad bus. The remaining eight wires are for the

four zone inputs: two wires for each zone.

The 7573/7573A keypads are supplied with one 5-wire output/reader harness.

Additional Power Supply

If the current draw for all keypads exceeds the panel output, provide additional

current by adding a Model 505-12 auxiliary power supply. Connect all keypad black

ground wires to the power supply negative terminal. Run a jumper wire from the

power supply negative terminal to the panel common ground terminal. Connect all

keypad power (+12 VDC) wires to the power supply positive terminal. Do NOT connect

the power supply positive terminal to any panel terminal. Refer to the 505-12 Power

Supply Installation Guide (LT-0453).

Lift screwdriver

handle up

toward you to

separate keypad

cover from base.

Thinline

or Aqualite

Keypad

Building Wall

LCD Keypad Installation Guide 3

Keypad Bus Monitor

For Fire Protective systems, the Model 893A Module must be installed in the XR100/

XR500 or XR150/XR350/XR550 Series control panels to monitor the keypad bus and

sound an audible trouble alert whenever the keypad bus fails to operate. Refer to the

893A Module Installation Sheet (LT-0135).

The Model 277 Buzzer may be installed as an audible trouble alert in place of the

Model 893A Module for XR150/XR350/XR550 Series control panels. Refer to the 277

Buzzer Module Installation Sheet (LT-1296).

Card Readers

When a proximity credential is presented to an internal or external reader, a beep

tone is heard and the Power and Armed LEDs blink. This provides both an audible and

visual acknowledgement of the credential read.

Internal Access Control Reader

The 7563/7563A and 7573/7573A keypads provide a built-in proximity card reader

designed to read DMP/HID 1300 Series proximity credentials.

Note: For listed access control applications, the keypad must be installed within the

protected area.

External Access Control Reader

To accept Wiegand data input from other external card readers, connect a 12 VDC

external reader to the 7573/7573A keypad. Connect the Red and Black power wires

from the reader to the power wires from the panel. These connect in parallel with

the keypad power wires. Connect the Reader (Data 1) wire to the White wire on the

5-wire keypad harness. Connect the Reader (Data 0) wire to the Green/White wire on

the 5-wire keypad harness. See Figure 2.

1K EOL

Green/White– Connect Reader Data 0

White – Connect Reader Data 1

Orange – Door Strike Normally Open

Gray – Door Strike Common

Violet – Door Strike Normally Closed

Yellow/White

White/Yellow

Orange White

White/Orange

Red/White

White/Red

Brown/White

White/Brown

Black – Ground

Green – Receive Data

Yellow – Send Data

Red – Keypad Power

– Zone 4

– Zone 3

– Zone 2

– Zone 1

External

Reader/

Door Strike

7573/7573A

Keypads

All Keypads

Zones

1 through 4

7570/7570A,

7573/7573A,

Keypads

Surface and Backbox

Mounting Holes

Combined 4-square

and 3-gang switch box

Mounting Holes

Keypad Back

Surface and Backbox

Mounting Holes

All zones are supervised and suitable for fire applications

Maximum zone line impedence 100 Ohms

Ground fault detected at 1420 Ohms or less

Figure 1: Keypad Back Showing Wiring Harness Assignments

4 LCD Keypad Installation Guide

1K EOL

Green/White – Connect Reader Data 0

White – Connect Reader Data 1

Orange – Door Strike Normally Open

Gray – Door Strike Common

Violet – Door Strike Normally Closed

Yellow/White

White/Yellow

Orange White

White/Orange

Red/White

White/Red

Brown/White

White/Brown

Black – Ground

Green – Receive Data

Yellow – Send Data

Red – Keypad Power

– Zone 4

– Zone 3 Request to Exit (option)

– Zone 2 Door Contact (option)

– Zone 1 7/0 Panic (option)

To Keypad Bus

External Card

Reader

Figure 2: 12 VDC Reader Wiring

Door Strike Relay Specications

The 7573/7573A keypads provide one internal programmable Form C single pole,

double throw (SPDT) relay for controlling door strikes or magnetic locks. Three wires

on the 5-wire harness, Violet (N/C), Gray (Com), and Orange (N/O), allow you to

connect devices to the relay. The Form C relay draws up to 15mA of current and the

contacts are rated for 1 Amp resistance at 30 VDC maximum.

Wiring the 333 Suppressor

One Model 333 Suppressor is

included with the 7573/7573A,

keypads. If the device being

controlled by the relay is

connected to the N/O and C wires,

install the suppressor on the

N/O and C wires. If the device is

connected to the N/C and C wires,

install the 333 on N/C and C wires.

Refer to Figure 3.

Door Strike Relay Operation

As soon as the user code sent from

the reader is veried by the panel,

the keypad door strike relay activates for 5 seconds. During this time, the access door

connected to Zone 2 must be opened to start the programmed entry/exit timer and

zone Soft-Shunt.

Note: The 5-second door strike is programmable in the panel when the keypad is used

on an XR100/XR500 or XR150/XR350/XR550 Series panel. Refer to the program guide

as needed.

Model 333

Supressor

Common

–+

Magnetic Door Lock

DMP 502 or 505

Power Supply

Normally Open

Green/White – D0

White– D1

Orange – N/O

Gray – C

Violet – N/C

N/O

N/C

Normally

Closed

Keypad

5-Wire Harness

Figure 3: 5-wire Harness/Suppressor Installation

LCD Keypad Installation Guide 5

Zone 2 Door Contact with Soft-Shunt™

If the door being released by the 7573/7573A keypad is protected, you can provide

a programmed shunt time by connecting its contact to Zone 2 (White/Red pair) on

the keypad and enabling the Soft-Shunt feature. See ZONE 2 SHUNT later in this

document. Door contacts may be N/C or N/O.

Note: The Door Strike time is programmable when the keypad is used on an XR100/

XR500 or XR150/XR350/XR550 Series panel.

Zone 3 Request to Exit

You can also connect a N/O PIR (or other motion sensing device) or a mechanical

switch to Zone 3 (White/Orange pair) on the 7573/7573A keypad to provide request

to exit capability. See ZONE 3 EXIT later in this document. When Zone 3 shorts,

the keypad relay activates for 5 seconds. During this time, the user can open the

protected door to start the programmed Soft-Shunt entry/exit timer. If the door is not

opened within 5 seconds, the relay restores to its locked state.

Note: A Zone 3 Request to Exit is inhibited for 3 seconds after the keypad reads a

card and a door strike occurs. This is to allow entry to the area and pass under a

Request-to-Exit PIR.

Panic Key Options

2-Button Panic Keys

All keypads offer Panic key function that

allows users to send Panic, Emergency,

or Fire reports to the central station.

Enable the Panic key function in the

keypad user menu. See Keypad Programming Instructions later in this document.

Install the supplied icon labels below the top row of Select keys as shown in Figure 4.

The user must press and hold the two Select keys for two seconds until a beep from

the keypad is heard. At the beep, the panel sends the following zone alarm reports to

the central station:

Panic (left two Select keys)—Zone 19 + Device Address

Emergency—non-medical (center two Select keys)—Zone 29 + Device Address

Fire (right two Select keys)—Zone 39 + Device Address

7/0 Panic Keys

All keypads also allow the user to initiate an Panic alarm by pressing the 7 and 0

(zero) keys simultaneously for one-half (1/2) second. Enable the 7/0 Panic function in

Installer Options. See Keypad Programming Instructions later in this document. When

enabled, all keypads send a Zone Short message to the panel for the rst zone of

the keypad address. When the keys are released a Zone Restore message can be sent

from the initiating keypad.

To produce a panic alarm, program the rst zone of the keypad address as a

panic type in panel programming. Place a 1k Ohm end-of-line (EOL) resistor, DMP

Model 311, across the White/Brown pair of zone wires on models 7570/7570A and

7573/7573A. This allows a Zone Restore message to be sent when the keys are

released. The 1k Ohm EOL resistor is not required on 7560/7560A or 7563/7563A

keypads.

Figure 4: Label Placement

Top Row Select Keys

Police Emergency Fire

6 LCD Keypad Installation Guide

Internal Speaker Operation

All keypads emit standard tones for key presses, entry delay, and system alerts. The

speaker also provides distinct burglary, re, zone monitor, and prewarn cadences.

The keypads provide an alternate prewarn with alarm cadence that occurs when the

status list displays a zone alarm.

Backlighting

On Thinline and Aqualite keypads, both the logo and keyboard light when a key is

pressed or the speaker sounds.

On Security Command keypads, only the keyboard lights when a key is pressed or the

speaker sounds. The backlighting dims to medium whenever the speaker is on.

During an alarm condition, all lighted areas turn Red. When all alarm conditions are

cleared from the display, the Red display turns off and the lighted areas return to the

user-selected brightness.

End-User Options

All keypads provide three keypad adjustments the end-user can make through a User

Options Menu. The user can also view the keypad model number and address.

On all keypads press and hold the Back Arrow (<—) and CMD (COMMAND) keys for two

seconds to access User Options. The keypad display changes to SET BRIGHTNESS. Use

the COMMAND key to display the next Option or press the Back Arrow to exit.

Set brightneSS

<        >

Backlighting Brightness

Set the keypad LCD Display brightness level, Power and

Armed LEDs, and the Green keyboard and logo backlighting.

Use the left Select key to lower the brightness and the right

Select key to raise the brightness. If the brightness level is

lowered, it reverts to maximum intensity whenever a key

is pressed. If no keys are pressed, and the speaker has not

sounded for 30 seconds, the user-selected brightness level

restores.

Set tOne

<        >

Internal Speaker Tone

Set the keypad internal speaker tone. At the SET TONE

display, use the left Select key to lower the tone and the

right Select key to raise the tone.

Set VOLUMe LeVeL

<        >

Internal Volume Level

Set the keypad internal speaker volume for key presses

and entry delay tone conditions. During alarm and trouble

conditions, the volume is always at maximum level. Use the

left Select key to decrease the volume and the right Select

key to increase the volume.

MOdeL nUMber

7573 V303 030812

Model Number

The LCD displays the keypad model number and rmware

version and date. The user cannot change this information.

Keypad addreSS

Keypad Address

The LCD displays the current keypad address. The user

cannot change the keypad address.

LCD Keypad Installation Guide 7

Entering Alpha Characters

To enter an alpha character, press the key that has the desired letter written below

it. The keypad display shows the number on that key. To change the number to a

letter, press the top row Select key that corresponds to the letter location under the

key. For example, if you press key number 1, the letters for that key are A, B, and C.

Press the rst Select key for A, the second Select key for B, the third Select key for C,

and the fourth Select key for special characters.

A B C (

First Letter

Second Letter Special Letter

Third Letter

Figure 5: Entering Alpha Characters

Entering Non-Alphanumeric Characters

Each key also has a special, non-alpha character. These characters are not shown on

the keypad. Enter a space by pressing 9 then the third Select key. The following non-

alpha characters are available: ( ) ! ? / & $ ‚ (space) ’ starting with the left bracket

on the 1 digit key to the blank space and apostrophe on the 9 digit key. Use the 0

digit key to enter - . * # (dash, period, asterisk, or number sign). See Figure 6.

Figure 6: Keys with Non-Alpha Characters

Installer Options Menu

All keypads provide Keypad Option and Keypad Diagnostic menus to allow installing

and service technicians to congure and test keypad operation.

Accessing Installer Options

Access the Installer Options Menu through the User Options function. Hold down the

Back Arrow and COMMAND keys for two seconds to display SET BRIGHTNESS. Enter

the code 3577 (INST) and press COMMAND. The display changes to KPD OPT (keypad

options) KPD DIAG (keypad diagnostics) and STOP.

The Keypad Options menu allows you to set the keypad address, select Supervised

or Unsupervised mode, change the default keypad message, selectively enable the

2-button Panic keys, Soft-Shunt, Request-to-Exit, and set entry card options.

Note: All programming options display on all keypads, however, actual operation for

some programming options is restricted to the listed keypads.

8 LCD Keypad Installation Guide

Programming Keypad Options

Kpd Kpd

Opt diag StOp

Keypad Options (KPD OPT)

To program keypad options, press the left Select key under

KPD OPT.

CUrrent Keypad

addreSS: 01

Keypad Address

Set the keypad address from 01 to 08 with the XT30, XT50,

XR100, and XR150. Set the keypad address from 01 to 16

with the XR500, XR350, and XR550. The factory default

address is set at 01. To change the current address, press any

Select key and enter the new address. It is not necessary to

enter a leading zero for addresses 01 to 09.

Keypad MOde:

*SUp UnSUp

Keypad Mode

Congure the keypad for either Supervised or Unsupervised

operation. Keypads with zones connected to them must be

supervised and cannot share addresses with other keypads.

Unsupervised keypads can operate with other unsupervised

keypads sharing the same address. Zones cannot be used on

unsupervised keypads. To change the current setting, press

the Select key under SUP or UNSUP. An asterisk appears next

to the selected option.

Note: Unsupervised addresses cannot be used when Device

Fail Output has a programmed value other than zero.

deFaULt Keypad

MSg:

Default Keypad Message

Enter a custom message of up to 16 characters to appear on

the keypad display top line whenever that line is not used for

any other purpose. Press any Select key to clear the current

message and enter a new custom display.

arM paniC KeyS:

*pn *eM *Fi

Arm Panic Keys

Use this option to congure the top row Select keys as

2-button Panic keys. To enable or disable a Panic, press the

Select key under the appropriate display: PN (Panic), EM

(Emergency), and FI (Fire). Once the panic is enabled, an

asterisk displays next to the description. Refer to the Panic

Key Options section earlier in this document.

7/0 paniC

enabLe: nO yeS

7/0 Panic

Select YES to congure the 7 and 0 keys as a 2-button Panic

keys. To disable the option, select NO. Default is NO. Refer

to the Panic Key Options section earlier in this document.

aCtiVate zOne 2

ShUnt: nO yeS

Zone 2 Shunt (7573/7573A only)

Select YES to enable the Soft-Shunt™ option on zone 2

as described earlier in this document. This zone provides

the Soft-Shunt™ for door contacts. This zone must be

programmed into the panel.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DMP Electronics Tastenfeld Handbücher

DMP Electronics

DMP Electronics SC Series Montageanleitung

DMP Electronics

DMP Electronics Thinline 7463 Installationsanleitung

DMP Electronics

DMP Electronics 7760 Bedienungsanleitung

DMP Electronics

DMP Electronics 532XR Bedienungsanleitung

DMP Electronics

DMP Electronics Easy Entry 693 Montageanleitung

DMP Electronics

DMP Electronics Thinline 7300 Series Installationsanleitung

DMP Electronics

DMP Electronics Thinline 7060 Bedienungsanleitung

DMP Electronics

DMP Electronics 7800 Series Installationsanleitung

DMP Electronics

DMP Electronics ePAD 5.0 Betriebsanleitung

DMP Electronics

DMP Electronics Thinline 7060 Bedienungsanleitung

DMP Electronics

DMP Electronics 7000INT Series Installationsanleitung

DMP Electronics

DMP Electronics 9800 Series Bedienungsanleitung

DMP Electronics

DMP Electronics 7800 International Series Installationsanleitung

DMP Electronics

DMP Electronics 9000 Series Bedienungsanleitung

DMP Electronics

DMP Electronics 9800INT Series Installationsanleitung

DMP Electronics

DMP Electronics Thinline 7160 Bedienungsanleitung

DMP Electronics

DMP Electronics Thinline Series Bedienungsanleitung

DMP Electronics

DMP Electronics 7800 Series Installationsanleitung

DMP Electronics

DMP Electronics Security Command 670-A Bedienungsanleitung

DMP Electronics

DMP Electronics 9863 Bedienungsanleitung

DMP Electronics

DMP Electronics Thinline Series Installationsanleitung

DMP Electronics

DMP Electronics 9000 Series Installationsanleitung

DMP Electronics

DMP Electronics Thinline Series Bedienungsanleitung

DMP Electronics

DMP Electronics 9800 Series Installationsanleitung

Beliebte Tastenfeld Handbücher anderer Marken

BFT

BFT SELETTO Bedienungsanleitung

Micro Id

Micro Id MP7G3BL Gebrauchsanweisung

WindowMaster

WindowMaster WLI 130 Bedienungsanleitung

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung