DUKWIN DK Series Bedienungsanleitung
1
CATALOGUE
Introduction
1. Power
1.1 Optional Plug
2. The back of the watch winder
3. Controls
3.1 LCD Touchscreen Control Panel
3.2 Initialization Mode
3.3 All Mode
3.4 Custom Mode
3.5 New Watch Mode
4. Winding Mode
5. Remote Control
6. Fingerprint Lock
6.1 Fingerprint Accounts Setting
6.2 Fingerprint Accounts Remove/Reset
7. Watch Cuff
7.1 How to use the cuff
8. LED Light Stripe and Ambient Light
8.1 LED Light Stripe
8.2 Ambient Light
9. Contact
2
3
3
4
4
4
5
6
6
6
7
8
8
9
10
11
11
11
12
12
13
2
Congratulations on your purchase of this watch winder.
Please review this quick start guide so that your auto-
matic watch will benefit fully from the features that have
been engineered into this product.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
Appliance is only to be used with the power supply unit
provided with the appliance.
Introduction
3
9
This module fingerprint watch winder comes with a power adapter
(AC/DC5.0V-volt. 2.0A output)
1Power
NOTE:
1. External power connection is required to use fingerprint lock, external
power input is DC5V, please do not connect reverse polarity.
2. Never use any unauthorized power adapter or not up to specification
power adapter.
1.1 Optional Plug
Power supply: 5.0V AC Adapter(US/UK/AU/EU)
Suitable for various 5.0V 2.0A USB specifications plugs
US Standard EU Standard UK Standard
AU Standard
Power bank USB Connection
GW-POWER
Model :GW12W-050200UU
INPUT : 100-240V-50 / 60HZ 0.3A
Output : 5.0V 2.0A 10W MADE IN CHINA
4
2The back of the watch box
3Controls
Power Switch Pause Switch AC Adapter Input Port
PAUSE SWITCH:
When you turn on the "pause switch" and open the front cover, all drums will
immediately stop rotating. When you turn off the "pause switch" and open
the front cover, all drums continue rotating. Your watch will always stop at
the 12 o'clock position when the cycle is complete.
With the adapter connected, turn on the "Power Switch". The display will be lit
and all options will flicker back and forth, then you can set the programs by
Touchscreen Control Panel or the Remote Control.
3.1 LCD Touchscreen Control Panel
Ticked
icon
Switch(Run
/Pause/Stop)
Working Hour
/Motor Options
Direction Lights Control
TPD ALL Mode
5
(Switch Diagram)
Pause Run Stop
3.2 Initialization Mode
Initialization Mode
1. Hold down the “ALL” button for 5 seconds to display Initialization. Press the
“Run” button to perform initialization. The ticked icon will appear in the upper
left corner of the middle four choices, representing the “ALL” Mode. When you
choose any other button, initialization mode will go off and returns to the
original mode of your operation.
2. Initialization parameter: TPD=850; Direction=bidirectional; Switch =Stop;
Motor Selection=01 group; ALL=ALL selected. Working Hours=24 hours.
3. When you change any of the parameters: Switch - TPD - Direction - Lights,
the initialization mode will exit and the initialization prompt will go off.
(If you have any questions, check out our YouTube video link)
6
Tap the "ALL" button 4 times until the top left corner of each of the four
options shows a ticked icon, or Press the "motor selection" and "Run"
buttons at the same time for 5 seconds, and then tap the "Run" button. All
watches will be set to the current mode. . If you change the parameters of
“Switch - TPD - Direction”, all watches will be change to the current
parameters.
(If you have any questions, check out our YouTube video link)
Motor Options:
If the current mode is ALL, just tap the “ALL” button again, the “Motor Options”
will appear, and you can set the mode of each motor individually.
New Watch Mode: Press and hold the "TDP" button until " ----" diagram is
displayed.
Note: During the new watch mode, any operation will cause the new watch
mode to exit and return to the previous settings.
3.3 ALL Mode
Motor Options
3.4 Custom Mode
3.5 New Watch Mode
----
7
New Watch Mode Working Chart
Direction Setting Working Time Rest Time
Clockwise 4 hours
Counterclockwise 4 hours
Clockwise for 2 hours and
Counterclockwise for 2 hours
Bi-directional 8 hours
8 hours
8 hours
Finally return to the previously setting mode
4Winding Mode
1. The TPD value is between 300 - 2300. By turn up and turn down to change
TPD value, over 300 TPD returns to 2300 TPD cycle.
2. TPD Calculation Method: 10 turns per cycle
24-hour mode operating cycle (minutes) =1440/ (TPD/10 turns);
12-hour mode operating cycle (minutes) =1440/ (TPD/10 turns) /2;
8-hour mode operating cycle (minutes) =1440/ (TPD/10 turns) /3;
e.g: TPD set to 650, clockwise, 24 hours mode. Then the running period (minutes)
=22.2, that is, each cycle is 22.2 minutes.
Cycle execution: the time required for the motor to rotate clockwise 10 times
+ the motor stop time = 22.2 minutes. In the 12 (8 hours) working mode, the
cycle runs for 12 (8 hours) hours and then stops; stops for 12 (16 hours)
hours, and then restarts the cycle.
Note:
There is no magic number of rotations that will wind your watch. Things such
as how active you are, how many complications your watch has, how
frequently you use the chronograph function, how frequently you wear your
watch, the watch make, how long it has been since it was last serviced and a
host of other variables will impact what your watch requires to stay wound.
And a watch winder won't wind a watch that is fully stopped. So, you need to
manually wind the timepiece to get it running first. You will have to make this
determination by trying the various settings.
8
Run & Stop
Bi-directional
Watch Selection
(Right)
TPD selection
Watch Selection
(Left)
5Remote Control
6Fingerprint Lock
A. Admin Key
B. Fingerprint panel: Put your finger in here to identify.
C. LED Status: There are 3 LED status, blue light, red light and pink light.
1950
TPD
650
850
1000 750
LED Light Control
Power Switch
New Watch
Mode Key
A
A
B
C
B
C
Note:
Only 650,750,850,1000 and 1950 TPD can be adjusted by remote control.
Other TPD modes need to be adjusted manually by touchscreen.
9
Note:
· Factory Mode: Any fingerprint can be unlocked
· Status of successful fingerprint enter: The blue light will be on for 2 seconds.
· Status of unsuccessful fingerprint enter: The red light will flash for 3 times.
· The fingerprint sensor can set up to 20 fingerprint users(2 administrator
and 18 user accounts)
· The first two fingerprints entered are administrators by default.
· Please do not set duplicate fingerprints account.
6.1 Fingerprint Accounts Setting
6.1.1 Fingerprint Verification Setting Mode
1. First administrator fingerprint account setting:
Press and hold the fingerprint sensor panel for 7 seconds, do not release
your finger, after the blue indicator flashes 3 times, you can release your
finger, and then the pink indicator flashes once, indicating that it will enter
the fingerprint registration state: Using the fingerprint you defined as an
administrator, input 6 valid presses continuously on the panel, the blue light
will flash once every time you press it, until the system collects your finger-
prints 6 times, the blue light will be on for 2 seconds, indicating that the first
fingerprint entry is successful, and exit the fingerprint entry mode.
Note:
During fingerprint entry, if the red light flashes, it is invalid entry, and it is
necessary to continuously enter valid fingerprints for 6 times with the blue
light flashing 6 times.
2. Second administrator fingerprint account setting:
Press and hold the fingerprint sensor panel for 7 seconds, do not release
your finger, after the blue indicator flashes 3 times, you can release your
finger, and then the pink indicator flashes once, indicating that you should
enter once your first administrator fingerprint to confirm, then put your
second administrator finger on the panel input 6 valid presses continuously.
The blue light will flash once every time you press it, until the system collects
your fingerprints 6 times, the blue light will be on for 2 seconds, indicating
that the second administrator fingerprint entry is successful.
There are two fingerprint setting modes: Using Fingerprint Verification OR
Using Admin Key.
Inhaltsverzeichnis
Andere DUKWIN Zubehör Handbücher
