DNP DS?RX1 Bedienungsanleitung

User’s Manual

DS-RX1

Version 1.03

●Concerning Copyright

The copyrights for this document are the property of Dai Nippon Printing Co., Ltd.

Reproduction of any or all of the contents of this document without consent of the company is

a violation of copyright law. However, one back-up copy may be made for non-commercial,

personal purposes.

Also, the contents of this document are subject to change in the future without prior notice.

●Concerning Safety Warnings

Warnings concerning safety and use, and the contents of this document, conform to existing

standards as of the date published.

●Concerning Modification

This printer was planned, developed, and manufactured by Dai Nippon Printing Co., Ltd., an

for safety purposes, any modification of the device is prohibited.

Introduction

Thank you for purchasing this device.

This document explains the handling and operation required to use this printer.

Please read this document well before use.

Be sure to read “For Safe Operation” (Pg 2-4), and operate the printer correctly.

For Safe Operation

・ Be sure to read this document before use. After reading, keep it in a safe place, where it can be re-read as

needed.

・ The warnings listed here are to ensure proper use of the device, to prevent physical injury to the customer or

other persons, and to prevent property damage. Please obey these warnings.

■ About “Warning” and “Caution”

Listed below, the possible levels of injury or damage due to misuse are categorized as “Warning” and

“Caution”, according to the degrees of danger involved.

■ About the symbols

The symbols shown have the following meanings:

This symbol calls attention to contents of warnings and cautions.

Details are indicated in or near this s

mbol.

This symbol indicates prohibited actions.

Details are indicated in or near this s

mbol.

This symbol designates necessary actions, and relevant content.

Details are indicated in or near this symbol.

Accidents caused by failure to heed the warnings accompanying this symbol could lead to

serious or fatal injury.

WARNING

Accidents caused by failure to heed the warnings accompanying this symbol could lead to

hysical injury or property damage.

CAUTION

WARNING

・ Use only with the designated voltage and frequency. Improper connection could cause electric

shock or fire.

・ Avoid overstressing outlets and using extension cords. The outlet could overheat and cause

fire.

・ Do not damage, destroy, bundle, or alter the power cord. Also, placing heavy objects on,

pulling on, or bending the cord excessively can damage it, and could cause a fire.

・ Do not set the printer up in places with salinity or corrosive gases in the air. This could cause

fire.

・ Do not block the vents. Heat could build up in the printer and cause a malfunction or fire.

・ Do not stand on or place heavy objects on the printer. Also, do not use excessive force on the

buttons, switches, terminals, etc. This could break the printer and cause injury to the user o

others.

・ Be careful to avoid injury or damages from the edges in the printer.

・ Do not use this printer for applications where malfunction could be life-threatening

(such as medical, space, aeronautic, or other applications that require extreme reliability).

・ The printer weighs approximately 14 kg (31 lbs). When moving it, lift in a way that avoids

excessive physical stress. Lifting recklessly or dropping the printer could cause injury.

・ Locate the printer as close to an outlet as possible, and allow easy access to unplug the powe

cord in case of problems.

・ If there is dust on the plug, clean it off thoroughly. It could cause electric shock or a short-out.

・ If metal objects or liquids have fallen into the printer, and there is smoke, a strange odor, or an

other apparent abnormality, immediately turn the power OFF, and unplug the power cord. The

contact a service representative. Do not continue using the printer if it is not operating properly.

This could cause shock, short circuit, or fire.

・ Be sure to attach the ground. Otherwise, it could short-circuit, causing electric shock or fire.

・ Do not plug or unplug the cord with wet hands. This could cause electric shock.

・ Do not open the inside of the printer, disassemble internal

arts, or modify the printer. It coul

cause electric shock, fire, or injury, or break the printer. For internal check-ups, adjustments, o

repair, please contact a service representative.

CAUTION

・ Do not set the printer up in dusty or overly humid places. This could cause fire or electric shock, or

damage the printer.

・ Do not set the printer up on an unstable surface. It could fall and cause injury to the user or others.

・ Do not allow foreign objects to enter the printer. They could cause electric shock, short circuit, o

fire, or break the printer. If something falls into the printer, immediately turn the power OFF, an

call a service representative.

・ Do not open the cover while printing. This could break the printer.

・ Do not spill or spray liquids or chemicals into the printer.

・ When cleaning the cover, do not use thinner, trichloroethane, benzene, ketone-

ased cleaners, o

chemically treated cloths. They could discolor or deteriorate the cover.

・ At least once a year, unplug the power cord, and clean the prongs and the plug. If dust accumulates,

it could cause a fire.

・ When printing continuously for long periods of time in a small room, be sure to ventilate properly.

・ If use is intended on a transportation vehicle (train, truck, ship, etc.), please talk to a representative in

advance.

・ When disposing of the printer, peripheral items, packaging, or media, please abide by local waste

removal ordinances. For details, contact your local government offices.

・ When unplugging the cord, grip the plug. Do not pull on the cord. It could damage the cord, an

cause electric shock or fire.

・ When moving the printer, be sure to unplug the power cord. Otherwise, the cord may be damaged,

which could cause fire or electric shock.

・ When not using the printer for extended periods of time, for the sake of safety, be sure to unplug the

power cord. It could cause electric shock or fire.

・ The thermal print head gets very hot. Do not touch after printing. There is a danger of burns.

・ Do not touch the gear mechanisms. There is a danger of injury if fingers get caught in the spinning

gears.

If you want to dispose this product, do not mix with

eneral

household waste. There is a separate collection s

stem for

used electronics products in accordance with le

islation

under the WEEE Directive (Directive 2002/96/EC) and is

effective only within European Union.

Cautions for Set-up

・ Prior to operation, read “For Safe Operation” carefully and observe the rules therein.

・ Use care when moving the printer. Never try carrying the printer alone.

Dropping it could cause injury or damage to other property.

・ Do not use or store the printer near fire, excessive moisture, in direct sunlight, near an air

conditioner or heater, or any other source of unusually high or low temperature or humidity, or

excessive dust.

・ Do not place the printer where chemical reactions occur, such as in a laboratory.

・ Do not set up the printer where there is salinity or corrosive gas in the air.

・ The printer must sit on a firm level surface where there is ample ventilation.

・ Do not put anything on the top of the printer.

・ Do not place the printer near a radio or television, and do not use the same wall outlet for the

printer and radio or television. Radio or television reception could be adversely affected.

・ Do not use a power voltage or frequency other than those specified.

・ Do not put anything on the power cord or step on it.

・ Do not drag or carry the printer by the power cord or USB cable.

・ Avoid plugging the power cord into an outlet with many loads.

・ Do not bundle the power cord.

・ Always grip the plug housing, not the cord, to plug/unplug the power cord.

・ Make certain the power is turned off before connecting/disconnecting the USB cable.

・ Avoid lengthening the signal cable or connecting it to any noise-producing device.

If it is unavoidable, use a shielded cable or twisted pair for each signal.

・ Use a USB cable with shielding suitable for the USB 2.0 specification.

・ Place the printer near the outlet where the power cord can be unplugged easily to shut off

power.

・ Use an AC outlet that accepts a three-pronged plug. Otherwise, there may be danger of electric

shock.

・ Use the appropriate specified cord set.

Only use items that are certified safe according to the standards of the country where they are to

be used.

Regulatory compliance statements

American users

FCC part 15

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his or her own

expense.

You are cautioned that changes or modifications not expressly approved by the party

responsible for compliance could void your authority to operate the equipment

This device complies with FCC radiation exposure limits set forth for an uncontrolled

environment. The antenna used for this transmitter must be installed to provide a separation

distance of at least 20 cm from all persons and must not be co-located or operating in

conjunction with any other antenna or transmitter.

Caution: Use shielded cables to connect this computers.

Any changes or modifications not expressly approved by the grantee of this device

could void the users authority to operate the equipment.

日本のお客様へ

電波障害について

この装置は、クラスＡ情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こ

すことがあります。この場合には使用者が適切な対策を講ずるよう要求されることがあります。

ＶＣＣＩ－Ａ

Declaration of Conformity

European users

Hereby, Dai Nippon Printing Co., Ltd., declares that this digital color printer is in co

mpliance with the essential requirements and other relevant provisions of Directive

1999/5/EC.

Table of Contents

Introduction・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 2

For Safe Operation・・・・・・・・・・・・・・・・・・・・・・・・・・ 2

Cautions for Set-up ・・・・・・・・・・・・・・・・・・・・・・・・・・ 5

Regulatory compliance statements ・・・・・・・・・・・・・・・・・・・・ 6

Declaration of Conformity ・・・・・・・・・・・・・・・・・・・・・・・7

Table of Contents ・・・・・・・・・・・・・・・・・・・・・・・・・・ 8

Setting Up the Printer

Checking the Contents ・・・・・・・・・・・・・・・・・・・・・・・ 9

Names of Components・・・・・・・・・・・・・・・・・・・・・・・・ 10

Connecting・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 11

Paper, Ribbon・・・・・・・・・・・・・・・・・・・・・・・・・・・ 12

Setting the Media・・・・・・・・・・・・・・・・・・・・・・・・・・ 13

Setting the Scrap Box・・・・・・・・・・・・・・・・・・・・・・・・ 16

Setting the Paper Tray・・・・・・・・・・・・・・・・・・・・・・・・ 16

Trouble-shooting

Error Displays ・・・・・・・・・・・・・・・・・・・・・・・・・・・ 17

Solving Media Errors・・・・・・・・・・・・・・・・・・・・・・・・ 18

Cleaning

Platen Roller・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 21

Thermal Print Head・・・・・・・・・・・・・・・・・・・・・・・・・ 21

Repacking ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 22

Specifications・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 24

Setting Up the Printer

Checking the Contents

Please check that the printer and all accessories are included in the package.

When using, remove the Protective pad.

Please keep the package box and

packing material for transportation.

・ When removing the printer from its package, carrying it, or moving it, be sure to use care.

Dropping the printer could result in personal injury or damage to other items.

・ If the printer is lifted by grasping the cushions, the cushions could break and cause the printe

to be dropped.

CAUTION

CD (*)

User’s Manual

Printer Driver

Power Cord (*) Paper Tray (*)

(Only for L and PC sizes)

For Safe Operation (*)

Start-up Guide (*)

Scrap Box

Printer Unit

er Holde

(*) mark accessories may not be contained according to the destination.

Protective pad

Andere Handbücher für DS?RX1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung