Dream On Me 656 Bedienungsanleitung

Adult assembly required.

Small parts may present choking hazard prior to assembly.

Enclosed are step by step instructions to help you.

quickly assemble your product.Before you begin we recommend

that you follow the steps below:

1. Please read the instructions thoroughly.

2. Identify all parts and hardware.

3. You will need the following tools:

Philips head screw driver

Flat head screw driver Hammer

Do Not Use Power Drills or Drivers

To protect parts during assembly please place them on a soft surface.

To clean surface use only water on a damp cloth. Do not use

window cleaners or cleaning abrasives as it will scratch the surface

and could damage the protective coating.

ASSEMBLY INSTRUCTIONS

ITEM NO: 656

Read all instructions before assembling crib.

Save instructions for future referrence.

Dream On Me Inc.

1532 S WASHINGTON AVE

PISCATAWAY TWP NJ 08854

OFFICE: 732-752-7220

CUSTOMER SERVICE: 732-366-1788

.Read all instructions before assembling crib, keep instructions for future use.

.Upon completion of assembly be sure all screws, bolts and fastening devices have been

securely tightened. A frequent check should be made.

.Infants can suffocate in gaps between a mattress too small or too thick and product sides,

on soft bedding never add a mattress, pillow,comforter or padding.

.CAUTION: Any mattress used in this crib must be at least 27-1/4inches(690mm) by 51-5/8

inches(1310mm),with a thickness not exceeding 6 inches(150mm), the dimensions of the

.Failure to follow these warnings and the in structions could result in serious injury or death.

.Never use plastic shipping bag or other plastic film as mattress covers not sold and

intended for that purpose, as they can cause suffocation .

.Strings can cause strangulation! Never place items with a string around a child’s neck,

.Never use this product if there are any loose or missing fasteners, loose joints,broken

parts, or torn mesh/fabric. check before assembly and periodically during use.

Contact DREAM ON ME for replacement parts and instructional literature if needed.

.Never substitute parts, the product including side rails, must be fully erected prior to use.

.Discontinue use of the product when child is able to climb out or reaches the height of

.When child is able to pull to standing position,set mattress/base to lowest adjustment

position and remove bumper pads, large toys,and other objects that could serve as steps

for climbing out. A child can trap parts of the body or clothing on loose fasteners .

.Never use a water mattress with this product.

.If refinishing,use a non-toxic finish specified for children’s products.

.To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their

back to sleep, unless otherwise advised by your physician.

WARNING !

.Never place product near window where cords from blinds or drapes can strangle a child.

MADE IN CHINA

35in (890mm).

mattress shall be taken from seam to seam or edge to edge where appropriate.

such as hood strings or pacifier cords. Never suspend strings over product or attach

strings to toys.

Never place additional padding under an infant

To help prevent strangulation tighten all fasteners.

A child can trap parts of the body or clothing on loose fasteners.

Follow warnings on all products in a crib .

See head panel & mattress support of the product for warnings.

Replace teething rail if damaged,cracked or loose.

Read all instructions before use of the changing table, add-on changing unit, or contoured

changing pad. For this changing table,the maximum weight of the child is 30lbs.

Do not use changing table, add-on changing unit, or contoured changing pad if it is

damaged or broken.

890

CONNECTION HARDWARE

a: 2” b: 1-3/8”Allen head bolt (20 pcs) c: 2-3/8”Allen head bolt (6 pcs)Allen head

bolt (3 pcs)

f:Wood dowels (20pcs)

q:Allen wrench

(1pc)

d:3-1/2”Allen head bolt (6 pcs) e:Barrel nuts (12 pcs)

k: 3/4”Allen head bolt

(4 pcs)

h:1-3/8” Screw (3 pcs) i:Knob (3pcs)

g:Cross screw (24pcs) j:Shelf support (4pcs)

PARTS ENCLOSED IN CARTON

ALeft head board

A1:Left back leg (1pc)

A2:Left board (1pc)

A3:Left front leg (1pc)

BChanger side CRight back leg (1pc)

B1:Left (1pc) B2:Right (1pc)

l:Washer

(2pcs)

m:Bolt (2pcs) n:Belt (1pc) p:Tip over

restraints (1pc)

PHILLIPS--HEAD SCREWDRIVER

REQUIRED FOR ASSEMBLY

----NOT INCLUDE Do Not Use Power Drills or Drivers

GDrawer HBack rail (1pc)

JFront rail (1pc) KMetal spring support platform (1pc)

G1:Front panel (3pcs)

G2:Left side panel (3pcs)

G3: Right side panel (3pcs)

G4:Back panel (3pcs)

G5:Bottom panel (3pcs)

LPad (1pc)

DChanger middle panel EChanger bar FChanger shelf

D1:Top bar (1pc)

D2: Panel (1pc)

D3:Bottom bar (1pc) E2:Middle bar (2pcs)

E1:Bar (5pcs)

E3:Back bottom bar (1pc)

F1:Changing surface (1pc)

F2:Changer middle shelf (1pc)

F3:Changer bottom shelf (1pc)

The bottom bar (1pc)

E1 F1

CRIB ASSEMBLY

STEP 1

Attach The changer bar(E1&E2&E3) ,

and The changer middle(D1&D3)

toThe changer side (B2) using wood

dowels (f),bolts(b) and allen wrench (q).

Model shown is example only.

Styles may vary .

Lay down the assembled parts

on the floor .

Slide The changing surface (F1)

into the groove in (B2) along the

groove between (E2) and (E2) .

Slide (D2) into the groove in (B2)

along the groove between (D1) and (D3) .

Then slide (F3) into groove in

(B2) along the groove between

(E3) and (D3) .

STEP 2

Model shown is example only.

Styles may vary .

F1E2

E3 E2

STEP 3

Model shown is example only.

Styles may vary .

Attach The changer bar (E1&E2&E3) and

The changer middle (D1&D3) to The

changer side (B1) using wood dowels

(f),bolts (b) and allen wrench (q) .

Attach left back leg (A1) and

right back leg (C) to back rail (H)

using bolts (d) and barrel

nuts (e) .

STEP 4

Model shown is example only.

Styles may vary .

D3 D2

Insert the shelf supports (j) in the holes in the posts of changing table.

Then place the changer middle shelf (F2) inside the shelf support .

Tighten the screws in the shelf supports (j) .

CHECK THAT ALL BOLTS ARE TIGHTENED .

j x4

j F2

STEP 5

Model shown is example only.

Styles may vary .

Connect the assembled parts of

STEP 4 to the assembled parts of

STEP 3 by using bolt (a) and allen

wrench (q).

Connect the assembled parts to

left board (A2) by using bolt (c),

barrel nuts (e) and allen wrench (q).

Attach the left front leg (A3) to the

left board (A2) using bolt (d),

barrel nuts (e) and allen wrench (q).

Locate the mattress support (K)with tabs .

Be sure the smooth side of the

mattress support (K) is faced upward .

Position the tabs of the mattress

support(K) to mount to the selected

position onto the legs .

Insert the bolts (k) , through the

tabs and into thread inserts ,

then tighten securely with allen

wrench (q) .

STEP 6

Model shown is example only.

Styles may vary .

STEP 7

Model shown is example only.

Styles may vary .

Attach The front rail (J) to

The changer side (B1) and

The left front leg (A3) using

bolts (c),barrel nuts (e) and

allen wrench (q) .

Attach left side panel (G2) & right side

panel (G3) to back panel (G4) by

inserting cross screw (g) into the holes

on left side panel (G2) & right side panel

(G3) .

DO NOT tighten all .

STEP 8

Model shown is example only.

Styles may vary .

Inhaltsverzeichnis

Andere Dream On Me Baby- und Kleinkindmöbel Handbücher

Dream On Me

Dream On Me STORYBROOKE Bedienungsanleitung

Dream On Me

Dream On Me 626 Bedienungsanleitung

Dream On Me

Dream On Me HYGGE Bedienungsanleitung

Dream On Me

Dream On Me 629 Bedienungsanleitung

Dream On Me

Dream On Me FOLDING FULL SIZE CRIB Bedienungsanleitung

Dream On Me

Dream On Me 388 Gebrauchs- und Pflegehandbuch

Dream On Me

Dream On Me 436 Bedienungsanleitung

Dream On Me

Dream On Me Violet 7 in 1 Bedienungsanleitung

Dream On Me

Dream On Me 649 Bedienungsanleitung

Dream On Me

Dream On Me KARLEY Bedienungsanleitung

Dream On Me

Dream On Me Orion Bedienungsanleitung

Dream On Me

Dream On Me Addison Bedienungsanleitung

Dream On Me

Dream On Me SAN-FRAN Bedienungsanleitung

Dream On Me

Dream On Me 662 Bedienungsanleitung

Dream On Me

Dream On Me KARLEY Bedienungsanleitung

Dream On Me

Dream On Me 442 Bedienungsanleitung

Dream On Me

Dream On Me 643 Leitfaden

Dream On Me

Dream On Me FUNTASTIC 2-IN-1 Bedienungsanleitung

Dream On Me

Dream On Me 633 Bedienungsanleitung

Dream On Me

Dream On Me MONTREAL Bedienungsanleitung

Dream On Me

Dream On Me 630 Bedienungsanleitung

Dream On Me

Dream On Me 642 Bedienungsanleitung

Dream On Me

Dream On Me 626 Bedienungsanleitung

Dream On Me

Dream On Me 654 Bedienungsanleitung

Beliebte Baby- und Kleinkindmöbel Handbücher anderer Marken

Mocka

Mocka Learning Tower Bedienungsanleitung

VERTBAUDET

VERTBAUDET 62003-2789 Bedienungsanleitung

Summer

Summer MY FUN POTTY Bedienungsanleitung

Grotime

Grotime Changeover Bedienungsanleitung

Fillikid

Fillikid 1221 Bedienungsanleitung

Relita

Relita loft bed ALEX Bedienungsanleitung

Joovy

Joovy Qool Bedienungsanleitung

KidKraft

KidKraft Step n Store Bedienungsanleitung

Fisher-Price

Fisher-Price L4889 Bedienungsanleitung

Germania

Germania Moon 4048.101 Bedienungsanleitung

BabyGo

BabyGo Amila Bedienungsanleitung

Fisher-Price

Fisher-Price CBV06 Bedienungsanleitung

Fisher-Price

Fisher-Price H4790 Bedienungsanleitung

Graco

Graco Dream Suite Bedienungsanleitung

Delta Childrens Products

Delta Childrens Products BB87116CR Bedienungsanleitung

Costway

Costway BB5591 Bedienungsanleitung

SAUTHON

SAUTHON UP CHENE DORE UI101A Bedienungsanleitung

Delta Children

Delta Children Classic Bedienungsanleitung