Duratuf KAIPARA Bedienungsanleitung

ASSEMBLY INSTRUCTIONS

BASE SIZE: 3.900m x 2.550m

KAIPARA

BEFORE YOU BEGIN THE ASSEMBLY PLEASE NOTE

SOME IMPORTANT POINTS

TOOLS REQUIRED

• Drill

• Hex Drive (5/16)

• Hex Drive (3/8)

• Drill Bit 3.5mm

• Drill Bit 10mm

• Square Drive Drill Bit

• Phillips Drill Bit

• Slotted Drill Bit

• Riveter

• Hammer

• Tape Measure

• Ladder

• String Line

• Adjustable Spanner

• Level

• Hand Saw

• Caulking Gun

• Tin Snips (Left & Right Hand)

• Flatle(ForRollerDoor)

• Pipe Wrench (For Roller Door)

• SkillsawandJigsaw(Foroptionaltimberoor)

• MasonryDrilland12mmMasonryBit(forconcreteoor)

BEFORE YOU START

• Read all instructions carefully.

• Identify all parts and check quantities against checklist, before starting.

SAFETY

• Do not attempt to build your shed in high winds.

• Beware of sharp edges.

• Protect your eyes and ears.

• Use electronic tools with care. Use a Safety Trip Switch.

• It is easier and quicker if this shed is erected by two people.

SELECT YOUR SITE

• Your shed must be level. Achieve this by either levelling the ground or by using blocks.

• Ifyourshedistobepositionedonwetordampground,werecommendthatyourshedisraisedupo󰀨the

ground slightly.

WARRANTY REQUIREMENTS

The following maintenance process needs to be adhered to, to qualify for the steel warranty of your Duratuf

Guardian shed.

• Wash all surfaces annually using a hose and soft nylon brush.

• Within 2 km of coast – wash every 3 months as above. After a storm, wash the cladding and the gutters as

soon as possible to remove any highly corrosive salt deposits.

• Volcanic Ash Fallout – wash as soon as possible, removing fall out from roof and gutters.

• Do not allow manures, chemicals or other corrosive materials to have direct contact with cladding.

PARTS LIST

TIMBER

DESCRIPTION LENGTH QTY DIAGRAM CHECKED

Front/Back Base Plate 70 x 45 H4 (Green) 3.900m 2

End Base Plate 70 x45 H4 (Green) 2.410m 2

Front/Back Top Plate 70 x 45 H1 (Red) 3.900m 2

EndTop Plate 70 x 45 H1 (Red) 2.410m 2

Lintel 70 x 45 2.400m 1

Stud 70 x 45 (Yellow) 2.295m 10

Stud 70 x 45 (Yellow) 2.440m 6

Stud 70 x 45 (Yellow) 0.320m 3

Nog 70 x 45 1.240m 3

Nog 70 x 45 1.137 4

Nog 70 x 45 0.615m 2

Ridge Beam 140 x 45 H1 with 67mm notch 3.900m 1

DESCRIPTION LENGTH QTY DIAGRAM CHECKED

Back Wall Sheet 3.900m 3

End Wall Sheet 2.550m 6

Roof Sheet 3.150m 5

Front Wall Sheet 0.750m 6

Half Front Wall Sheet (390mm wide) 3.900m 1

Roller Door 2.400m 1

CLADDING/FLASHING

DESCRIPTION LENGTH QTY PART# DIAGRAM CHECKED

Front Top Plate Flashing 3.900m 1 1001

Front Corner Flashing 2.540m 2 1002

Rear Corner Flashing 2.400m 2 1003

Door Top Flashing 2.590m 1 1004

Door Head Flashing 2.400m 1 1005

Door Jamb Flashing 2.105m 2 1006

Downpipe Cover Flashing 2.200m 1 1007

Barge Flashing 3.225m 2 1008

Front Spouting 4.005m 1 1009

Back Spouting 4.005m 1 1010

Spouting End Cap 0.120m 2 1011

HARDWARE/ACCESSORIES

DESCRIPTION LENGTH QTY DIAGRAM CHECKED

L-Brackets 40mm 2

Flathead Nails 90mm 160

Tek Screws 55mm 110

Tek Screws 25mm 220

Clouts 30mm 130

Tek Screws 100mm 16

Rivets 3.2mm 80

Dropper 80mm 1

Downpipe 80mm 3.000m 1

Downpipe Brackets 2

Silicone 1

Roll of DPC 30m 1

Touch up paint and brush 1

DATE: / / PACKED BY:

TIMBER FLOOR

DESCRIPTION LENGTH QTY DIAGRAM CHECKED

Floor Joists 100 x 50 H4 3.880m 6

Floor Boards 150 x 25 H3 2.530m 26

Door Step Flashing 2.400m 1

Floor Nails 50mm 330

OPTIONAL EXTRAS

CLEAR ROOF

DESCRIPTION LENGTH QTY DIAGRAM CHECKED

Clear Roof Panel 3.150m 1

PLY FLOOR

DESCRIPTION LENGTH QTY DIAGRAM CHECKED

Plywood 17mm treated 1.940m x 1.200m 4

Plywood 17mm treated 1.940m x 0.130m 2

Joists 70 x 45 H4 3.790m 6

Joists 70 x 45 H4 2.530m 2

Joists 70 x 45 H4 0.532m 1

Joists 70 x 45 H4 0.555m 3

Joists 70 x 45 H4 0.063m 1

Door Step Flashing 2.400m 1

Floor Screws 40mm 120

Floor Screws 75mm 100

FOUNDATIONS

• No doubt by now you will have decided what sort of base you are

putting down.

• If you choose a raised foundation, either a concrete base, plywood

oor,ortimberoor,thesheddesignpreventsthewaterfrom

owinginsidetheshed.

• If you chose to position the shed directly onto the ground, the

watercanowdownthewallsandunderthebottomplateandinto

the shed.

CONCRETE BASE

• To build a concrete base we recommend the following.

• Concrete base should be 3880mm x 2530mm (this is

20mm smaller than the shed frame size, which allows

for a 10mm gap around the perimeter of the shed).

• Concrete base to be a minimum of 80mm thick and at least 100mm thick around the perimeter. Base should

be at least 50mm above ground line.

• Concrete base should be laid on a solid or compacted base.

• Plastic sheeting underneath concrete will prevent moisture coming through underneath.

• Ideallytheareaaroundthedoorwayshouldhaveaslightslopetoallowwatertoruno󰀨.Refertoplansfor

doorway position.

10mm

100mm

80mm

PLYWOOD FLOOR

Select

6 x 3790mm Joists

2 x 2530mm Joists

1 x 532mm Joists

1 x 63mm Joists

3 x 555mm Joists

4 x Ply 1945mm x 1200mm

2 x Ply 1945mm x 130mm

• Layoutoorjoistsandassemblesuboor

frame as shown, nailing joists together

with two 90mm nails per join.

SUB FLOOR FRAME

• Positionsuboorframeensuring

frame is well supported, level and

diagonals are correct.

• Using 40mm screws, screw plywood

tosuboorframeasshown.

• Ensuretimberoorissu󰀩ciently

secured down to foundation.

PLYWOOD SHOWING SCREWS Screws

1200mm1200mm

Screws

1945mm

130mm

3790mm

532mm

555mm

2530mm

63mm

1895mm 1895mm

TIMBER FLOOR

Select

6 x 3880mm Joists

26 x 2530mm Floor boards

• Layoutoorjoistsasshown,ensuring

joists are spaced evenly apart.

• Using50mmooringnails,nailaoor

board on each end, ensuring ends are

ushwithjoists.Makesureoorislevel

and joists are well supported.

SUB FLOOR FRAME

• Layoutremainingoorboards.

• Measure diagonals to ensure

measurementsareequalandooris

sqare.

• Ripdownlastoorboardtosuitgap

andnailo󰀨oorwith50mmooring

nails (12 nails per board).

• Ensuretimberoorissu󰀩ciently

secured down to foundation.

3880mm

2530mm

TIMBER SHOWING NAILS

2530mm

Nails

..........................................

3880mm

..........................................

TIMBER FRAME

2385

End Base Plates - 2

BFront/Back Base Plates - 2

CEnd Top plates - 2

DFront/Back Top Plates - 2

EStuds - 19

FRidge beam - 1

GNogs - 9

HLintel - 1

3900

2550

TIMBER FRAME - END WALLS

Select

2 x 2410mm Base Plates

2 x 2410mm Top Plates

6 x 2295mm Studs

4 x 1137mm Nogs

• Select one 2410mm base plate

(Green), one 2410mm top plate

(Red) and three studs (Yellow).

• Lay out plates and three studs

onaatsurfaceandnail

together using two 90mm nails

per join. Studs are positioned

1137mm apart.

• Position nogs 1200mm up from

underside of bottom plate to

centre of nog and nail in place.

• Repeat with second end wall

frame.

45 45 45

11081132

2375

1137

2410

1137

TIMBER SHOWING NAILS

1010

TIMBER FRAME - BACK WALL

TIMBER FRAME - FRONT WALL

• Nail lintel to studs using the 320mm studs to establish correct height.

• Nail 320mm studs to top plate and lintel, spacing these evenly apart.

Select

1 x 3900mm Base Plate

1 x 3900mm Top Plate

1 x 2400mm Lintel

6 x 2440mm Studs

3 x 320mm Studs

2 x 615mm Nogs

• Select one 3900mm base plate

(Green), one 3900mm top plate

(Red) and four studs (Yellow). Lay

outplatesandtwostudsonaat

surface and nail together using two

90mm nails per join.

• Nail one stud each side of doorway

to top and bottom using the 615mm

nogs to establish correct position.

• Nail remaining two studs to inside

of studs and top and bottom plates

to make a double stud each side of

doorway opening.

320

2110

615

3900

2530

2400

615 90

45 90

45 45

1132 1263

Select

1 x 3900mm Base Plate

1 x 3900mm Top Plate

4 x 2295mm Studs

3 x 1240mm Nogs

• Select one 3900mm base plate

(Green), one 3900mm top plate

(Red) and four studs (Yellow).

• Lay out plates and four studs on a

atsurfaceandnailtogetherusing

two 90mm nails per join. Studs are

positioned 1240mm apart.

• Position nogs 1200mm up from

underside of bottom plate to centre

of nog and nail in place. 45 45 45

45 45 45

1118

1132 2385

1240

3900

1240

Andere Handbücher für KAIPARA

Inhaltsverzeichnis

Andere Duratuf Außenlagerung Handbücher

Duratuf

Duratuf SG2020 Bedienungsanleitung

Duratuf

Duratuf Guardian Sheds GS73 Bedienungsanleitung

Duratuf

Duratuf PL46 Bedienungsanleitung

Duratuf

Duratuf GL75D Bedienungsanleitung

Duratuf

Duratuf PG98 Bedienungsanleitung

Duratuf

Duratuf MATAKANA Bedienungsanleitung

Duratuf

Duratuf MK4A Bedienungsanleitung

Duratuf

Duratuf Garrison PL36 Bedienungsanleitung

Duratuf

Duratuf TUF 100 Bedienungsanleitung

Duratuf

Duratuf MARLBOROUGH Bedienungsanleitung

Duratuf

Duratuf GS63 Bedienungsanleitung

Duratuf

Duratuf TUF 200 Bedienungsanleitung

Duratuf

Duratuf SL3015 Bedienungsanleitung

Duratuf

Duratuf Glenburn Bedienungsanleitung

Duratuf

Duratuf Garrison PL84 Bedienungsanleitung

Duratuf

Duratuf MK3B Bedienungsanleitung

Duratuf

Duratuf GL65 Bedienungsanleitung

Duratuf

Duratuf Garrison PL63 Bedienungsanleitung

Duratuf

Duratuf GG109 Bedienungsanleitung

Duratuf

Duratuf Smart store SS1507 Bedienungsanleitung

Duratuf

Duratuf GS62 Bedienungsanleitung

Duratuf

Duratuf SL1520 Bedienungsanleitung

Duratuf

Duratuf TUF 800 Bedienungsanleitung

Duratuf

Duratuf TUF LOCKER Bedienungsanleitung

Beliebte Außenlagerung Handbücher anderer Marken

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Bedienungsanleitung

TYGO

TYGO Nyland Bedienungsanleitung

Viking

Viking SD5300SS Technisches Handbuch

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Bedienungsanleitung

ModuLaro

ModuLaro Lojo WC202200 Bedienungsanleitung

Lifetime

Lifetime 6418 Bedienungsanleitung

rollaway container

rollaway container ARPCA24 Bedienungsanleitung

X-METAL

X-METAL 4065 Bedienungsanleitung

Outdoor Life Products

Outdoor Life Products FP2030 F Bedienungsanleitung

Royalcraft

Royalcraft Faro 295L Storage Box Bedienungsanleitung

Riverlea

Riverlea Duratuf KIWI KS3 Bedienungsanleitung

Rubbermaid

Rubbermaid 5L45 Bedienungsanleitung

garofalo

garofalo TUSCANY EVO Bedienungsanleitung

OLT

OLT GS84D-FJ-Plywood Bedienungsanleitung

Eden

Eden CA2988 Bedienungsanleitung

Palram

Palram CANOPIA RUBICON 6x10 Administratorhandbuch

Suncast

Suncast 774098 Bedienungsanleitung

Lifetime

Lifetime 60186 Bedienungsanleitung