Duratuf Sentry Shed SL1507 Bedienungsanleitung

ASSEMBLY INSTRUCTIONS

SL1507

BASE SIZE: 1.520m x 0.685m

CONGRATULATIONS ON PURCHASING A DURATUF SENTRY SHED.

BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE SOME IMPORTANT POINTS:

BEFORE YOU START:

• Read all instructions carefully

• Identify all parts and check quantities against parts list

• Select a level site

• Do not mark cladding with pencil as lead can cause corrosion to cladding

SAFETY:

• Do not attempt to build your shed in high winds

• Beware of sharp edges, recommend use of gloves

• Protect your eyes and ears

• For ease of assembly, use a friend to help

TOOLS REQUIRED:

WARRANTY REQUIREMENTS:

Following are the minimum requirements for cladding used in Sentry Sheds.

• Wash all surfaces annually using a hose and soft nylon brush.

• Within 2 km of coast – wash every 3 months as above. After a storm, wash the cladding and the gutters as soon

as possible to remove any highly corrosive salt deposits.

• Volcanic Ash Fallout – wash as soon as possible, removing fall out from roof and gutters.

• Do not allow manures, chemicals or other corrosive materials to have direct contact with cladding.

DRILL RIVETER 3.5mm DRILL BIT

HAMMER

LADDER

TAPE MEASURE 8mm HEX DRIVENAIL PUNCH

SQUARE DRILL BIT

SKILL SAW

(timber floor only)

SL1507 PARTS LIST

Back Wall - 1.810m 5

Side Wall 1 Pan Sheets- 1.810m 2

Front Wall Narrow Sheets—1.850 2

Roof - 0.885m 3

Door Sheet (Full Width) - 1.810m 1

Door Sides - 1.810m 2

Door Jamb - 1.850m 2

Door Brace - 0.915m 2

Barge - 0.885m 2

Spouting - 1.555m 1

Door Top/Bottom - 0.545m 2

Hardware Pack 1

Touchup Paint & Brush 1

Checked: Date:

CLADDING + FLASHING + HARDWARE

DESCRIPTION QTY DIAGRAM CHECKED

PACK 1

SL1507 PARTS LIST

PACK 2

TIMBER PACK

DESCRIPTION QTY DIAGRAM

Front/Back Bottom Plates - H4 (Green)

1.520 m 2

Back Top Plate - H1 (Red)

1.520 m 1

Front Top Plate - H1 (Red)

1.520 m 1

Side Wall Bottom Plates - H4 (Green)

0.685 m 2

Side Wall Top Plates - H1 (Red)

0.687m 2

SECURE SHED

ASSEMBLE BACK

PANEL

ASSEMBLE SIDE

PANELS

LAY FOUNDATION

ASSEMBLE DOOR

QUICK OVERVIEW

PARTS LOCATION

ASSEMBLE FRONT

PANEL

ASSEMBLE WALLS

ASSEMBLE ROOF

QUICK OVERVIEW

Top Plate Back

Side Wall Sheets

Roof Sheets

Top Plate Front

Bottom Plate Front

Bottom Plate Side

Back Wall Sheets

Front Wall Sheet

Door Jambs

Front Wall Narrow Sheet

Door Sheet

Door Side Flashing

Padbolt Support

Hinge

Door Top/Bottom

Barge Flashing

Spouting

Top Plate Side

Door Brace

FOUNDATION

SENTRY WOODEN FLOOR

• The optional Sentry kitset wooden floor is precut and designed to

be fitted into the shed after the shed is assembled.

• Assemble shed as per instructions and fit floor last.

(see page 13 for details).

CONCRETE SLAB FOR RAISED BASE PLATE SHED

To build a raised concrete slab for your shed to sit on, we recom-

mend the following:

• The raised slab size should be 15mm smaller than the base

size of the shed and at least 30mm above ground line.

• The slab should be 80mm thick in the middle and 100mm

thick around the edges.

• The slab should be laid on a solid or compacted base.

• Plastic sheeting under slab will prevent moisture coming

through from underneath.

• During construction, you may raise the bottom timber

plate to allow the wall cladding to protrude 20mm below

the bottom plate. This will stop water flowing between

the bottom plate and the concrete floor.

See note on page 7.

80mm

100mm

7.5mm

20mm

Concrete Floor

Base Plate

Wall Cladding

RAISED BASE PLATE OPTION

(For sheds placed on a raised concrete floor)

No doubt by now you will have decided what sort of base you are putting down.

Please read the section that applies to your situation.

If you choose to pour a concrete base you will need to decide whether you wish to raise the base plate of your shed.

This allows the cladding to protrude below the surface of the concrete and ensures a water tight pad.

See concrete pad specifications below

By choosing this option you will need to make the pad to the specification below.

SELECT:

1 x 1.810 m Door Sheet

2 x 0.545 m Door Top/Bottom Flashings

2 x 1.810 m Door Side Flashings

2 x 0.915 m Door Braces

1 x Padbolt Support Flashing

2 x Hinges

45 x Rivets

fig.3

ASSEMBLE DOOR

STEP 1:

• Lay out 1 x 1.810m Door Sheet on a flat

surface.

STEP 2:

• Position door side flashings and top

and bottom flashings and assemble

door as shown, ensuring narrow

face of flashing is on the front as

per fig. 1

STEP 4:

• On the back of the door, place door braces in posi-

tion as shown in fig.4.

• Ensure that the top and bottom ends of the braces

are under the door flashings as shown in fig.5 and

opposite ends of the braces overlap in the middle.

• Rivet door brace flashings onto back of door as

shown. Where possible, rivet from front of door.

STEP 3:

• Attach hinges to door side flashing using

rivets provided. Ensure hinge is flush

with back of door, and 60mm in from

each end as per fig.2.

• Using six rivets, attach padbolt support

as shown in fig. 3.

fig.4

fig.5

fig.2

Hinges

fig.1

ASSEMBLE SIDE PANELS

TOP PLATE

BOTTOM PLATE

1775mm 1798mm

TOP PLATE

15mm 15mm

TOP PLATE

BOTTOM PLATE

1775mm

1798mm

Second Side

Panel

BOTTOM PLATE

TOP PLATE

SELECT:

2 x 1.810 Wall Sheets

2 x 1.810 1 Pan Wall Sheets

2 x 0.685 Top Plates (Red)

2 x 0.685 Bottom Plates (Green)

32 x 30mm Galv Clouts

4 x Rivets

STEP 2:

• Place 1 x 1.810 wall sheet and 1 x Pan wall sheet on top of timber

plates, with sheets flush with each other.

STEP 3:

• Nail wall sheets to the Top Plate at each end making

sure that the top of the sheets are flush with the top of

the Top Plate and the sides of the wall sheet overhang

the Top Plate by approx 15mm as shown.

• Check that the Top Plate is straight then nail along the

wall sheet to the Top Plate, two clouts per pan (see

fig. 1).

STEP 4:

• Nail the wall sheets to the Bottom Plate at each end ensuring each

side of wall sheets overhangs the end of Bottom Plate by 15mm.

Check that the distance between the Top and Bottom Plates is

correct. (As per diagram in step 1)

• Check that the Bottom Plate is straight then nail the wall sheets to

the Bottom Plate, two clouts per pan (see fig. 1).

Repeat with second side panel ensuring Top Plate is positioned in

the OPPOSITE direction to the first side panel, as shown.

fig.1

RIB

PAN

CLOUT

TIMBER PLATE

Std Shed — Bottom Plate will protrude below wall

sheet by approximately 10mm.

Raised base plate shed — Wall sheet will protrude

below the Bottom Plate by 20mm.

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER

BASE PLATE –READ THE FOLLOWING;

For sheds with Raised Base Plate option only (see page 6), deduct

30mm from measurement shown between Top and Bottom Plates on

all wall panels, so cladding protrudes 20mm below bottom plate.

TOP PLATE

BOTTOM PLATE

15mm 15mm

1775mm 1798mm

15mm

RIVET

STEP 1:

• Lay out 1 x Top plate and 1 x Bottom plate on a flat surface as shown

(corner cut-outs to face outwards). Measurements between Top and

Bottom plates are critical to ensure wall panels fit together.

ASSEMBLE BACK PANEL

SELECT:

3 x 1.810m Wall Sheets

1 x 1.520 m Top Plate (Red)

1 x 1.520 m Bottom Plate (Green)

36 x 30mm Galv Clouts

4 x Rivets

STEP 1:

• Lay out 1 x Top Plate and 1 x Bottom Plate on a

flat surface as shown (corner cut outs to face in-

wards).

STEP 2:

• Place 3 x 1.810 m wall sheets on top of timber

Plates with bottom of sheets flush with each oth-

er.

• Rivet the sheets together on overlaps as shown.

STEP 3:

• Nail the wall sheets to the Top Plate at each end making sure

that the top of the sheets are flush with the top of the Top

Plate and that the sides of the wall sheets overhang the Top

Plate by 15mm as shown.

• Check that the Top Plate is straight then nail wall sheets to

the Top Plate, using two clouts per pan.

STEP 4:

• Nail the wall sheets to the Bottom Plate at each end,

ensuring that each side of the wall sheets overhangs the

Bottom Plate by 15mm and that the distance between

the Top and Bottom Plates is correct. (As shown)

• Check that the Bottom Plate is straight then nail

wall sheets to the Bottom Plate, using two clouts per pan.

Std Shed — Bottom Plate will protrude below wall sheet by

approximately 10mm.

Raised base plate shed — Wall sheet will protrude below

the Bottom Plate by 20mm.

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER

BASE PLATE –READ THE FOLLOWING;

For sheds with Raised Base Plate option only (see page 6), deduct

30mm from measurement shown between Top and Bottom Plates on

all wall panels, so cladding protrudes 20mm below bottom plate.

BOTTOM PLATE

1776mm 1776mm

TOP PLATE

15mm 15mm

TOP PLATE

BOTTOM PLATE

TOP PLATE

BOTTOM PLATE

15mm 15mm

1776mm 1776mm

TOP PLATE

ASSEMBLE FRONT PANEL

SELECT:

2 x 1.850 Narrow Wall Sheets

1 x 1.520 Top Plate (Red)

1 x 1.520 Bottom Plate (Green)

2 x 1.850 Door Jamb Flashings

28 x 30mm Galv Clouts

17 x Rivets

STEP 1:

• Lay out 1 x Top Plate and 1 x Bottom Plate on a flat

surface as shown

STEP 2:

• Using 2 x 30mm clouts, nail the Door Jamb Flashing flush with

the top of the Top Plate at the correct measurement as shown

in plan view. Pre drill holes using a 3.5mm drill bit

• Check the distance between the top and bottom plates then use

a further 2 x 30mm clouts to nail the Door Jamb Flashings to

the bottom Plate. Pre drill holes.

STEP 4:

• Place the door on the panel (In open position, approx

20mm below top of top plate). Using two rivets, rivet the top

and bottom hinges to the Door Jamb Flashing, ensuring

door closes properly.

• Fit remaining rivets.

STEP 3:

• Place 2 x Narrow Wall Sheets on timber. Make sure the nar-

row pans are next to the door. Ensure wall sheets fit under-

neath door jamb flashings.

• Ensure that the top of the sheets are flush with the top of the

Top Plate and that the sides of the wall sheets overhang the

Top Plate by 15mm as shown. Nail wall sheets to Top Plate

(two clouts per pan)

• Nail the wall sheets to the Bottom Plate making sure that the

Plates are the correct distance apart and that the sides of the

wall sheets overhang the Bottom Plate by 15mm.

• Drill & rivet Door Jamb Flashings to wall sheets using four

rivets equally spaced on each side.

NOTE: Door can be hinged on either side.

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER

BASE PLATE –READ THE FOLLOWING;

For sheds with Raised Base Plate option only (see page 6), deduct

30mm from measurement shown between Top and Bottom Plates on

all wall panels, so cladding protrudes 20mm below bottom plate.

BOTTOM PLATE

1799mm 1799mm

TOP PLATE

15mm 15mm

480mm 560mm

TOP PLATE

DOOR OPENING

TOP

PLATE

DOOR

JAMB

NAIL

Plan View

Inhaltsverzeichnis

Andere Duratuf Außenlagerung Handbücher

Duratuf

Duratuf Wairarapa Bedienungsanleitung

Duratuf

Duratuf GL57 Bedienungsanleitung

Duratuf

Duratuf GL75 Bedienungsanleitung

Duratuf

Duratuf PL46 Bedienungsanleitung

Duratuf

Duratuf SENTRY SS2007 Bedienungsanleitung

Duratuf

Duratuf GL95D Bedienungsanleitung

Duratuf

Duratuf GG109 Bedienungsanleitung

Duratuf

Duratuf GUARDIAN SHED GL37 Bedienungsanleitung

Duratuf

Duratuf SL1520 Bedienungsanleitung

Duratuf

Duratuf TUF 800 Bedienungsanleitung

Duratuf

Duratuf Guardian Sheds GS73 Bedienungsanleitung

Duratuf

Duratuf GL65 Bedienungsanleitung

Duratuf

Duratuf Gurdian Sheds GG101 Bedienungsanleitung

Duratuf

Duratuf SENTRY SHEDS SS1515 Bedienungsanleitung

Duratuf

Duratuf SG2020 Bedienungsanleitung

Duratuf

Duratuf PG99 Bedienungsanleitung

Duratuf

Duratuf TUF 100 Bedienungsanleitung

Duratuf

Duratuf SL1020 Bedienungsanleitung

Duratuf

Duratuf KAIPARA Bedienungsanleitung

Duratuf

Duratuf GG99 Bedienungsanleitung

Duratuf

Duratuf Garrison PL84 Bedienungsanleitung

Duratuf

Duratuf SG3020 Bedienungsanleitung

Duratuf

Duratuf SL2515 Bedienungsanleitung

Duratuf

Duratuf PG98 Bedienungsanleitung

Beliebte Außenlagerung Handbücher anderer Marken

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Bedienungsanleitung

TYGO

TYGO Nyland Bedienungsanleitung

Viking

Viking SD5300SS Technisches Handbuch

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Bedienungsanleitung

ModuLaro

ModuLaro Lojo WC202200 Bedienungsanleitung

Lifetime

Lifetime 6418 Bedienungsanleitung

rollaway container

rollaway container ARPCA24 Bedienungsanleitung

X-METAL

X-METAL 4065 Bedienungsanleitung

Outdoor Life Products

Outdoor Life Products FP2030 F Bedienungsanleitung

Royalcraft

Royalcraft Faro 295L Storage Box Bedienungsanleitung

Riverlea

Riverlea Duratuf KIWI KS3 Bedienungsanleitung

Rubbermaid

Rubbermaid 5L45 Bedienungsanleitung

garofalo

garofalo TUSCANY EVO Bedienungsanleitung

OLT

OLT GS84D-FJ-Plywood Bedienungsanleitung

Eden

Eden CA2988 Bedienungsanleitung

Palram

Palram CANOPIA RUBICON 6x10 Administratorhandbuch

Suncast

Suncast 774098 Bedienungsanleitung

Lifetime

Lifetime 60186 Bedienungsanleitung