DMP Electronics Thinline Series Installationsanleitung
INSTALLATION AND PROGRAMMING GUIDE
7360/7363 Thinline
Series Icon Keypads
1 2 3 4
5 6 7 8
9 0 CMD
A
C
B
D
F
E
G
I
H
J
L
K
V
X
W
S
U
T
P
R
Q
M
O
N
Y
Z
E
N
T
E
R
B
A
C
K
ALL RESET HOME CODE
CHIME PERIM SLEEP EXIT
ZONE OUTPUT TEST INST
About the 7360/7363 ................................ 1
Card Reader............................................................ 1
Proximity Credentials Compatibility............. 1
7360/7363 Features...................................2
Install the 7360/7363 ................................3
Remove the Cover............................................... 3
Wire the Keypad.................................................. 4
Install the System Information Reference
Card .......................................................................... 4
Mount the Keypad............................................... 4
Additional information ..............................6
Additional Power Supply.................................. 6
Panic Key Options............................................... 6
Internal Speaker Operation ............................. 7
Backlighting........................................................... 7
Program the Keypad ..................................8
End-User Options................................................ 8
Backlighting Brightness (b 8) ........................ 8
Internal Speaker Tone (S 5) ............................ 8
TABLE OF CONTENTS
Internal Volume Level (L 8) ............................ 9
Software Version (100) .................................... 9
Keypad Model Number .................................... 9
Installer Options Menu .....................................10
Panic Keys (P 0)..................................................10
Emergency Key (E 0) ....................................... 11
Fire Key (F 0) .......................................................11
Number of User Code Digits (U 4) from
Proximity Card Read (7363) ...........................11
Keypad Diagnostics........................................... 12
Keypad Bus Wiring Specifications......... 13
Product Specifications ............................ 14
Ordering Information............................... 14
Certifications............................................. 15
Accessories................................................ 16
FCC Information ....................................... 17
Industry Canada Information.................. 18
Digital Monitoring Products, Inc. | 7360/7363 Installation and Programming Guide 1
The DMP Thinline™ Series Icon Keypads provide an easy to understand icon display to
assist users when arming and disarming an All/Perimeter or Home/Sleep/Away system or
using any of the standard system features. The icons provide immediate recognition of any
system alarm as well as system status.
The Model 7360 provides three 2-button Panic keys, backlit keyboard with easy-to-read
lettering and an internal speaker.
Card Reader
The Model 7363 also provides a built-in
proximity reader designed to read standard
HID proximity credentials. When a proximity
credential is presented to the internal reader,
a beep tone is heard to provide an audible
acknowledgement of the credential read.
Proximity Credentials
Compatibility
DMP Keypads with internal proximity
readers are compatible with most standard
125Khz Prox credentials available from all
DMP proximity credentials. DMP does not
guarantee compatibility with credentials not
purchased from DMP.
ABOUT THE 7360/7363
2 7360/7363 Installation and Programming Guide | Digital Monitoring Products, Inc.
7360/7363 FEATURES
Figure 1: Thinline Series Icon Keypad
1 2 3 4
5 6 7 8
9 0 CMD
A
C
B
D
F
E
G
I
H
J
L
K
V
X
W
S
U
T
P
R
Q
M
O
N
Y
Z
E
N
T
E
R
B
A
C
K
ALL RESET HOME CODE
CHIME PERIM SLEEP EXIT
ZONE OUTPUT TEST INST
Display
Select Keys
Credential Reader
Digital Monitoring Products, Inc. | 7360/7363 Installation and Programming Guide 3
INSTALL THE 7360/7363
Remove the Cover
1. Insert a flat screwdriver into
one of the slots on the bottom
of the keypad and gently lift
the screwdriver handle toward
you while pulling the halves
apart. See Figure 2. Repeat
with the other slot.
2. Using your hands, gently
separate the front from the
base and set the front and
components aside.
1
Figure 2: Removing Cover
Cover
Base
4 7360/7363 Installation and Programming Guide | Digital Monitoring Products, Inc.
Wire the Keypad
The 7360 and 7363 keypads are supplied with a 4-wire harness for panel keypad bus
connection. Since all 7300 Series keypads operate together on the Keypad bus using
the same address, there is no address option to set.
Observe wire colors when connecting the Red, Yellow, Green, and Black wires to the
keypad bus.
When wiring directly to the panel terminals:
1. Connect Red to panel terminal 7.
2. Connect Yellow to terminal 8.
3. Connect Green to terminal 9.
4. Connect Black to terminal 10.
2
Install the System Information Reference Card
User Code instructions are on one side of the card and the opposite side oers an
area to record zone numbers and names. Figure 3 shows the location of the pull-out
card holder on the back of the keypad.
While the keypad is attached to the wall, insert the bottom of the card at an angle to
align the card into the bottom slot, then slide the card in place.
3
Mount the Keypad
All DMP keypad housings are designed to easily install on any 4” square box, 3-gang
switch box, DMP 695 and 696 backbox, or flat surface.
4
Digital Monitoring Products, Inc. | 7360/7363 Installation and Programming Guide 5
Black – Ground
Green – Receive Data
Yellow – Send Data
Red – Keypad Power
Reference Card
Guide Tabs
Surface and Backbox Mounting Holes
Combined 4-square and 3-gang Switch Box Mounting Holes
Keypad Back
Figure 3: Keypad Back with Wiring Harness
6 7360/7363 Installation and Programming Guide | Digital Monitoring Products, Inc.
ADDITIONAL INFORMATION
Additional Power Supply
If the current draw for all keypads exceeds the panel output, provide additional current by
adding a Model 505-12 auxiliary power supply. Connect all keypad Black ground wires to
the power supply negative terminal. Run a jumper wire from the power supply negative
terminal to the panel common ground terminal. Connect all keypad power (+12 VDC) wires
to the power supply positive terminal. Do not connect the power supply positive terminal
to any panel terminal. Refer to the 505-12 Power Supply Installation Guide (LT-0453) for
more information.
Panic Key Options
2-Button Panic Keys
All keypads oer a panic key function that allows users to send Panic, Emergency, or Fire
reports to the central station. In order to use the panic keys, enable the functions in the
keypad user menu. See Programming Keypad Options later in this document. Install the
supplied icon labels below the top row of Select keys as shown in Figure 4.
Press and hold the two Select keys for two seconds until a beep from the keypad is heard.
At the beep, the panel sends the zone alarm reports shown in Table 1to the central station.
Note: All 7300 keypads send address 8 as a default on panic alarms.
Andere Handbücher für Thinline Series
4
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere DMP Electronics Tastenfeld Handbücher
DMP Electronics
DMP Electronics Thinline 7060 Bedienungsanleitung
DMP Electronics
DMP Electronics 9800 Series Installationsanleitung
DMP Electronics
DMP Electronics 7872 Bedienungsanleitung
DMP Electronics
DMP Electronics 7872 Bedienungsanleitung
DMP Electronics
DMP Electronics Security Command 670 Bedienungsanleitung
DMP Electronics
DMP Electronics Thinline 7463 Installationsanleitung
DMP Electronics
DMP Electronics 7800 Series Installationsanleitung
DMP Electronics
DMP Electronics Thinline Series Bedienungsanleitung
DMP Electronics
DMP Electronics 7000INT Series Installationsanleitung
DMP Electronics
DMP Electronics 791 Easy Entry Montageanleitung
DMP Electronics
DMP Electronics 9000 Series Installationsanleitung
DMP Electronics
DMP Electronics Aqualite 7560A Bedienungsanleitung
DMP Electronics
DMP Electronics Security Command 690 Bedienungsanleitung
DMP Electronics
DMP Electronics Thinline 7160 Bedienungsanleitung
DMP Electronics
DMP Electronics 9800 Series Installationsanleitung
DMP Electronics
DMP Electronics 692 Security Command Montageanleitung
DMP Electronics
DMP Electronics Thinline 7060 Montageanleitung
DMP Electronics
DMP Electronics ePAD 5.0 Betriebsanleitung
DMP Electronics
DMP Electronics Thinline Series Bedienungsanleitung
DMP Electronics
DMP Electronics 7872 Bedienungsanleitung
