Dynabrade 51520 Kurzanleitung

Disassembly Instructions - Wet, Stone Polisher

Model: 51520

Important: Use these instructions along with tool parts page or manual.

Notice:

Shut off air supply and depress throttle lever to deplete air.

Disconnect tool from air supply hose.

Shut off water supply faucet and disconnect.

Remove all accessories (abrasive product, backup disc, and flanges) from tool.

Motor Disassembly:

1. Push against collar of 96227 Fitting and pull 95579 Water Line tubing from fitting.

2. Install 95492 Screws (5/16"-18 SHC) in two handle bosses on housing.

Fasten 95492 Screws in vise to hold tool with 51546 Valve Body pointing up.

Use a 3 mm hex key to remove 96296, 95916 Screws along with 01211 Lock

Washers. Turn counterclockwise.

Carefully remove valve body assembly, spacers, gaskets and o-rings.

Set aside and save parts.

3 mm hex key

3. Remove motor form housing.

4. Fasten 96346 Bearing Separator (2") around 01028 Cylinder.

Place assembly in 96232 Arbor Press (#2) with pinion pointing down.

Use a Ø 1/4" drive punch to push 02373 Rotor out of 02649 Bearing.

96346 Bearing Separator

5. NOTICE: In the same way, use bearing separator, arbor press and 96213 Bearing

Removal Tool, to remove 02649 Bearing from 01732 Rear Bearing Plate.

Save parts.

96213 Bearing Removal Tool

6. Fasten 02373 Rotor in vise with aluminum or bronze jaws, with pinion pointing up.

Use an adjustable hook spanner wrench to remove 51513 Pinion Gear. Turn

counterclockwise.

Remove front bearing, plate, spacer and shims.

Motor disassembly completed.

Clean and inspect parts for wear or damage. Save and reuse good parts.

Right Angle Gear Disassembly:

1. Install 95492 Screws (5/16"-18 SHC) in two handle bosses on housing.

Fasten 51545 Housing in vise with spindle pointing up.

Use a HEAT GUN to warm housing.

Use an adjustable pin spanner wrench to remove 51551 Spindle Retainer. Turn

clockwise. Left Hand Thread.

HEAT

GUN

2. Loosen vise and remove housing.

Remove 96584 O-Ring.

Remove spindle and bevel gear assembly.

Remove 98243 Wave Spring.

3. Fasten 96346 Bearing Separator (2") under 02057 Bearing.

Place assembly in 96232 Arbor Press (#2) with threaded end of spindle pointing

down.

Use a Ø 3/16" drive punch to push spindle out of 02057 Bearing.

NOTICE: In the same way, use bearing separator and arbor press to remove

51514 Gear and 02685 Bearing.

IMPORTANT: Inspect 95913 Seals and 51550 Spindle. Replace worn parts!

NOTICE: Loctite #380 is used to retain 95913 Seals in 51551 Spindle Retainer.

Acetone can be used to soften adhesive and remove seals. SEE: Right Angle

Gear Assembly.

Right angle gear disassembly completed.

Clean and inspect all parts for wear or damage. Only reuse good parts.

Notice: To disassemble and assemble muffler and valve components, refer to

parts page or tool manual and follow exploded view instructions.

96346 Bearing Separator

Assembly Instructions - Wet, Stone Polisher

Motor Assembly:

1. Install 01010 Spacer onto rotor.

Install .003" (~0.08 mm) shim thickness into 02375 Front Bearing Plate.

Install 01007 Bearing into front bearing plate.

Install bearing and plate onto rotor.

Andere Dynabrade Sander Handbücher

Dynabrade

Dynabrade Dynorbital-Spirit 21000 Handbuch

Dynabrade

Dynabrade Dynabug 10278 Leitfaden

Dynabrade

Dynabrade 52560 Leitfaden

Dynabrade

Dynabrade Dynorbital 57130 Bedienungsanleitung

Dynabrade

Dynabrade 56801 Bedienungsanleitung

Dynabrade

Dynabrade 57240 Bedienungsanleitung

Dynabrade

Dynabrade Dynabug 57920 Benutzerhandbuch

Dynabrade

Dynabrade Dynorbital 57610 Bedienungsanleitung

Dynabrade

Dynabrade 300CE Leitfaden

Dynabrade

Dynabrade 10725 Bedienungsanleitung

Dynabrade

Dynabrade Dynorbital-Spirit 21000 Bedienungsanleitung

Dynabrade

Dynabrade Dynorbital-Spirit 21000 Bedienungsanleitung

Dynabrade

Dynabrade 53270 Leitfaden

Dynabrade

Dynabrade 10600 Montageanleitung

Dynabrade

Dynabrade 50348 Bedienungsanleitung

Dynabrade

Dynabrade 4657971919 Bedienungsanleitung

Dynabrade

Dynabrade Mini-Dynafile II 15003 Leitfaden

Dynabrade

Dynabrade 51479 Bedienungsanleitung

Dynabrade

Dynabrade 50347 Benutzerhandbuch

Dynabrade

Dynabrade Dynabug 57860 Bedienungsanleitung

Dynabrade

Dynabrade Dynalocke 10770 Bedienungsanleitung

Dynabrade

Dynabrade 51830 Bedienungsanleitung

Dynabrade

Dynabrade Mini-Dynorbital Silver Supreme 69500 Leitfaden

Dynabrade

Dynabrade Dynabug II 58500 Leitfaden

Beliebte Sander Handbücher anderer Marken

Oliver

Oliver 6305 Bedienungsanleitung

Jet

Jet 22-44 Pro-3 Service-Handbuch

Makita

Makita M9204 Handbuch

Makita

Makita M9204 Bedienungsanleitung

Craftsman

Craftsman 351.215131 Bedienungsanleitung

Clarke

Clarke Woodworker CBS1-5B Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP9778 Bedienungsanleitung

Nitto Kohki

Nitto Kohki BB-20 Bedienungsanleitung

Ferm

Ferm FEOS-135 Bedienungsanleitung

Unior

Unior 1510 Bedienungsanleitung

stayer

stayer ls1200 Bedienungsanleitung

Jet

Jet JSG-96 Service-Handbuch

Parkside

Parkside PDS 290 B2 Bedienungsanleitung

Status

Status XPA Series Bedienungsanleitung

Clarke

Clarke EZ Sand Bedienungsanleitung

Craftsman

Craftsman 113.22521 Bedienungsanleitung

Craftsman

Craftsman 113.225831 Bedienungsanleitung

CLAS

CLAS OP 1429 Bedienungsanleitung