Dräger Babylog VN500 Kurzanleitung

D-12377-2016

Disassembly/Assembly Muﬄer

Open the ﬂap by lifting the lower

edge upwards.

Close the ﬂap.

Pull the muﬄer as far it will go

to the left.

Push the muﬄer to the

right into the socket.

Remove the expiratory valve from

the ﬁtting.

Turn the locking ring as far as

possible to the left.

Remove and empty the water

trap container.

Fit the muﬄer into the socket.

Remove the muﬄer from

the socket.

Remove the diaphragm.

Fit the water trap container.

Fit the diaphragm onto the edge

of the expiratory valve housing.

Turn the locking ring as

far as it will go to the right

until it clicks into place.

Turn the locking ring as far as

possible to the left and push the

expiratory valve into the ﬁtting.

Dräger Babylog® VN500

Neonatal Expiratory Valve

and Neonatal Flow Sensor

Disassembly/Assembly and Reprocessing

Disassembly/Assembly Neonatal Expiratory Valve

The muﬄer is only attached to the Babylog® VN500. It is only available with

an 11 mm diameter port. The Babylog® VN500 is dedicated to neonatal and

pediatric patient population.

This guideline does not replace or amend the instructions for use for Inﬁnity Acute Care System Workstation Neonatal Care.

The instructions for use and the hospital guidelines and policies always have to be observed.

D-12377-2016

Disassembly/Assembly Neonatal Flow Sensor

Remove the breathing hoses

from the neonatal ﬂow sensor.

Fit the breathing hoses to

the neonatal ﬂow sensor.

Disconnect plug of the ﬂow

sensor cable from the

neonatal ﬂow sensor.

Connect plug of the ﬂow

sensor cable to the

neonatal ﬂow sensor.

Fit the insert into

the ﬂow sensor.

Gently press the knobs on

both sides while pulling the

insert out of the neonatal

ﬂow sensor.

Dräger Babylog® VN500

and Neonatal Expiratory Valve

Reprocessing

Neonatal Flow Sensor

Disassembly/Assembly

Before manual cleaning

prepare cleaning solution. Before

and after immersion ﬁt a syringe

containing 20 ml of solution to

the ejector channel. Inject and

extract the solution several times.

Reprocessing of Neonatal Expiratory Valve

This guideline does not replace or amend the instructions for use for Inﬁnity Acute Care System Workstation Neonatal Care.

The instructions for use and the hospital guidelines and policies always have to be observed.

Prepare cleaning solution.

Immerse ﬂow sensor housing

and sensor insert bubble-free

in the cleaning solution.

Ensure that the solution ﬂushes

all surfaces and interior spaces.

At the beginning and end of the

entire reprocessing procedure

vigorously swirl both parts for at

least one minute.

... until no cleaning agent

residues can be recognized.

For disinfection, repeat step 1 to 4 with disinfection solution.

For disinfection, repeat step 2a to 2c with disinfection solution.

Suﬃciently rinse the housing and

the insert in water (preferably

drinking-water quality) ...

* The Neonatal Flow Sensor is also working with Evita® V300 and Evita Inﬁnity® V500.

Reprocessing of ISO 15 Neonatal Flow Sensor

and Y-piece Neonatal Flow Sensor*

D-12377-2016

At the beginning of immersion

(step 1 and 2) ﬂush each opening

of the housing with cleaning

solution using a 20 mL syringe.

At the end of immersion ﬂush

each opening of the housing

once more with cleaning solution

using a 20 mL syringe.

Clean the housings with a lint-free

brush: Insert the brush ten times

each vertically into both ports of

Y-piece and pull it out again and

insert it ten times each diagonally

into both angles of the opening

for the sensor insert and pull it

out again.

When using Y-piece Neonatal Flow Sensor please add the steps 2a-2c to the cleaning and disinfection immersion step

(step 1 and 2), always using the corresponding cleaning or disinfection solution.

Check parts for visible soiling or

damage. Check the sensor insert

for damage to the measuring

wires and their pegs. Thoroughly

shake out residual water.

Allow the ﬂow sensor to air dry for

at least 30 minutes.

Final check and drying for

both Flow Sensors

2a 2b 2c

Dräger Babylog® VN500

and Dräger Neonatal Flow Sensor

Reprocessing instructions

Manual cleaning and disinfection

This guideline does not replace or amend the instructions for use for Inﬁnity Acute Care System Workstation Neonatal Care.

The instructions for use and the hospital guidelines and policies always have to be observed.

Manual cleaning

and disinfection

Machine cleaning

and disinfection

Sterilization

Reprocessing instructions overview:

D-12377-2016

housing and sensor separately

without sensor

sensor and housing connected

Machine cleaning and disinfection:

Securely position the product in the basket.

Ensure the following:

– All surfaces and interior spaces can be

ﬂ ushed completely.

– The water can drain oﬀ freely.

Sterilization:

Check the product for visible damage and replace if necessary.

For semi critical products sterilization

is possible but not necessary.

For further information please refer to Instruction for Use.

Manufacturer:

Drägerwerk AG & Co. KGaA

Moislinger Allee 53–55

23558 Lübeck, Germany

Dräger Babylog® VN500

and Neonatal Flow Sensor

Reprocessing instructions

Manual cleaning and disinfection

This guideline does not replace or amend the instructions for use for Inﬁ nity Acute Care System

Workstation Neonatal Care.

The instructions for use and the hospital guidelines and policies always have to be observed.

Andere Handbücher für Babylog VN500

Andere Dräger Medizinische Geräte Handbücher

Dräger

Dräger Oxy K 30 E Bedienungsanleitung

Dräger

Dräger Secor 7000 Bedienungsanleitung

Dräger

Dräger X-am 7000 Bedienungsanleitung

Dräger

Dräger Babylog VN800 Bedienungsanleitung

Dräger

Dräger caleo Bedienungsanleitung

Dräger

Dräger Narkomed 2C Betriebsanleitung

Dräger

Dräger Savina 300 Bedienungsanleitung

Dräger

Dräger Seattle PAP plus Bedienungsanleitung

Dräger

Dräger Gemina DUO Bedienungsanleitung

Dräger

Dräger Polaris 50 Bedienungsanleitung

Dräger

Dräger Apollo Kurzanleitung

Dräger

Dräger Polytron 7000 Bedienungsanleitung

Dräger

Dräger Oxy K 30 E Bedienungsanleitung

Dräger

Dräger Evita V Series Bedienungsanleitung

Dräger

Dräger DrugTest 5000 STK Bedienungsanleitung

Dräger

Dräger Movita Bedienungsanleitung

Dräger

Dräger Primus Series Bedienungsanleitung

Dräger

Dräger Infinity Delta Bedienungsanleitung

Dräger

Dräger Infinity Acute Care System Evita Infinity... Bedienungsanleitung

Dräger

Dräger Babylog 8000 plus Bedienungsanleitung

Dräger

Dräger Infinity Series Bedienungsanleitung

Dräger

Dräger Infinity Acute Care System Evita Infinity... Bedienungsanleitung

Dräger

Dräger X-plore 3300 Bedienungsanleitung

Dräger

Dräger Fabius OS Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung